Aortic valve papillary fibroelastoma. A diagnosis by transthoracic echocardiography

Cardiac papillary fibroelastomas are unusual, frond-like growths typically found on cardiac valves, diagnosed incidentally on autopsy or cardiac surgery, but rarely during life. We report a rare case of an aortic valve papillary fibroelastoma detected by transthoracic echocardiography and confirmed by histologic study.     

Room temperature synthesis of crystalline metal oxides

Crystalline titanium dioxide powders have been synthesized as either rutile or anatase from aqueous solutions at low temperatures (T≤100°C) and atmospheric pressure. First, a sol is prepared by the hydrolysis of a titanium alkoxide in an acidic solution. The sol is subsequently heated at different rates to produce the different crystalline phases of titanium dioxide. Powder characterization was carried out using X-ray diffraction, scanning electron microscopy and high resolution transmission electron microscopy. In general, the precipitate size was observed to be between 50 and 100 nm. Possible mechanisms involved in determining the crystal variants are discussed. This revised version was published online in November 2006 with corrections to the Cover Date.     

Structural Studies of TeO2–SeO2–Na2O Glass System

Glass Physics and Chemistry - The growth of nanocrystalization in TeO2–SeO2–Na2O glasses is achieved by the conventional heat treatment method. The influence of Na2O concentration on...     

Recovery and Recycling Silica Flux in Submerged Arc Welding – Acceptable Properties and Economical Correlation

Silicon - This research aims at optimum utilization of waste recycled submerged arc welding slag along with virgin flux in place of pure virgin flux without compromising the quality of welding and...     

2-DOF vibratory gyroscope fabricated by SU-8 based UV-LIGA process

This paper reports fabrication of 2-DOF vibratory gyroscope using SU-8 based UV-LIGA process. The device structure is designed to be symmetrical in order to match the resonance frequencies of drive and sense mode oscillators and also to minimize their relative temperature dependent drift. The overall arrangement is such that the two vibration modes do not affect each other and therefore, mechanical decoupling is achieved which helps in minimizing bias drift. The design is optimized to be compatible with the UV-LIGA process having 10 μm thick electroformed nickel as structural layer. Photolithography to create 11 μm thick SU-8 molds for electroforming sacrificial copper and structural nickel layer is optimized using multiple exposure technique that ensures near vertical side walls. Since the highly cross-linked SU-8 remaining after development is difficult to remove reliably from high aspect ratio structures without damage or alteration to the electroformed metals, a 2.45 GHz MW plasma etching process is developed with CF₄/O₂ mixes. The fabricated device is checked for off-plane misalignment between the stationary and movable comb fingers using white light interferometry and it is found to be almost negligible. Also, the prototype device is characterized for amplitude and phase spectral responses using Polytec MSA-500 Micro System Analyzer. The drive and sense mode resonance frequencies are observed at 7.3 and 7.1 kHz respectively against the mode matched designed frequency of 7.5 kHz.     

Vapor-Phase Alkylation of Toluene with Isopropanol over Mg/Al, Ni/Al and Cu/Al Hydrotalcites (Layered Double Hydroxide)

Vapor-phase isopropylation of toluene has been carried out over Mg/Al, Ni/Al and Cu/Al calcined hydrotalcites (CHTs). Reaction conditions were optimized for alkylation by varying temperature, weight hourly space velocity and reactant mole ratio. Side-chain alkylation is found to be more predominant than ring alkylation over Mg/Al CHT, while Ni/Al and Cu/Al CHTs favored ring alkylation. The main products were isobutylbenzene and cymene. The combined participation of acidic and basic sites of the materials is found to be crucial for both side-chain and ring alkylation of toluene with isopropanol. An X-ray diffraction pattern of the resulting oxide indicates a diffuse MgO structure. The incorporation of small amounts of Al³⁺ to MgO generates new surface Lewis acid--base pair sites.     

Vapour phase esterification of butyric acid with 1-pentanol over Al-MCM-41 mesoporous molecular sieves

Al-MCM-41 molecular sieves with Si/Al ratios 25, 50, 75 & 100 were synthesized hydrothermally and characterized systematically by various analytical and spectroscopy techniques. Their catalytic activity was evaluated for the vapour phase reaction of butyric acid with 1-pentanol. Pentyl butyrate was obtained as the only product. Reaction parameters such as temperature, molar ratio and feed rate were optimized for higher butyric acid conversion. The time-on-stream study was carried out at optimum conditions resulting in gradual decrease in the activity of the catalyst.     

Occurrence of wax esters and 1-O-alkyl-2,3-diacylglycerols in goat epididymal sperm plasma membrane

Two unusual lipid classes were detected by thin-layer chromatography in the neutral lipids derived from goat cauda-epididymal sperm plasma membrane. The lipids were identified as wax esters and 1-O-alkyl-2,3-diacylglycerols based on chromatographic properties, identity of their hydrolysis products, and infrared/¹H nuclear magnetic resonance spectral evidence. The membrane containedca. 3 and 5 μg/mg protein of wax esters and alkyldiacylglycerols, respectively. The relative proportions of wax esters and alkyldiacylglycerols in the total neutral lipids were 1.5% and 2.4%, respectively. The lipids contained fatty acids with chain lengths of C₁₄ to C₂₂. The major fatty acids of the wax esters were 14∶0, 16∶0, 16∶1ω7, 18∶0 and 18∶1ω9. The fatty acids in alkyldiacylglycerol were 16∶0, 18∶0, 22∶5ω3 and 22∶6ω3. Alkyldiacylglycerol was particularly rich in docosahexaenoic acid 22∶6ω3) representing 30% of the total fatty acids. The alcohols of wax ester were all saturated with C₂₀–C₂₉ carbon chains. The deacylated products derived from alkyldiacylglycerols were identified as hexadecyl, octadecyl and octadec-9′-enyl glycerol ethers.     

Phase evolution and <110>-orientation mechanism in RTGG-processed BaTiO3 ceramics with electrical properties

The <110>-oriented BaTiO₃ ceramics were fabricated using BaCO₃ matrix and H_1.08Ti_1.73O₄.nH₂O (HTO) template particles, and the mechanism of BaTiO₃ phase formation was investigated. The dielectric, ferroelectric, and piezoelectric properties were also investigated. The transformation of the HTO phase into the TiO₂ bronze or TiO₂ (B) phase was observed at 600°C, where the BaTiO₃ nucleation was accompanied by the formation of a Ba₂TiO₄ phase. The TiO₂ phase reacted with the Ba₂TiO₄ phase at 800°C to give a BaTiO₃ phase, whereas its reaction with the BaTiO₃ resulted in the formation of BaTi₂O₅ phase that got decomposed into BaTiO₃ and Ba₆Ti₁₇O₄₀ phase at sintering temperature ≥1300°C. Sintering with samples’ embedding in BaTiO₃ powders prevented the formation of the Ba₆Ti₁₇O₄₀ secondary phase. The crystallographic orientation along the <110> direction (F₁₁₀) was developed by the epitaxial grain growth mechanism. In addition to the contribution of the grain-size increment for enhancing the F₁₁₀, the preservation of the platelike structure was also found to have a significant impact. The ceramics prepared by the embedded sintering (grain size ≈12.4 µm and F₁₁₀ = 83%) exhibited the room-temperature dielectric constant of 1708 and piezoelectric strain constant of 445 pm/V, which are higher than those of the BaTiO₃ ceramics with randomly oriented grains.