电压对电刷镀三价铬镀层性能的影响

在45钢表面电刷镀得到三价铬镀层,镀液组成和工艺条件为:Cr2(SO4)36H2O 0.4 mol/L,甲酸铵0.5 mol/L,氨基乙酸0.5 mol/L,H3BO30.6 mol/L,NaH2PO2 H2O 0.3 mol/L,pH=1.5,温度50°C,镀笔移动速率15 cm/s。研究了电压对镀铬层显微结构、表面粗糙度、厚度、显微硬度和耐磨性的影响。随电压增大,镀层厚度增大,显微硬度和耐磨性均先提高后降低。电压为14 V时,镀层的表面平整,粗糙度为2.387μm,显微硬度为602 HV,耐磨性最好。     

Robust3D: a robust 3D face reconstruction application

In the process of reconstructing a historical event such as a rock concert only from video, the reconstruction of faces and expressions of the musicians is obviously important. However, in the process of rebuilding appearance, because of the low quality of the video of the recorded concert, the result of the reconstruction may be far from the real appearance. In this paper, a robust 3D face reconstruction application is described that can be applied to a video recording. The application first uses DeblurGAN program to run anti-ambiguity calculation and removes the ambiguity in the concert video. Then, the super-resolution program is used to enlarge every frame of the concert video by four times, thus making every frame of the video clearer. Finally, the 3D faces are obtained after 3D reconstruction of the processed video frames via the 3DMM_CNN program.

     

Theoretical investigation of solvent effects on the selective hydrogenation of furfural over Pt(111)

It was well known that solvent effect plays a very important role in the catalytic reaction. There are many theoretical studies on the solvent effect in homogeneous catalysis while there are few theoretical studies on the solvent effect in the heterogeneous catalytic reaction and there has been no work to investigate the solvent effect on furfural transformation in heterogeneous catalysis. In the present work, both the density functional calculations and the microkinetic analysis were performed to study the selective hydrogenation of furfural over Pt(111) in the presence of methanol as well as toluene and compared with that in the gas condition. The present results indicated that the methanol can enhance the adsorption strength of furfural and other oxygen-containing reaction species due to its relatively strong polarity properties and this can be a main reason for solvent-induced high activity and selectivity. Another reason is that reaction paths study showed that the presence of methanol solvent makes the dehydrogenation of furfural less thermochemical due to the fact that furfural is more stabilized than that of dehydrogenation species, and methanol also has an inhibition effect on the dehydrogenation of furfural in the kinetic aspect, and further energetic span theory proves highest activity and selectivity for hydrogenation in methanol solvent of vapor, methanol and toluene. Moreover, microkinetic model simulation demonstrated that the activity and selectivity of hydrogenation in methanol is both higher than that in vapor and toluene. The much higher activity in methanol is due to the stabilized adsorbed reactants in the surface, which leads to a higher surface coverage of furfural. It might be proposed based on the present work that a solvent with relatively strong polarity may be favorable for the high selective hydrogenation of furfural.     

A highly active composite electrocatalyst Ni–Fe–P–Nb2O5/NF for overall water splitting

This work demonstrates a facile Nb₂O₅-decorated electrocatalyst to prepare cost-effective Ni–Fe–P–Nb₂O₅/NF and compared HER & OER performance in alkaline media. The prepared electrocatalyst presented an outstanding electrocatalytic performance towards hydrogen evolution reaction, which required a quite low overpotential of 39.05 mV at the current density of ?10 mA cm^?2 in 1 M KOH electrolyte. Moreover, the Ni–Fe–P–Nb₂O₅/NF catalyst also has excellent oxygen evolution efficiency, which needs only 322 mV to reach the current density of 50 mA cm^?2. Furthermore, its electrocatalytic performance towards overall water splitting worked as both cathode and anode achieved a quite low potential of 1.56 V (10 mA cm^?2).     

Chromium evaporation and oxidation characteristics of alumina-forming austenitic stainless steels for balance of plant applications in solid oxide fuel cells

The chromium (Cr) evaporation behavior of several different types of iron (Fe)-based AFA alloys and benchmark Cr₂O₃-forming Fe-based 310 and Ni-based 625 alloys was investigated for 500 h exposures at 800 °C to 900 °C in air with 10% H₂O. The Cr evaporation rates from alumina-forming austenitic (AFA) alloys were ~5 to 35 times lower than that of the Cr₂O₃-forming alloys depending on alloy and temperature. The Cr evaporation behavior was correlated with extensive characterization of the chemistry and microstructure of the oxide scales, which also revealed a degree of quartz tube Si contamination during the test. Long-term oxidation kinetics were also assessed at 800 to 1000 °C for up to 10,000 h in air with 10% H₂O to provide further guidance for SOFC BOP component alloy selection.     

