Photoelectrochemistry of poly(3-methylthiophene), I: Surface morphology and thickness effect

Photocyclovoltammetric experiments with films of poly(3-methylthiophene) under polychromatic light irradiation show a p-type semiconductor behavior in the reduced state, with a flat band potential of 0.18 V. The photocurrent depends on film thickness and surface morphology. Films with different thickness were characterized by scanning electron microscopy, indicating a globular morphology with globule sizes changing according to the charge density used during polymer deposition. The highest photocurrent is observed for the lowest globule diameter. These films were also irradiated with monochromatic light from the electrolyte side and from the substrate side. A higher photocurrent and a photocurrent spectrum matching the absorption spectrum of the reduced form of the polymer is observed on irradiation from the electrolyte side of a 0.7 μm thick film. In contrast, for irradiation from the electrode side, the photocurrent is lower and the spectrum shows a peak at lower energy. These results were interpreted in terms of a delocalized space charge zone, different kinetics for charge transfer and mass transport across the solvent swollen polymer film and different depth of penetration of the light as a function of wavelength.     

STI process steps for sub-quarter micron CMOS

This paper presents Shallow Trench Isolation (STI) process steps for sub-1/4 μ CMOS technologies. Dummy active areas, vertical trench sidewalls, excellent gap filling, counter mask etch step and CMP end point detection, have been used for a 0.18 μm CMOS technology. Electrical results obtained with a 5.5 nm gate oxide thickness show good isolation down to 0.3 μm spacing. Good transistor performances have been demonstrated.     

Use of postconsumer polyethylene in blends with polyamide 6: Effects of the extrusion method and the compatibilizer

Blends of polyamide and high‐density polyethylene show adequate properties for a large range of applications: they are used for the production of filaments, containers, and molding resins. The effect of the addition of 2 wt % of a compatibilizer, maleic anhydride grafted polyethylene, to the blend was studied and compared to the use of postconsumer polyethylene. The samples were extruded with single‐ and twin‐screw extruders with 25, 50, or 75 wt % f polyethylene, and the test specimens, molded by injection, were characterized by stress–strain tests, thermal properties, and morphologies. Processing the blends with postconsumer polyethylene in both extruders improved the mechanical properties in comparison to the blends processed with high‐density polyethylene and the compatibilizer. The morphologies of these blends showed that there was a decrease in the domain size of the disperse phase with the use of the compatibilizer or postconsumer polyethylene. The results indicate that for this blend, postconsumer polyethylene substituted, with advantages, for the necessity of a compatibilizer and the use of the high‐density polyethylene. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Polyamide-6/vegetal fiber composite prepared by extrusion and injection molding

The interest for the use of vegetal fibers as polymers reinforcement has recently increased because of their unique environmental and technological advantages. This work evaluated the use of Curauá fibers in polyamide-6 composites aiming at glass fiber replacement. Fiber content of 20, 30 or 40 wt% and fiber lengths of 0.1 or 10 mm were studied. Fibers were treated with N₂ plasma or washed with NaOH solution, to improve their adhesion to PA-6. Samples with 20 wt% of short or long fibers, with or without pre-treatment, were compounded in two different co-rotating intermeshing twin-screw extruders. These samples were submitted to mechanical and thermal tests. In conclusion, non-dried raw materials improved fiber/matrix interfacial adhesion. Tensile and flexural properties of this composite are better than unfilled, but lower than glass fiber reinforced polyamide-6. However, its impact resistance and heat deflection temperature are similar to the glass fiber reinforced polyamide-6 and its lower density, enable it to replace this latter in specific non-critical applications.     

