全文获取类型
收费全文 | 72篇 |
免费 | 3篇 |
国内免费 | 9篇 |
专业分类
电工技术 | 10篇 |
综合类 | 5篇 |
化学工业 | 6篇 |
金属工艺 | 7篇 |
机械仪表 | 10篇 |
建筑科学 | 1篇 |
矿业工程 | 2篇 |
轻工业 | 4篇 |
水利工程 | 2篇 |
石油天然气 | 7篇 |
武器工业 | 4篇 |
无线电 | 8篇 |
一般工业技术 | 2篇 |
冶金工业 | 3篇 |
自动化技术 | 13篇 |
出版年
2022年 | 2篇 |
2021年 | 2篇 |
2019年 | 1篇 |
2018年 | 1篇 |
2016年 | 2篇 |
2015年 | 1篇 |
2014年 | 10篇 |
2013年 | 2篇 |
2012年 | 5篇 |
2011年 | 3篇 |
2010年 | 2篇 |
2009年 | 1篇 |
2008年 | 5篇 |
2007年 | 4篇 |
2006年 | 6篇 |
2005年 | 6篇 |
2004年 | 3篇 |
2003年 | 2篇 |
2002年 | 3篇 |
2001年 | 4篇 |
2000年 | 4篇 |
1999年 | 3篇 |
1998年 | 1篇 |
1997年 | 1篇 |
1996年 | 3篇 |
1995年 | 1篇 |
1994年 | 2篇 |
1993年 | 2篇 |
1992年 | 1篇 |
1991年 | 1篇 |
排序方式: 共有84条查询结果,搜索用时 15 毫秒
1.
2.
3.
4.
论述了6MG200-WC大倾角采煤机液压系统工作原理,实践证明该液压系统工作性能良好,安全可靠。 相似文献
5.
用于Marx发生器电压测量的水电阻分压器 总被引:3,自引:2,他引:1
为了测量PTS单路样机Marx发生器的输出电压,设计并标定了一个二级分压的水电阻分压器。水电阻分压器设计中需注意在不同介质的分界面及三相点位置产生的局部高电场,采取适当的均压设计可避免绝缘击穿。水电阻分压器用比对法标定,短路实验和100Ω水电阻负载实验的标定结果相差约15%。分析认为误差的原因是标准分压器和Marx发生器输出端的连接线与主回路之间存在互感,造成短路负载情况下标准分压器的测量值低于实际值,导致标定结果出现较大偏差。改进实验线路后标定结果偏差<3%。 相似文献
6.
发动机齿环常规生产工艺包括下料→冲孔→扩孔成形→正火→酸洗→校正等过程。使用箱式炉正火,工件氧化严重,变形大,能耗大。采用手工校正薄壁环形件的椭圆度和平面度,劳动强度大,质量难以保证,更不能满足我厂索菲姆发动机批量生产的要求。由于可控硅中频感应加热的... 相似文献
7.
8.
9.
Ti2AlC bulk material was synthesized by hot pressing of mixture powders of TiC, Ti, Al and active carbon. The phase compositions of resultant product at different temperature were detected by X-ray diffractometer. The microstructures of the samples were observed by SEM. Finally, the mechanical properties and thermal properties of the sample at 1 400 ℃ were measured. The results show that high purity Ti2AlC material with little Ti3AlC2 can be synthesized by hot pressing 0.5TIC/1.5Ti/1.0A1/0.5C at 1 400 ℃. Ti2AlC exhibits high mechanical properties and metallic electrical properties. Its fractm'e toughness is 7.0 MPa·m^1/2, its flexural strength is 384 MPa at room temperature, and its electrical conductivity is 2.56 × 10^6 Ω^-1·m^-1 at room temperature. 相似文献
10.