Recent Development of Photothermal Agents (PTAs) Based on Small Organic Molecular Dyes

Photothermal therapy (PTT) has attracted great attention due to its noninvasive and effective use against cancer. Various photothermal agents (PTAs) including organic and inorganic PTAs have been developed in the last decades. Organic PTAs based on small-molecule dyes exhibit great potential for future clinical applications considering their good biocompatibility and easy chemical modification or functionalization. In this review, we discuss the recent progress of organic PTAs based on small-molecule dyes for enhanced PTT. We summarize the strategies to improve the light penetration of PTAs, methods to enhance their photothermal conversion efficiency, how to optimize PTAs’ delivery into deep tumors, and how to resist photobleaching under repeated laser irradiation. We hope that this review can rouse the interest of researchers in the field of PTAs based on small-molecule dyes and help them to fabricate next-generation PTAs for noninvasive cancer therapy.     

Amine-containing olefin copolymer with CO2-switchable oil absorption and desorption

Global decrease in crude oil resources and frequent crude oil leaks cause the energy crisis and ecological pollution. The absorption and release of leaked crude oil through absorption materials are a necessary process for environmental protection and recycling. In this article, a CO₂-responsive olefin copolymer was obtained by copolymerization of styrene and an amine-containing olefin monomer. The structure of resultant copolymer was characterized by FTIR; thermal properties and CO₂-responsive morphology changes were determined by DSC/TGA and SEM, respectively. Copolymers had certain absorption capacity for toluene with absorption rate up to 180.0%. The absorbed toluene could be released upon CO₂ stimulation with desorption rate up to 84.6%. The CO₂-responsive copolymer could be regenerated through a simple heating process and showed stable absorption–desorption performance even after being recycled for 4 times. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47439.     

Intelligent Information‐Centric Networking routing scheme under imprecise information

Information‐Centric Networking (ICN) has been accepted to overcome some weaknesses of the current Internet architecture, showing that “what is being exchanged” is more important than “who are exchanging information.” Given the inadequate considerations on Quality of Service (QoS) and energy saving in ICN routing, we propose in this paper a routing algorithm to enhance the two aspects. At first, on one hand, Cauchy distribution is used as a fuzzy model to evaluate users' QoS requirements, such as bandwidth, delay, and error rate; on the other hand, we formulate energy saving problem to evaluate the green quality of routing algorithm. Then, we design a link selection approach by considering QoS and energy saving, which belongs to a multi‐objective decision problem resolved by intelligent drops algorithm. Finally, we implement the proposed algorithm and compare it with the famous adaptive forwarding mechanism in terms of some significant metrics, and the experimental results reveal that the proposed algorithm is more efficient.     

Transparent niobate glass-ceramics for optical limiting

The construction of nonlinear optical materials featuring asymmetric transmission of light is of great technological importance for various applications, including optical switching and optical power limiting. A significant challenge is the scalable fabrication of material candidates with good photochemical stability, high optical transmittance, and excellent optical limiting performance. Here, we present a nanocrystallization avenue for constructing hybrid optical limiting materials that exhibit ultrafast and robust optical limiting performance. The experimental results show that the controllable relaxation of a niobate glass may lead to the clustering of Nb-O units and contracting of the bandgap. It results in the notable improvement in nonlinear optical properties, including the enhanced saturation irradiance (380 GW/cm²), doubly increased nonlinear coefficient, and decreased limiting threshold (200 GW/cm²). Our results suggest a promising material that exhibits promising applications for protecting eyes and sensitive components from laser-induced damage.     

基于步冷试验的2.25Cr-1Mo-0.25V钢母材及焊缝回火脆化研究

对原始态、步冷态、脱脆态和脱脆步冷态2.25Cr-1Mo-0.25V钢母材及焊缝冲击试验结果进行分析,得到了母材和焊缝在不同状态下的韧脆转变温度vTr54.2和FATT以及脆化度ΔvTr54.2和ΔFATT。试验结果表明,步冷试验之后,母材发生较低程度脆化或脱脆现象,但是脆化度或脱脆度较低,表明母材具有良好的抗回火脆化性能;经脱脆试验后,母材和焊缝都发生较高程度的脱脆,表明材料的脆化主要是由于回火脆化引起的,脱脆试验使得材料的韧脆转变温度降低;脱脆步冷试验后,焊缝发生较高程度的脆化,焊缝对脱脆步冷试验的敏感性较高,脱脆步冷试验有效促进了焊缝的脆化。在相同脆化条件下,母材的脆化敏感性低于焊缝,焊缝更易发生脆化。