Ca-Mg-Al复合氧化物催化尿素与1,2-丙二醇制碳酸丙烯酯

采用共沉淀法制备了系列Ca-Mg-Al复合氧化物催化剂，通过对沉淀剂配比、沉淀液pH值及焙烧温度等制备条件的考察，得到以Na₂CO₃为沉淀剂、pH=9.5、850℃下焙烧4h制备的Ca-Mg-Al催化活性最高。在 n(PG)∶n(urea)=1.5∶1、反应温度为145℃、绝压20kPa、反应时间4h、催化剂用量为尿素质量的5%时，碳酸丙烯酯收率达到84.6%。采用XRF、XRD、NH₃-TPD、SEM及BET对催化剂的组成、晶型及酸性进行了表征，发现随着沉淀剂中Na₂CO₃的含量增加，催化剂中CaO∶MgO的比例增大，碳酸丙烯酯的收率亦升高；经850℃焙烧后，催化剂中存在CaO和MgO两种活性中心，起协同催化作用；随着焙烧温度由700℃升高到850℃，NH₃-TPD脱附曲线向低温方向偏移，且强酸中心NH₃脱附峰面积比由81.14%明显下降为0，中强酸中心NH₃脱附峰面积比由0增加到78.07%，而碳酸丙烯酯收率由68%增加到84.6%，这表明催化剂强酸性位的减少是催化活性增加的主要原因。     

Preparation and Properties of a New Mediumdensity and High-strength Ceramic Proppant

Based on the needs of the market,a new 52 MPa medium-density and high-strength ceramic proppant was prepared by adopting third grade bauxite and clay as raw materials and using the solid phase sintering method,and the effect of the firing temperature on the microstructure,phase composition and mechanical properties of the ceramic proppant was studied. The broken resistance mechanism of this ceramic proppant was also discussed. The results show that the main phases of the prepared ceramic proppant are mullite and corundum; the broken rates are 3. 92% and 7. 21% under 52 MPa and69 MPa,respectively.     

Bearing Failure Optimization of Composite Double-Lap Bolted Joints Based on a Three-Step Strategy Marked By Feasible Region Reduction and Model Decoupling

To minimize the mass and increase the bearing failure load of composite doublelap bolted joints, a three-step optimization strategy including feasible region reduction, optimization model decoupling and optimization was presented. In feasible region reduction, the dimensions of the feasible design region were reduced by selecting dominant design variables from numerous multilevel parameters by sensitivity analyses, and the feasible regions of variables were reduced by influence mechanism analyses. In model decoupling, the optimization model with a large number of variables was divided into various sub-models with fewer variables by variance analysis. In the third step, the optimization sub-models were solved one by one using a genetic algorithm, and the modified characteristic curve method was adopted as the failure prediction method. Based on the proposed optimization method, optimization of a double-lap single-bolt joint was performed using the ANSYS^® code. The results show that the bearing failure load increased by 13.5% and that the mass decreased by 8.7% compared with those of the initial design of the joint, which validated the effectiveness of the three-step optimization strategy.     

重整生成油选择性加氢脱烯烃 Pd基催化剂的研究

 研究了负载在Al₂O₃载体上的贵金属钯(Pd)基催化剂在重整生成油选择性加氢脱烯烃反应中的性能。在高压微反装置上，采用环己烯、甲苯和正庚烷的混合物为模拟油来评价筛选催化剂，并对不同工业原料油进行加氢试验。结果表明，在现有工业上常用的工艺条件下，采用Pd/Al₂O₃催化剂进行重整生成油全馏分的选择性加氢，不能满足产品质量要求。其原因是高沸点馏分强吸附在催化剂表面，从而导致催化剂失活。在适宜的工艺条件下，采用Pd/Al₂O₃催化剂进行连续重整汽油BTX 馏分选择性加氢脱烯烃，可以使加氢汽油满足芳烃抽提进料的质量要求。添加助剂对Pd/Al₂O₃催化剂进行改进，可以大大提高催化剂的稳定性。改进后的双金属Pd基催化剂(Pd+M/Al₂O₃)可用于不同原料的重整生成油（苯(C6)馏分、BTX(C6~C9)馏分、全馏分）的选择性加氢脱烯烃反应。加氢反应产物的溴价小于200mgBr/100g，芳烃损失小于0.5%(质量分数)，且在重整生成油全馏分的选择性加氢过程中该催化剂表现出好的稳定性。     

低勘探程度区域油气资源评价方法

目前中国油气资源勘探和开发面临后备可采储量不足，低勘探程度区域受到重视。为了提高低勘探程度区域的资源评价精度，在前人评价的基础上，通过研究并利用勘探程度较高区域的资源评价结果，求准低勘探程度区域的油气聚集量，进而模拟求出其烃排聚系数、储量密度系数、单储系数和单生系数等关键参数，提出了利用练台地质推断法对低勘探程度区域进行评价，并对该方法评价的风险进行了分析。综合地质推断法的成果更能准确反映一个盆地、坳（凹）陷或区带的油气潜力及其分布特征。     

电磁超声流量计的研制

基于电磁声换能器的原理，研制了一种新型的电磁超声流量计，并讨论提高测量精度的措施。     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

复相材料的循环变形行为

对三种组织状态的F-M复相钢进行了对称和非对称循环加载条件下的形变研究.结果表明,双相钢的循环变形行为,不仅与组织中位错组态的演变过程有关,同时也受循环载荷大小、类型以及加载方式所影响.分析表明,双相钢的循环硬化、软化行为主要受控于两个基本过程,即循环变形时位错组态演变的物理过程和相间分载应力的转嫁、相间残余应力变化的力学过程.