Damage mechanism in weldment of 2.25Cr-1Mo steel under creep-fatigue loading

The purpose of this study is to clarify damage process of “Type IV cracking” in weldment of a 2.25Cr-1Mo steel and to propose a micro damage prediction method. From continuous observation under a creep-fatigue test, it was found that spherical shape voids initiated and grew on grain boundaries in fine grain region and these voids grow continuously by changing their shape to crack-like. Both spherical and crack-like void growth rate equations were derived from the proposed void growth model. It was indicated that measured void growth rate under the creep-fatigue loading was well predicted by the growth rate equations.     

Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

Feasibility of a 1,400 m Span Steel Cable-Stayed Bridge

This paper describes the feasibility of 1,400 m steel cable-stayed bridges from both structural and economic viewpoints. Because the weight of a steel girder strongly affects the total cost of the bridge, the writers present a procedure to obtain a minimum weight for a girder that ensures safety against static and dynamic instabilities. For static instability, elastoplastic, finite-displacement analysis under in-plane load and elastic, finite-displacement analysis under displacement-dependent wind load are conducted; for dynamic instability, multimodal flutter analysis is carried out. It is shown that static critical wind velocity of lateral torsional buckling governs the dimension of the girder. Finally, the writers briefly compare a cable-stayed bridge with suspension bridge alternatives.     

Thickness estimation of interface films formed on Li1−xCoO2 electrodes by hard X-ray photoelectron spectroscopy

Solid electrolyte interface (SEI) films formed on Li_1−xCoO₂ electrodes were observed with hard X-ray photoelectron spectroscopy (HX-PES). This paper particularly focuses on film thickness estimation using HX-PES with theoretical calculation. The validity of the calculation was proven by experiments using model SEI films. The native film formed on a LiCoO₂ composite electrode was estimated to be LiF with its thickness of 5 nm. Formation of Co (II) species on top of LiCoO₂ was also indicated. Storage of the electrode at 60 °C brought about considerable film growth (30-40 nm) with carbonate compounds formation. SEI film changes during charging of the LiCoO₂ electrode were also examined. The main component in the film was deduced to be LiF or a kind of fluorite, with its thickness decreased during charging. The SEI formation mechanisms are also elucidated.     

Preparation of carbon microparticle assemblies from phenolic resin using an inverse opal templating method

Three-dimensionally (3D) well-ordered carbon microparticle assemblies with different particle morphologies were fabricated by infiltration of phenolic resin solution into SiO₂ inverse opal structures and subsequent carbonization. The effect of the phenolic resin solution concentration and the carbonization temperature on the morphology of the fabricated carbon microparticles was investigated. At a carbonization temperature of 1000 °C, carbon microparticles with interlocked bridges were obtained when the concentration of phenolic resin solution is 40 wt% and hollow carbon microparticles with opened window channels were obtained at a concentration of 30–35 wt%. When the carbonization temperature was decreased to 500 °C, carbon microparticles with interlocked bridges also were observed, even when the phenolic resin concentration was 30 wt%. The structures and properties of the carbon microparticles and their assemblies were characterized using SEM, XRD, and N₂ adsorption.     

Basic information on new regulatory criteria requiring on-site emergency preparedness for accelerator facilities in Japan

For basic information on new regulatory criteria, the dose rate around a thick target bombarded by proton, electron, or carbon beam having incident energy of 10 MeV–50 GeV (per nucleon in case of carbon) was simulated using the PHITS Monte Carlo code. Based on this simulation, the benchmark which is ‘1 Sv/h at 1 m away from the beam line’ assuming 1% beam loss was evaluated, and compared with the criteria in France and Canada. Based on this evaluation, a new regulatory criteria has been established for requiring on-site emergency preparedness for accelerator facilities in Japan, which is required for the ion accelerator beyond the ion beam of 100 MeV/nucleon and 0.5 kW beam power, and the electron accelerator beyond the electron beam of 50 MeV energy and 1 kW beam power.     

Micropatterning of liquid crystalline polyacetylene derivative by using self-organization processes

Side-chain type liquid crystalline polyacetylene, which has mesogenic moieties as side chains, is one of the promising materials for practical applications in the electronics. Micropatterning of the conductive polymer is a significant issue in this field. We show a simple method to fabricate micropatterns of side-chain type liquid crystalline polyacetylene derivative. Under dry condition, stripes patterns and lattice pattern were formed based on the fingering instability and stick-slip motion of the receding meniscus. Honeycomb-patterned polymer film was obtained by casting polymer solution under humid condition. The micropatterns drastically changed by changing solution concentration and preparation conditions.     

Portal-hepatic venous shunt through a portal aneurysm complicated by hepatic encephalopathy and pulmonary hypertension

We report a rare case of portal-hepatic venous shunt through an enormous portal aneurysm complicated by pulmonary hypertension. A 66-year-old woman was admitted to our hospital for hepatic encephalopathy. Chest roentgenography revealed pulmonary hypertension. Computed tomography and ultrasound examination demonstrated a shunt between the portal and hepatic veins through an enormous portal aneurysm. The diagnoses of portal-hepatic venous shunt and pulmonary hypertension were confirmed by hepatic venous catheterization and cardiac catheterization. Pulmonary hypertension might result from the effects of vasoconstrictive agents, which should be metabolized by the liver in normal subjects, passing through the intrahepatic shunt into the lung.     

Ubiquitous Memories: a memory externalization system using physical objects

In this paper we propose an object-triggered human memory augmentation system named “Ubiquitous Memories” that enables a user to directly associate his/her experience data with physical objects by using a “touching” operation. A user conceptually encloses his/her experiences gathered through sense organs into physical objects by simply touching an object. The user can also disclose and re-experience for himself/herself the experiences accumulated in an object by the same operation. We implemented a prototype system composed basically of a radio frequency identification (RFID) device. Physical objects are also attached to RFID tags. We conducted two experiments. The first experiment confirms a succession of the “encoding specificity principle,” which is well known in the research field of psychology, to the Ubiquitous Memories system. The second experiment aims at a clarification of the system’s characteristics by comparing the system with other memory externalization strategies. The results show the Ubiquitous Memories system is effective for supporting memorization and recollection of contextual events.