Photoelectronic and transport properties of polypyrrole doped with a dianionic dye

Polypyrrole (PPy) doped with dodecylsulfate (DS) and an organic dye (indigo carmine, IC) was electrochemically prepared and characterized by Raman spectroscopy and X-ray diffraction (XRD). The photoelectrochemical properties of PPy-DS and PPy-DS-IC in contact with an electrolytic solution containing a redox couple were studied using the theories for the semiconductor ∣ electrolyte interface. Results indicate that the system containing IC presents a higher photocurrent density under polychromatic illumination and faster response time when compared with PPy-DS. This fact was assigned to the formation of molecular-scale paths in PPy-DS-IC. The IC molecules lying perpendicularly between PPy chains, as confirmed by the X-ray analysis, could facilitate the mass transport at the interface and increase the ordering degree to provide better electronic charge transfer in the bulk. Although the photoelectrochemical devices presented here do not present all the properties of inorganic-based devices, we discuss some strategies to enhance the photoelectrochemical properties and response time of conducting polymers used in these type of systems.     

CSDL: a language for cooperative systems design

The aim of a cooperative system is to coordinate and support group activities. Cooperative Systems Design Language (CSDL) is an experimental language designed to support the development of cooperative systems from specification to implementation. In CSDL, a system is defined as a collection of reusable entities implementing floor control disciplines and shared workspaces. CSDL tries to address the difficulties of integrating different aspects of cooperative systems: cooperation control, communication, and system modularization. This paper presents CSDL as a specification language. Basic units are coordinators that can be combined hierarchically. A coordinator is composed of a specification, a body, and a context. The specification defines the cooperation policy; the body controls the underlying communication channels; and the context defines coordinators' interaction in modular systems     

Diagnosability Analysis of a Class of Hierarchical State Machines

This paper addresses the problem of fault detection and isolation for a particular class of discrete event dynamical systems called hierarchical finite state machines (HFSMs). A new version of the property of diagnosability for discrete event systems tailored to HFSMs is introduced. This notion, called L₁-diagnosability, captures the possibility of detecting an unobservable fault event using only high level observations of the behavior of an HFSM. Algorithms for testing L₁-diagnosability are presented. In addition, new methodologies are presented for studying the diagnosability properties of HFSMs that are not L₁-diagnosable. These methodologies avoid the complete expansion of an HFSM into its corresponding flat automaton by focusing the expansion on problematic indeterminate cycles only in the associated extended diagnoser.

Active fault tolerant control of discrete event systems using online diagnostics

The aim of this paper is to deal with the problem of fault tolerant control in the framework of discrete event systems modeled as automata. A fault tolerant controller is a controller able to satisfy control specifications both in nominal operation and after the occurrence of a fault. This task is solved by means of a parameterized controller that is suitably updated on the basis of the information provided by online diagnostics: the supervisor actively reacts to the detection of a malfunctioning component in order to eventually meet degraded control specifications. Starting from an appropriate model of the system, we recall the notion of safe diagnosability as a necessary step in order to achieve fault tolerant control. We then introduce two new notions: (i) “safe controllability”, which represents the capability, after the occurrence of a fault, of steering the system away from forbidden zones and (ii) “active fault tolerant system”, which is the property of safely continuing operation after faults. Finally, we show how the problem can be solved using a general control architecture based on the use of special kind of diagnoser, called “diagnosing controller”, which is used to safely detect faults and to switch between the nominal control policy and a bank of reconfigured control policies. A simple example is used to illustrate the new notions and the control architecture introduced in the paper.     

On some properties of quasi-MV algebras and \sqrt{^{\prime}} quasi-MV algebras. Part II

The present paper is a sequel to Paoli F, Ledda A, Giuntini R, Freytes H (On some properties of QMV algebras and QMV algebras, submitted). We provide two representation results for quasi-MV algebras in terms of MV algebras enriched with additional structure; we investigate the lattices of subvarieties and subquasivarieties of quasi-MV algebras; we show that quasi-MV algebras, as well as cartesian and flat quasi-MV algebras, have the amalgamation property.     

Implicit fault-tolerant control: application to induction motors

In this paper we propose an innovative way of dealing with the design of fault-tolerant control systems. We show how the nonlinear output regulation theory can be successfully adopted in order to design a regulator able to offset the effect of all possible faults which can occur and, in doing so, also to detect and isolate the occurred fault. The regulator is designed by embedding the (possible nonlinear) internal model of the fault. This idea is applied to the design of a fault-tolerant controller for induction motors in presence of both rotor and stator mechanical faults.