地下埋藏式钢岔管抗外压稳定性分析

考虑了钢岔管与混凝土垫层的初始缝隙和初始几何缺陷,给出了一套地下埋藏式钢岔管抗外压稳定性的三维有限元分析和求解方法。采用该方法分析某工程实例,将其成果与阿氏公式计算的结果进行了比较,证明了该方法的可行性,并得到一些对工程设计有参考价值的成果。     

2.0 Mt/a渣油加氢脱硫装置新氢压缩机性能标定

介绍了中国石化茂名分公司 2 .0Mt/a渣油加氢脱硫装置中的 4M80 30 /2 2 2 0 0 BX型新氢压缩机的特点、技术特征及标定情况。采用国际通用标准对压缩机气体组成、容积流量、轴功率、进排气压力和进排气温度等指标进行了测定。标定表明 ,该机组设计方案合理 ,运转平稳 ,性能指标达到设计要求 ,较好的满足了工艺操作的需要     

Optimal Layout of Displacement Measurements for Parameter Identification Process in Geomechanics

This paper focuses on designing the optimal layout of measurements for parameter identification problems in geomechanics, which are usually based on in situ displacements. The existence, uniqueness, and stability of the solution from the parameter identification process are thoroughly discussed. Based on these understandings of the problem, two algorithms are proposed as a means of automatically generating the optimal measurements. The validity of these algorithms is first proved by some academic examples, then these algorithms are applied to the Munich subway tunnel project. Good results are observed there.     

网络存储的发展历程及新兴的iSCSI

目前SAN和NAS存储正在迅速发展，DAS的生存空间越来越小。今天超过1／3的存储是网络化的，如果不是因为FC的高成本和复杂性．这个数字还会更大。iSCSI是IETF一种新的标准协议．它将SCSI命令压缩到TCP／IP包．使数据块在IP网络上传播。和FC-SAN相比．高速千兆iSCSI耙SCSI、以太网和TCP／IP结合起来，具有许多优势．如建立在稳定和熟悉的标准上；较低的总拥有成本，安装和维修费用很低；较高程度的可操作性，减少了异构网络和电缆．使用一般的以太网交换机而不是特殊的FC交换机；等等。     

Tracking non-rigid objects in clutter background with geometricactive contours

A new variational framework of geometric active contours to track multiple non-rigid moving objects in the clutter background is presented. Incorporating motion edge information, it consists of motion detection and tracking stages. The results of experiments are promising and demonstrate the validity of the proposed framework     

极压聚脲基润滑脂在CSP薄板坯连铸机上的应用

根据CSP薄板坯连铸机的工况特点，基于合理润滑的原则，论述了JZEP极压聚脲基润滑脂在CSP薄板坯连铸机上的成功应用。     

模拟输液器的热解特性

建立非化学计量平衡模型，根据Gibbs最小自由能原理对医疗垃圾中的典型组分输液器进行平衡分析，根据分析结果拟合出产物分布的计算公式。通过危险废物热解焚烧多功能试验台进行试验，试验结果验证了计算公式的可靠性，从而通过公式可直接预测医疗垃圾中典型组分输液器热解后的各产物百分含量。     

多杀菌素的高效液相色谱法测定

采用高效液相色谱法对Saccharpolyspora spinasa发酵液中多杀菌素含量进行测定。本方法的相对标准偏差为0．11％。变异系数为0．15%．线性相关系数为0．99916．平均回收率为96.94％。     

气固两相流中一种抗磨新方法的数值验证

The present paper intends to introduce a new method for reducing bends erosion from particles impacts:the ribbed bend erosion protection method. Ribs are evenly fixed in the range of 20°-80° on the inner-wall of inside 90° bend and the bend (including ribs) is made of medium carbon steel. Three-dimensional numerical work is performed and the result shows satisfactory agreement with the experimental measurement. Numerical simulation studies the characteristics of axial gas flow along the bend and secondary flow at cross section. Detailed analyses involving the impact velocity and incidence angle of particle- metal (either particle-rib or particle-duct) impact unveil the mechanism of the anti- erosion effect. As a result, predications achieve that the average erosion rate of the ribbed bends is only a third of the bare bend under test conditions and rectangle ribs possess higher anti-erosion effect than square ribs, while the wear distribution pattern remains unchanged after adding ribs onto the bend. All results confirm that the ribbed bend erosion protection method is a simple and effective method for reducing bends erosion from particles impacts.     

转盘反应器固定米根霉的L－乳酸发酵

研究了米根霉的固定化方法，研制了用吸附法固定米根霉的生物转盘反应器，考察了在该反应器中培养基组成及其它操作条件对Ｌ－乳酸发酵的影响。实验结果表明，应用吸附法固定化的米根霉及生物转盘反应器进行Ｌ－乳酸发酵具有发酵速率快，Ｌ－乳酸得率高及既能用于连续发酵又能用于间歇发酵等优点