Long-term sensor measurements of lung deposited surface area of particulate matter emitted from local vehicular and residential wood combustion sources

Abstract

Lung deposited surface area (LDSA) is a relatively new metric that has been argued to be more accurate at predicting health effects from aerosol exposure. For typical atmospheric aerosol, the LDSA concentration depends mainly on the concentration of ultrafine particles (e.g. vehicular exhaust emissions and residential wood combustion) and therefore optical methods cannot be used to measure and quantify it. The objective of this study was to investigate and describe typical characteristics of LDSA under different urban environments and evaluate how a diffusion charging-based Pegasor AQ Urban sensor (Pegasor Ltd., Finland) can be used as an alternative to optical sensors when assessing local combustion emissions and respective LDSA concentrations. Long-term (12?months) sensor measurements of LDSA were carried out at three distinctly different measurement sites (four sensor nodes) in the Helsinki metropolitan area, Finland. The sites were affected mainly by vehicular exhaust emission (street canyon and urban background stations) and by residential wood combustion (two detached housing area stations). The results showed that the accuracy of the AQ Urban was good (R² = 0.90) for the measurement of LDSA when compared to differential mobility particle sizer. The mean concentrations of LDSA were more than twice as high at the street canyon (mean 22 µm² cm^?3) site when compared to the urban background site (mean 9.4 µm² cm^?3). In the detached housing area, the mean concentrations were 12 µm² cm^?3, and wood combustion typically caused high LDSA peaks in the evenings. High correlations and similar diurnal cycles were observed for the LDSA and black carbon at street canyon and urban background stations. The utilization of a small-scale sensor network (four nodes) showed that the cross-station variability in hourly LDSA concentrations was significant in every site, even within the same detached housing area (distance between the two sites ～670?m).     

Heat and Mass Transfer Analogy Studies of Binary Liquid Mixture in Comparison with Eteanol-n-Heptane Evaporating to Air

An expenmental and theoretical study of heat and mass transfer analogy and a comparison of that to a binary liquid mixture evaporation is presented. Common organic solvents, ethanol and n-heptane, were used to form an alcohol - hydrocarbon mixture. Studies were carried out in a horizontal rectangular channel having air flow velocities of 0.2 - 0.9 m/s. Heat transfer coefficients were measured with a copper plate resistor and mass transfer coefficients with a square pool. The heat and mass transfer analogy is presented for a system having two evaporating compounds with a fixed value of air flow and verified by measuring and comparing mass transfer coefficients for distilled water with air flow velocities of 0.2 - 0.9 mls. An illustrative example of the use of the theory for industrial ventilation is presented.     

Deterministic Polymorphic Engineering of MoTe2 for Photonic and Optoelectronic Applications

Developing selective and coherent polymorphic crystals at the nanoscale offers a novel strategy for designing integrated architectures for photonic and optoelectronic applications such as metasurfaces, optical gratings, photodetectors, and image sensors. Here, a direct optical writing approach is demonstrated to deterministically create polymorphic 2D materials by locally inducing metallic 1T′-MoTe₂ on the semiconducting 2H-MoTe₂ host layer. In the polymorphic-engineered MoTe₂, 2H- and 1T′- crystalline phases exhibit strong optical contrast from near-infrared to telecom-band ranges (1–1.5 µm), due to the change in the band structure and increase in surface roughness. Sevenfold enhancement of third harmonic generation intensity is realized with conversion efficiency (susceptibility) of ≈1.7 × 10⁻⁷ (1.1 × 10⁻¹⁹ m² V⁻²) and ≈1.7 × 10⁻⁸ (0.3 × 10⁻¹⁹ m² V⁻²) for 1T′ and 2H-MoTe₂, respectively at telecom-band ultrafast pump laser. Lastly, based on polymorphic engineering on MoTe₂, a Schottky photodiode with a high photoresponsivity of 90 AW⁻¹ is demonstrated. This study proposes facile polymorphic engineered structures that will greatly benefit realizing integrated photonics and optoelectronic circuits.     

Nanowire encapsulation with polymer for electrical isolation and enhanced optical properties

Light management and electrical isolation are essential for the majority of optoelectronic nanowire (NW) devices.Here,we present a cost-effective technique,based on vapor-phase deposition of parylene-C and subsequent annealing,that provides conformal encapsulation,anti-reflective coating,improved optical properties,and electrical insulation for GaAs nanowires.The process presented allows facile encapsulation and insulation that is suitable for any nanowire structure.In particular,the parylene-C encapsulation functions as an efficient antireflection coating for the nanowires,with reflectivity down to ＜1％ in the visible spectrum.Furthermore,the parylene-C coating increases photoluminescence intensity,suggesting improved light guiding to the NWs.Finally,based on this process,a NW LED was fabricated,which showed good diode performance and a clear electroluminescence signal.We believe the process can expand the fabrication possibilities and improve the performance of optoelectronic nanowire devices.     

