Growth of Potassium Titanate Fibers in Flowing N2 Gas

The length of potassium titanate fibers produced by several conventional methods averages 50 μm, with a maximum of 100 μm. Extremely long fibers (most >1000 μm long) were obtained by calcination in N₂ gas flowing at 5.2×10^-4 m/s.     

InxGa1−xAs ohmic contacts to n-type GaAs with a tungsten nitride barrier

Significant reduction of the contact resistance of In_0.7Ga_0.3As/Ni/W contacts (which were previously developed by sputtering in our laboratory) was achieved by depositing a W₂N barrier layer between the Ni layer and W layer. The In_0.7Ga_0.3 As/Ni/W₂N/W contact prepared by the radio-frequency sputtering technique showed the lowest contact resistance of 0.2 Ωmm after annealing at 550°C for 10 s. This contact also provided a smooth surface, good reproducibility, and excellent thermal stability at 400°C. The polycrystalline W₂N layer was found to suppress the In diffusion to the contact surface, leading to improvement of the surface morphology and an increase in the total area of the In_xGa−As between metal and the GaAs substrate. These improvements are believed to reduce the contact resistance.     

A video DSP with a macroblock-level-pipeline and a SIMD typevector-pipeline architecture for MPEG2 CODEC

A video DSP with macroblock-level-pipeline and a SIMD type vector-pipeline architecture (VDSP2) has been developed, using 0.5 μm triple-layer-metal CMOS technology. This 17.00 mm×15.00 mm chip consists of 2.5 M transistors, and operates at 100 MHz. The real-time encoder and decoder specified in the MPEG2 main profile at the main level can be realized with two VDSP2's and a motion estimation (ME) unit, and one VDSP2 respectively, at an 80 MHz clock rate, with a total power dissipation of 4.2 W at 3.3 V     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

MiR-10a in Pancreatic Juice as a Biomarker for Invasive Intraductal Papillary Mucinous Neoplasm by miRNA Sequencing

New biomarkers are needed to further stratify the risk of malignancy in intraductal papillary mucinous neoplasm (IPMN). Although microRNAs (miRNAs) are expected to be stable biomarkers, they can vary owing to a lack of definite internal controls. To identify universal biomarkers for invasive IPMN, we performed miRNA sequencing using tumor-normal paired samples. A total of 19 resected tissues and 13 pancreatic juice samples from 32 IPMN patients were analyzed for miRNA expression by next-generation sequencing with a two-step normalization of miRNA sequence data. The miRNAs involved in IPMN associated with invasive carcinoma were identified from this tissue analysis and further verified with the pancreatic juice samples. From the tumor-normal paired tissue analysis of the expression levels of 2792 miRNAs, 20 upregulated and 17 downregulated miRNAs were identified. In IPMN associated with invasive carcinoma (INV), miR-10a-5p and miR-221-3p were upregulated and miR-148a-3p was downregulated when compared with noninvasive IPMN. When these findings were further validated with pancreatic juice samples, miR-10a-5p was found to be elevated in INV (p = 0.002). Therefore, three differentially expressed miRNAs were identified in tissues with INV, and the expression of miR-10a-5p was also elevated in pancreatic juice samples with INV. MiR-10a-5p is a promising additional biomarker for invasive IPMN.     

Thermodynamic study of the phase equilibria in the Sn−Ti−Zn ternary system

The Sn−Ti−Zn ternary phase diagram has been constructed using the CALPHAD technique. The Ti−Zn binary system phase boundaries were determined using differential scanning calorimetry and the solid-liquid diffusion couples method. In addition, the formation energy of some stoichiometric compounds was obtained using first-principle band energy calculations. For the ternary system, some alloys were prepared by equilibration at 600 or 700 °C, and the compositions of the precipitates were analyzed using electron probe microanalysis. Thermodynamic assessment of the Ti−Zn and Sn−Ti−Zn systems was performed based on the experimental information and by adopting reported values of the thermodynamic properties of the Sn−Zn and Sn−Ti binary systems. Microstructural observation showed that Sn₃Ti₅Zn₁₂ exists in the ternary system. Seven types of invariant reaction on the Sn-rich liquidus surface of the ternary system are predicted by the phase diagram calculations. The ternary eutectic point falls at 0,0009 mass% Ti and 8.69 mass% Zn, at T=192.40°C, which is slightly lower than the calculated eutectic point of Sn−Zn binary alloy (T=192.41°C). Based on these results, a nonequilibrium solidification process using the Scheil model was simulated. This paper was presented at the International Symposium on User Aspects of Phase Diagrams, Materials Solutions Conference and Exposition, Columbus, Ohio, 18–20 October, 2004.     

