Large eddy simulation of free-shear flows using an algebraic model

Large eddy simulation of the free-shear flows has been performed using an algebraic subgrid stress model. The test cases considered are the temporal planar jet and mixing layer. The results are compared with that of the Smagorinsky, dynamic Smagorinsky, mixed models and the DNS data. For the mean flow quantities none of the models perform exceptionally better over the others. However, both the algebraic and mixed models predict better statistics for the turbulent quantities than the linear models. The results also demonstrate the capability of the algebraic model in depicting backscatter of energy explicitly, which is consistent in both the cases considered.     

Countercurrent water-heating system with a heat exchanger in a solar energy collector loop

The counter current heat exchanger theory with periodic inlet temperatures has been applied to analyze the thermal performance of a water heating system. The theoretical results obtained are in agreement with the experimental data reported in the literature.     

Prediction of burning rate of coal in fluidized-bed combustion

A theory has been proposed to evaluate the burning rate of a single carbon particle in a continuously operated coal-fired fluidized bed. Experimental verification was carried out in a laboratory scale 200 mm × 200 mm combustor. The burning rate increases with the increase of the fluidization velocity and the size of the bed material. The predicted data on burning rate agree fairly well with the experimental values. The gas concentration in the bed and freeboard has also been measured and it is seen that the consumption of oxygen mostly takes place in the bed.     

Microcellular foaming of poly(lactic acid) branched with food-grade chain extenders

This study evaluated the effectiveness and efficiency of two food-grade multifunctional epoxies chain extenders (CE) in branching PLA and improving its foamability. Both CE grades were effective in branching PLA causing increased end mixing torque, shear, elongational viscosities, molecular weight but decreased crystallinity of poly(lactic acid) (PLA) with CE content, due to chain entanglements. CE with low epoxy equivalent weight (EEW) was more efficient than the counterpart with high EEW due to its high reactivity. Neat PLA foams showed poor cell morphology with areas without nucleated cells and had a low expansion, owing to its low elongational viscosity. By contrast, there was a considerable change in the morphology of the PLA foam structure caused by its branching. Chain-extended PLA foams had uniform cell morphology with a high void fraction (up to ~85%) and expansion ratio (an eightfold expansion over unfoamed PLA) due to their high elongational viscosities, suggesting that melt properties of branched PLA were appropriate for optimum cell growth and stabilization during foaming. Overall, CE with low EEW was the most effective grade and 0.25% the optimum content that provided appropriate melt viscosity to produce PLA foams with a homogeneous structure, fine cells, high void fraction, high volume expansion ratio, and cell-population density.     

Surface modification of AFM silicon probes for adhesion and wear reduction

Tip wear of silicon probes used for an atomic force microscope (AFM) is a critical issue. Wear can result in an increase of tip radius and adhesion between tip and sample, thus reducing the image resolution and introducing artifacts. In order to reduce adhesion, friction, and wear so as to reduce tip related artifacts, liquid lubricant (Z-TETRAOL), self-assembled monolayers (pentafluorophenyltriethoxysilane (PFPTES)), and fluorocarbon polymer (Fluorinert™) were applied on the silicon probe. A comprehensive investigation of adhesion, friction, and wear of the uncoated/coated tips in both ambient air and various humidity levels as well as the influence of the coatings on the image resolution was performed. Experiments showed that the coatings reduced the adhesion, friction, and wear of the silicon tip, improved the initial image resolution, and exhibited less deterioration as compared to that of uncoated tip in the long-term test.     

Nanotribological characterization of human hair and skin using atomic force microscopy

Healthy hair and skin is highly desired. Characterization of their morphological, frictional, and adhesive properties (tribological properties) is essential to enhance understanding of hair and skin and to advance the science. Literature on the tribological characterization of hair and skin is scarce to date. The paper presents nanotribological data and analysis on hair (Caucasian, Asian, and African hair at virgin, chemo-mechanically damaged, and treated conditions) and synthetic hair and skin, as well as roughness data of human skin replica. Roughness statistics are presented to characterize the vertical and spatial surface parameters. Average coefficient of friction values were determined for each ethnicity and hair type, and are discussed. The directionality dependence of friction is also discussed. Magnitude and spatial distribution of adhesive force are used to estimate thickness and distribution of the conditioner film.     

Electrostatic ion trap and Fourier transform measurements for high-resolution mass spectrometry

We report on the development of an electrostatic ion trap for high-resolution mass spectrometry. The trap works on purely electrostatic fields and hence trapping and storing of ions is not mass restrictive, unlike other techniques based on Penning, Paul, or radio frequency quadrupole ion traps. It allows simultaneous trapping and studying of multiple mass species over a large mass range. Mass spectra were recorded in "dispersive" and "self-bunching" modes of ions. Storage lifetimes of about 100 ms and mass resolving power of about 20,000 could be achieved from the fifth harmonic Fourier transform spectrum of Xe ions recorded in the self-bunching mode.     

Enantioseparations in Achiral Environments and Chromatographic Systems

Since the very first resolution of racemic tartaric acid by Pasteur, the importance of resolution and methodology has been on a path of continuous understanding and expansion. The science and chemistry of achieving such targets has changed a lot. The advent of chromatography changed the direction by involving synthetic, semisynthetic, or naturally occurring chiral materials for a direct approach to resolution, where rapid and reversible association occurs to form diastereomers with different stabilities and partition coefficients responsible for overall enantioseparation. It has now reached a stage where the separation of excess enantiomers from nonracemic mixtures has been achieved in a totally achiral environment, which does not appear to be in line with the prevalent concepts of basic stereochemistry. Caution should be exercised when enantiomerically enriched mixtures – obtained by enantioselective synthesis – are chromatographed for purification in preparative organic synthesis.     

Augmented photoelectrochemical response of CdS/ZnS quantum dots sensitized hematite photoelectrode

A visible light active and stable photoelectrode has been developed by depositing a passivating layer of ZnS QDs on CdS QDs sensitized hematite photoelectrode (Hematite‐CdS/ZnS) for PEC generation of hydrogen. Photoelectrochemical properties, in terms of stability and efficiency, have been investigated on the various hematite photoelectrodes sensitized with CdS QDs and CdS/ZnS QDs by varying number of SILAR cycles. I–V characteristics show that two layers of ZnS QDs deposited over three layers of CdS could enhance PEC response of hematite and efficiency by a factor of 3 and 11 respectively. Chronoamperometry measurement ensures that after adding a layer of ZnS QDs, CdS sensitized hematite film turns out to be a stable photoelectrode in the electrolyte. Prepared photoelectrodes have been characterized by XRD, SEM, HRTEM and UV–Vis spectrophotometer for various structural, morphological and optical properties to analyze PEC results. Mott–Schottky analysis and incident photon to current conversion efficiency (IPCE) measurements of sensitized hematite photoelectrode supported the improved PEC response of CdS/ZnS QDs sensitized hematite thin films. Copyright © 2016 John Wiley & Sons, Ltd.