Flexible multibody approach in forward dynamic simulation of locomotive strains in human skeleton with flexible lower body bones

A method for bone strain estimation is examined in this article. The flexibility of a single bone in an otherwise rigid human skeleton model has been studied previously by various authors. However, in the previous studies, the effect of the flexibility of multiple bones on the musculoskeletal model behavior was ignored. This study describes a simulation method that can be used to estimate the bone strains at both tibias and femurs of a 65-year-old Caucasian male subject. The verification of the method is performed by the comparison of the results with other studies available in literature. The results of the study show good correlation with the results of previous empirical studies. A damping effect of the flexible bones on the model is also studied in this paper.     

Concerted utility review of VVER-440 safety research needs (VERSAFE)

There are twelve operating VVER-440/213 reactors in the Czech Republic, Hungary and Slovakia. The plant owners have carried out extensive safety enhancement programmes, which have included measures to improve prevention, mitigation and control of design basis accidents. Recently, there have been a number of projects to study the Severe Accident Management aspects of these plants. The plant owners have also initiated Plant Life Management programmes. The objective of the VERSAFE Concerted Action is to create a network of the VVER-440/213 plant owners and operators, which aims at definition of the further research needs of severe accidents and plant ageing from the utilities’ viewpoint. The starting point is to formulate a general approach to severe accident management and plant life management and then proceed to define the needs for the additional information expected from the safety research. The role of national research institutes and organisations of the partner countries is of crucial importance in performing such research and, thus, creating and maintaining the expertise on the national level. The successful completion of the project will assist in establishing well-defined research projects that are oriented to the needs of the end-users and provide information that can be used to facilitate and support the negotiations of the EU applicant countries operating VVER-440 reactors.     

Perceptions of the health and convenience characteristics of fresh and dried fruits

Dried fruits consumption has not received much research attention, although these foods are associated with potential health benefits. Therefore, the aim of this study was to compare fresh fruits and dried fruits on measures of health, convenience and consumer feelings.An on-line questionnaire that measured consumers' perceptions of the health benefits and convenience characteristics and their feelings about the consumption of both fresh fruits (apples and plums) and dried fruits (e.g., raisins, dates, and apricots) was completed by 693 respondents (Polish, French, and Dutch).Generally, fresh fruits were perceived to be healthier and less convenient than dried fruits. Consumers also reported more positive feelings about the consumption of fresh fruits compared to dried fruits. The more that the respondents were willing to sacrifice for their health, the more positively they rated the health aspects of both fresh and dried fruits, as well as several perceptions of convenience of both fresh and dried fruits. Health preoccupation was unrelated to most of the convenience perceptions and was associated with lower scores on several perceptions of healthiness. Recommendations for the consumer-oriented development of dried fruits are also provided.     

Challenges of manufacturability and product data management in bending

Effective production in a networking environment of sheet metal products needs accurate and relevant PDM (product data management) data, appropriate modeling of components supported by local and global network solutions, and utilization of advantages of feature-based modeling. To enable these aspects of effective production in sheet metal production, it is necessary to evaluate the integration of DFMA (design for manufacturing and assembly) and PDM. This paper aims at identifying the challenges of DFMA and PDM integration through recognizing possible malfunctioning parts of their integration. The observations are based on sheet metal specimens in which the DFMA and PDM aspects are visible in punching and bending. This study will focus on five issues that are included either in DFMA or PDM, or both: the effects of different calculation methods for the flattened length, utilization viewpoints of global or local manufacturability guidelines, assembly conditions, options to tune the manufacturing process instead of changing the product geometry, and possible additional requirements given by the customers. Based on practical design and manufacturing tests, it has become evident that one option to improve the quality of analyzed sheet metal parts is to further develop the integration of DFMA features with the workshop’s cutting and punching parameters. As one possible improvement to these kinds of integration tasks of DFMA and PDM, it is suggested that the responsibilities for developing DMFA and PDM applications with proper design parameters could be analyzed more deeply between persons working with information exchange, product design, software design, or production machine design.     

Carotenoid Composition of Invertebrates Consumed by Two Insectivorous Bird Species

Dietary carotenoids are important pigments, antioxidants, and immune-stimulants for birds. Despite recent interest in carotenoids in bird ecology, we know surprisingly little about the carotenoid content of invertebrates consumed by birds. We compared carotenoid (lutein, β-carotene, and total) concentrations in invertebrates brought to nestlings by two insectivorous passerines, the great tit, Parus major and the pied flycatcher, Ficedula hypoleuca. We also compared carotenoid levels between environments that were either polluted by heavy metals or were not polluted, because the carotenoid-based plumage color of P. major nestlings is affected by environmental pollution. Lepidopterans were the most carotenoid-rich food items and contained the largest proportion of lutein. There were no differences in carotenoid concentrations in the food items of the two bird species but P. major nestlings obtained more carotenoids from their invertebrate diet than F. hypoleuca nestlings because the P. major diet had a higher proportion of lepidopteran larvae. In polluted areas, P. major nestlings consumed lower levels of dietary carotenoids than in unpolluted areas because of temporal differences in caterpillar abundance between polluted and unpolluted sites. Our study suggests that pollution-related difference in nestling plumage color in P. major is related to varying dietary proportion of lutein-rich food items rather than pollution-related variation in insect carotenoid levels.