Study of a BGO calorimeter using electron and hadron beams from 1 to 50 GeV

A calorimeter of 25 bismuth germanate (BGO) crystals equipped with silicon photodiode readout has been tested at the CERN SPS in the energy range 1–50 GeV. The response for electrons has been shown to be linear in this energy range and the rms resolution obtained ( ) is approximately 1%, for E > 4 GeV. The electron/pion separation was found to be better than 1:500 in the energy range 1–20 GeV. Data on lateral and longitudinal shower development were compared with the results of a Monte Carlo simulation using the SLAC-EGS program and found to be in good agreement.     

Generation and selection of likely interpretations during plan recognition in task-oriented consultation systems

This paper presents a mechanism which infers a user's plans from his/her utterances by directing the inference process towards the more likely interpretations of a speaker's statements among many possible interpretations. Our mechanism uses Bayesian theory of probability to assess the likelihood of an interpretation, and it complements this assessment by taking into consideration two aspects of an interpretation: its coherence and its information content. The coherence of an interpretation is determined by the relationships between the different statements in the discourse. The information content of an interpretation is a measure of how well defined the interpretation is in terms of the actions to be performed on the basis of this interpretation. This measure is used to guide the inference process towards interpretations with higher information content. The information content of an interpretation depends on the specificity and the certainty of the inferences in it, where the certainty of an inference depends on the knowledge on which the inference is based. Our mechanism has been developed for use in task-oriented consultation systems. The particular domain that we have chosen for exploration is that of travel booking.     

Detection of failure sites by focused ion beam and nano-probing in the interconnect of three-dimensional stacked circuit structures

Focused ion beam (FIB) and nano-probing were applied for failure analysis of three-dimensional stacked circuits with copper through-silicon-vias between the stacked chips. The failure analysis was done after high temperature storage and thermal cycling tests. Passive voltage contrast in FIB allowed to pinpoint the open sites. FIB cross-sections showed the presence of opens at the bottom of the copper vias. The failure cause was suspected to be an interlayer particle, which was confirmed by optical profilometry. Nano-probing was used on another sample to pinpoint the failure location through the measurement of the local resistance within the daisy chains. The failure was traced out to be related with surface contamination.     

Natural convection from narrow horizontal plates at moderate Rayleigh numbers

The present work deals with the natural convection flow and heat transfer from a horizontal plate cooled from above. Experiments are carried out for rectangular plates having aspect ratios between φ=0.036 and 0.43 and Rayleigh numbers in the range 290?Ra_w?3.3×10⁵. These values of Ra_w and φ have been selected below those commonly considered in previous research in view of a future application to the design of printed circuit boards. The plates are made of two different metals, copper and steel. The choice of a metal is relevant to the present problem because the plates are heated by means of an electric current. Important variations of the surface temperature are observed along the transverse direction for the steel plates. The surface of the copper plates is almost isothermal because of the high thermal conductivity of the metal.Calculations for a semi-infinite plate are carried out to predict the transverse profiles of the surface temperature and heat flux and to visualize the structure of the flow. Three-dimensional calculations are also used at a qualitative level to observe the changes in the flow structure due to the finite length of the plate. Present results are compared with both previous experimental work and analyses that are based on boundary layer theory. It is shown that analyses for an infinite boundary layer are not completely applicable to the present problem because of its different physics. The most relevant feature of the natural convection flow, which is not predicted by boundary layer analyses, is a thermal plume rising near the center of the plate.Present heat transfer results differ from previous experimental work because of the lower Rayleigh numbers and aspect ratios investigated here. The Nusselt number is found to depend on Ra_wⁿ, with the exponent n=0.17 being lower than most of the values reported in the literature. This comparatively low value is related to the transverse conduction of heat through the air, which becomes increasingly significant as Ra_w approaches zero. It is shown that such a low-Ra_w effect can be accounted for in a physically consistent manner by adding a constant term to the heat transfer correlation. On the other hand, it is found that the Nusselt number does not significantly depend on the aspect ratio in the range of φ investigated contrary to what has been previously reported for wider plates.     

The effect of Cu-rich sub-layer on the increased corrosion resistance of Cu-xZn alloys in chloride containing borate buffer

The electrochemical behaviour of Cu-xZn alloys, as well as their constituent metals, in a borate buffer containing chloride ions in the molar range from 0.01 to 1 M are studied. Characteristics of these materials under anodic polarization are compared and the composition and morphology of the corrosion products formed in the course of polarization experiment are analysed by SEM and EDS. X-ray photoelectron spectroscopy and electrochemical impedance measurements are used for characterization of the surface layers formed on Cu, Zn and Cu-40Zn alloy during 2-h immersion at E_oc in a borate buffer containing two different concentrations of chloride ions. New aspects of the behaviour of brass under E_oc condition are revealed. The improved corrosion resistance of brass in chloride media, if compared to zinc metal, is attributed to a Cu-rich layer formed by the selective dissolution of zinc. Based on the results, a structural model describing the improved corrosion resistance of Cu-40Zn alloy with respect to Zn metal is proposed.     

Evolution of weakly non-linear shallow water waves generated by a moving boundary

Summary In this study we describe the evolution of weakly non-linear shallow water waves in a rectangular channel of 16 m length which aregenerated by a moving boundary. We present a detailed comparison of computaticnal and observational waveheight-time series and thus verify the theoretical model as presented by Villeneuve and Savage [27].Three different types of wave generating devices were used: pistons with vertical and inclined frontal faces, submerged boxes and a rotating plate. Waveheight-time series are recorded at eight different positions along the channel by electrical resistivity gauges, and velocity profiles are determined at certain selective cross sections. Data of many wave experiments are presented in nondimensional form. This representation reveals that the initial wave forms depend upon a Froude number of the motion of the wave generator, the slope angle of the wedge-type pistons and on the dimensionless displaced volume. Evolving waveheight-time series that are recorded at the various gauges are compared with those obtained from computations by use of equations which generalize the Boussinesq equations to include time variations of the boundaries.The method of inverse scattering is applied both, experimental and numerical waveheight-time series are prescribed as initial data. Results are tested relative to two different observers one fixed in time the other fixed in space. Deviations are shown to be small in all cases.     

A monotone multigrid solver for two body contact problems in biomechanics

The purpose of the paper is to apply monotone multigrid methods to static and dynamic biomechanical contact problems. In space, a finite element method involving a mortar discretization of the contact conditions is used. In time, a new contact-stabilized Newmark scheme is presented. Numerical experiments for a two body Hertzian contact problem and a biomechanical application are reported. This work was supported by the DFG Research Center Matheon.