Mechanisms of orientational and photoelastic birefringence generation of methacrylates for the design of zero–zero‐birefringence polymers

The intrinsic birefringence Δn⁰ and photoelastic coefficient C of poly(methyl methacrylate), poly(2,2,2‐trifluroethyl methacrylate), poly(phenyl methacrylate), and poly(2,2,3,3,3‐pentafluorophenyl methacrylate) were determined. We categorized these methacrylate polymers into four birefringence‐types, even though their molecular structures differed only by the substituents on the side chains. Based on the results of Δn⁰ and C, novel polymers that exhibit neither orientational nor photoelastic birefringence, i.e., zero–zero‐birefringence polymers, were designed and synthesized by quaternary copolymerization system. Furthermore, we confirmed that the mechanisms of orientational birefringence and photoelastic birefringence generation were different in these methacrylate polymers. The conformation of the repeat unit of the polymers was nearly constant during the generation of orientational birefringence. In contrast, the conformation of the repeat unit of the polymers changed during the generation of photoelastic birefringence in the glassy state. These findings demonstrated the reasonability of evaluating orientational and photoelastic birefringence separately, as well as the adequacy of the classification of polymers into four birefringence‐types. Given these results and the fact that zero–zero‐birefringence polymers could be prepared successfully by four‐birefringence type monomers, we demonstrated the reasonability of the method for designing the zero–zero‐birefringence polymers. POLYM. ENG. SCI., 55:1330–1338, 2015. © 2015 Society of Plastics Engineers     

A 1-Gb/s/pin 512-Mb DDRII SDRAM using a digital DLL and a slew-rate-controlled output buffer

A 1-Gb/s/pin 512-Mb DDRII SDRAM has been developed using a digital delay-locked loop (DLL) and a slew-rate-controlled output buffer. The digital DLL has a frequency divider for DLL input, performs at an operating frequency of up to 500 MHz at 1.6 V, and provides internal clocking with 50% duty-cycle correction. The DLL has a current-mirror-type interpolator, which enables a resolution as high as 14 ps, needs no standby current, and can operate at voltages as low as 0.8 V. The slew-rate impedance-controlled output buffer circuit reduces the output skew from 107 to 10 ps. This SDRAM was tested using a 0.13-/spl mu/m 126.5-mm/sup 2/ 512-Mb chip.     

Measurement of self-diffusion coefficients in Li ionic conductors by using the short-lived radiotracer of 8Li

For the effective use of short-lived radioactive beams, soon to be available at the Tokai Radioactive Ion Accelerator Complex, the authors have developed a radiotracer method for diffusion studies in solids. The experimental test was performed by the measurement of the diffusion coefficients of Li in a sample of the compound βLiAl using an α-emitting radiotracer of ⁸Li (T_1/2=0.84 s). It was found that the time-dependent yields of the α particles from the diffusing ⁸Li that was initially implanted in the sample could be used as a measure of the diffusivity of the tracer in a nondestructive way. The method was applied to measure the self-diffusion coefficients of Li in βLiGa, and for investigating how the Li diffusion in the Li ionic conductors is affected by the concentration of atomic defects (i.e., the existence of the atomic vacancies of Li and the defects in Ga sites that are replaced by Li).     

Constant-phase-mode operation of the light-addressable potentiometric sensor

The constant-phase-mode operation of the light-addressable potentiometric sensor (LAPS) is proposed and demonstrated. In this new operation mode, the temporal change and the spatial distribution of the analyte concentration are recorded in the form of the bias voltage applied to the LAPS sensor plate, which is servo-controlled to maintain the phase of the photocurrent at a constant value with respect to the light modulation. The constant-phase-mode LAPS is advantageous for its wider measurement range and reduction of artifacts.     

Damage to seagrass and seaweed beds in Matsushima Bay,Japan, caused by the huge tsunami of the Great East Japan Earthquake on 11 March 2011

Damage to seagrass and seaweed beds caused by the huge tsunami of the Great East Japan Earthquake on 11 March 2011 was investigated in Matsushima Bay, Miyagi Prefecture, Japan, by comparing satellite images taken before the tsunami in November 2009 and after the tsunami in May 2011. The results showed that the tsunami destroyed 220 ha of seagrass and seaweed beds, from 320 ha in 2009 to 100 ha just after the tsunami. Zostera marina beds on the sandy and muddy bottom were rather severely damaged compared with brown seaweed beds of Sargassum horneri on the rocky substrate. Substrates of the beds and directions of the tsunami seem to be responsible for the magnitude of the damage to the beds. Maps of the spatial distributions of the beds before and after the tsunami can provide information for the restoration of seagrass and seaweed beds as natural infrastructures of coastal fisheries resources.     

A novel bistable reflective display using quick‐response liquid powder

Abstract— We have developed new powder materials that exhibit liquid behavior, which can lead to the realization of novel bistable and reflective displays having paper‐white appearance, high contrast, and quick response. Two types of display were demonstrated, one had 160 × 160 array of pixels and the other had 320 × 320 in a 3.1‐in.‐diagonal viewable image size corresponding to 66 and 132 dpi, respectively. These displays were driven by passive‐matrix addressing. The displays showed a reflectivity of more than 41%, a contrast more than 1:10, and a pixel response time of less than 0.2 msec. The seven‐segment display for use in clocks was also demonstrated.     

Effect of thermal crosslinking on the properties of sulfonated poly(phenylene sulfone)s as proton conductive membranes

The synthesis and characterization of crosslinked aromatic polymer membranes with high ion exchange capacity (IEC) values are reported. Through aromatic nucleophilic substitution polycondensation and the subsequent sulfonation reaction, the highly sulfonated polymers SPPSU‐2S and SPPSU‐4S with high molecular weight (M_n = 138–145 kDa, M_w = 200–279 kDa) and well‐defined structures were synthesized. By solution casting and thermal annealing treatment, flexible crosslinked membranes with high solvent insolubility were obtained. The membranes exhibited mechanical and chemical stability as confirmed by dynamic mechanical analysis (DMA) and conductivity measurement. The crosslinked SPPSU‐4S membrane with IEC = 3.20 meq/g showed the highest proton conductivity of 0.163 S/cm at 120 °C, 90% RH, and improved thermal stability compared with its precursor (uncrosslinked) membrane. The results show that simple annealing method could improve significantly membranes properties of highly sulfonated aromatic polymers. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44218.