Local disturbances preceding a running crack front in a viscoelastic solid

The local disturbances ahead of a running crack front in a viscoelastic solid were measured through noncontact electro-optical tools. It was observed that the very high local strain rate up to 200/sec exists even in the present quasistatic loading case. It may be concluded that the running crack propagation velocities, not the conventional average strain rates ranging from about 10^?4/sec to 10^?2/sec, govern the local disturbances, as the crack propagation velocities always exceed 200m/sec for both average strain rates, while the local strain rates observed do not show much differences between both average strain rate cases.     

Novel synthesis of microcrystalline titanium(IV) oxide having high thermal stability and ultra-high photocatalytic activity: thermal decomposition of titanium(IV) alkoxide in organic solvents

Thermal decomposition of titanium(IV) tetra-tert-butoxide (TTB) in inert organic solvents at 573 K yielded microcrystalline anatase (titanium(IV) oxide, TiO₂) powders with a crystallite size of ca. 9 nm and a surface area of <100 m² g^-1. Primary and secondary alkoxides of titanium(IV), however, were not decomposed under similar conditions, indicating that the thermal stability of C-O bonds in the alkoxides was a decisive factor for their decomposition. The TiO₂ prepared from TTB by this manner was thermally stable upon calcination in air and retained high surface area of ca. 100 m² g^-1 even after calcination at 823 K. The as-prepared TiO₂ powders, without calcination, exhibited much higher rate of carbon dioxide formation than any other active photocatalysts such as Degussa P-25 and Ishihara ST-01 in the photocatalytic mineralization of acetic acid in aerated aqueous solutions. The higher activity of the present TiO₂ photocatalysts is attributed to both high crystallinity and large surface of the present product. The calcination of the as-prepared TiO₂ in air reduced the photocatalytic activity, but it was still higher than the other commercially available TiO₂'s. This revised version was published online in July 2006 with corrections to the Cover Date.     

Reaction products of α-tocopherol with methyl linoleate-peroxyl radicals

α-Tocopherol was reacted with methyl linoleateperoxyl radicals at 37°C. The peroxyl radicals were generated by the reaction of methyl linoleate with a free radical initiator, 2,2′-azobis(2,4-dimethylvaleronitrile). The primary products of α-tocopherol with methyl linoleate-peroxyl radicals were isolated by reversephase and normal-phase high performance liquid chromatography (HPLC), and their structures were characterized by ultraviolet (UV), infrared (IR),¹H and¹³C nuclear magnetic resonance (NMR) and mass spectrometry (MS). There were four stereoisomers of methyl 13-(8a-peroxy-α-tocopherone)-9(Z),11(E)-octadecadienoate and four stereoisomers of methyl9-(8a-peroxy-α-tocopherone)-10(E),12(Z)-octadecadienoate.     

A manufacturing XML schema definition and its application to a data management system on the shop floor

Digitization for sharing knowledge on the shop floor in the machinery industry has been given much attention recently. To help engineers use digitization practically and efficiently, this paper proposes a method based on manufacturing case data that has a direct relation to manufacturing operations. The data are represented in XML schema, as it can be easily applied to Web-based systems on the shop floor. The definitions were made for eight manufacturing methods including machining and welding. The derived definitions consist of four divisions of metadata, work-piece, process and evaluation. Three divisions except for the “process” division are common to the manufacturing methods. The average number of elements for a manufacturing method is about 200. The represented schema is also used to convey knowledge such as operation standards and manufacturing troubleshooting on the shop floor. Using the definitions, a data management system is developed. It is a Web-based Q&A system, in which the engineers specify the manufacturing case data mainly by selecting from the candidates. Then, the system fills in the blank portions and/or shows messages to help complete the case data. The proposed method is evaluated through practical scenarios of arc welding and machining.