Resource management in UAV-assisted MEC: state-of-the-art and open challenges

Wireless Networks - Unmanned aerial vehicles (UAV) have been widely used in various fields because of their high mobility and portability. At the same time, due to the rapid development of...     

Interlayer Engineering of Molybdenum Trioxide toward High‐Capacity and Stable Sodium Ion Half/Full Batteries

Orthorhombic molybdenum trioxide (MoO₃) is one of the most promising anode materials for sodium‐ion batteries because of its rich chemistry associated with multiple valence states and intriguing layered structure. However, MoO₃ still suffers from the low rate capability and poor cycle induced by pulverization during de/sodiation. An ingenious two‐step synthesis strategy to fine tune the layer structure of MoO₃ targeting stable and fast sodium ionic diffusion channels is reported here. By integrating partially reduction and organic molecule intercalation methodologies, the interlayer spacing of MoO₃ is remarkably enlarged to 10.40 Å and the layer structural integration are reinforced by dimercapto groups of bismuththiol molecules. Comprehensive characterizations and density functional theory calculations prove that the intercalated bismuththiol (DMcT) molecules substantially enhanced electronic conductivity and effectively shield the electrostatic interaction between Na⁺ and the MoO₃ host by conjugated double bond, resulting in improved Na⁺ insertion/extraction kinetics. Benefiting from these features, the newly devised layered MoO₃ electrode achieves excellent long‐term cycling stability and outstanding rate performance. These achievements are of vital significance for the preparation of sodium‐ion battery anode materials with high‐rate capability and long cycling life using intercalation chemistry.     

Wetting,infiltration and interaction behavior of CMAS towards columnar YSZ coatings deposited by plasma spray physical vapor

Thermal barrier coatings (TBCs) produced by electron beam physical vapor deposition (EB-PVD) or plasma spray (PS) usually suffer from molten calcium-magnesium-alumino-silicate (CMAS) attack. In this study, columnar structured YSZ coatings were fabricated by plasma spray physical vapor deposition (PS-PVD). The coatings were CMAS-infiltrated at 1250?°C for short terms (1, 5, 30?min). The wetting and spreading dynamics of CMAS melt on the coating surface was in-situ investigated using a heating microscope. The results indicate that the spreading evolution of CMAS melt can be described in terms of two stages with varied time intervals and spreading velocities. Besides, the PS-PVD columnar coating (～100?μm thick) was fully penetrated by CMAS melt within 1?min. After the CMAS attack for 30?min, the original feathered-YSZ grains (tetragonal phase) in both PS-PVD and EB-PVD coatings were replaced by globular shaped monoclinic ZrO₂ grains in the interaction regions.     

A method for rapidly evaluating reliability and predicting remaining useful life using two-dimensional convolutional neural network with signal conversion

Journal of Mechanical Science and Technology - Real-time monitoring and rapid evaluation of bearing operating conditions, especially for the reliability evaluation and remaining useful life (RUL)...     

聚烯烃催化剂硅胶载体的制备和表征

采用并流共沉淀法制备了适用于聚烯烃催化剂的硅胶载体,为减少颗粒的聚集,在制备过程中添加一种表面活性剂。利用透射电子显微镜(TEM)、比表面积测定(BET)和X射线粉末衍射(XRD)法对制备的硅胶载体进行了表征;考察了在制备硅胶载体过程中原料硅酸钠溶液的浓度、溶液pH以及焙烧温度对产物硅胶载体的物理性能的影响。实验结果表明,硅酸钠溶液的浓度影响硅胶的初始粒子的大小,溶液pH直接影响硅酸钠的水解速率,焙烧温度影响硅胶的孔结构和比表面积。当硅酸钠溶液的浓度为0．2mol／L、溶液pH为8-9、反应温度为70℃、焙烧温度为700℃时,硅胶载体的BET比表面积为242．22m2／g、最可几孔径为16．45 nm、堆密度为0．492 1g/mL,与进口硅胶(Silica Gel 955)的物理性能相近。     

深井长裸眼跨隔测试新工艺的应用

为减少勘探费用，缩短施工周期，取全取准各项地质资料，采取中途测试工艺。随着深井中途测试不断增多，特别是跨隔支撑测试具有一定施工风险和难度，要求测试质量不断提高。结合油田生产实际，合理选配了地层测试工具仪表，不断改进测试管串和优化施工设计，经盐22井中途跨隔测试应用，获得成功。     

闪光灯泵浦Nd3+:GGG激光特性研究

用闪光灯泵浦掺钕钆镓石榴石(Nd^3 ：GGG)激光晶体，研究了脉冲宽度0．5ms、1ms、1．5ms和2ms的放电泵浦下激光输出，实验获得了1．92J的最大激光能量．     

室温下Ho∶YAG激光器输出3J的2．1μm激光

根据对２．１μｍ波长Ｃｒ，Ｔｍ，Ｈｏ∶ＹＡＧ激光器的实验研究，详细分析了冷却温度、放电脉冲半宽度和输出镜透过率等因素对激光器的输出的影响     

辐射技术在食品加工中的应用

综述了食品辐射加工的原理及其作用效果，以及该技术在欧美的应用现状及存在的发展障碍。