Effect of CNTs on Activation Volume and Mobile Dislocation Exhaustion Rate of CNTs/Al under Compression Loading

In this study, stress relaxation compression tests were performed to investigate the strain rate sensitivity, activation volume and mobile dislocations in carbon nanotubes/aluminum (CNTs/Al) composites. The results reveal that, with the addition of CNTs, the strain rate sensitivity of CNTs/Al increased. Meanwhile, a smaller V^* of CNTs/Al compared with pure Al was attributed mainly to the CNT-Al interfaces and partly to the increased forest dislocations cutting activities in grain interior, which was related to the tendency of short ranges order formation during plastic deformation. The incorporation of CNTs also improved the dislocation storage capability and reduced the dislocation velocity, leading to a lower mobile dislocation exhaustion rate.     

Effects of fermentation conditions and soybean peptide supplementation on hyaluronic acid production by Streptococcus thermophilus strain YIT 2084 in milk

To increase the hyaluronic acid (HA) yield from Streptococcus thermophilus YIT 2084, fermentation conditions (pH, temperature, agitation, aeration) were optimized in milk-based medium, and the effects of supplemental soybean peptides, which have different molecular weight distributions, were determined. HA production was enhanced to approximately 100 mg/l at pH 6.8 and 33–40 °C. Agitation speed and aeration rate slightly affected HA production. Soybean peptides including those of high molecular weight (approximately 27 to 130 kDa) further increased HA production to 208 mg/l under the optimal condition (pH 6.8, 35 °C, 100 rpm), which was 20-fold greater than non-optimal condition. HA production was no longer related to the specific growth rate. The HA produced under the optimal condition included a large amount of high-molecular-weight fraction of 100 to 2000 kDa, compared with under the basal condition without optimization.     

Molecular structures of gellan gum imaged with atomic force microscopy (AFM) in relation to the rheological behavior in aqueous systems in the presence of sodium chloride

Aqueous solutions of gellan gum with comparable molecular mass but with different acyl contents were investigated by atomic force microscopy and rheological measurements in the presence of sodium chloride (NaCl). Results obtained were discussed in relation to our previous report using potassium chloride (KCl) as an added salt. For a low-acyl sample, continuous fibrous network structures were identified microscopically as in the case of KCl. The network structures were more heterogeneous than those formed with KCl in terms of the height distribution of molecular assemblies. Rheological thermal hysteresis between sol–gel transitions was detected as in the case of KCl. The storage modulus (G′) of the gelled system was ca. 15% of the corresponding data with KCl at 20 °C. For a high-acyl sample, no continuous network structures were identified but branches with observable ends were identified as in the case of KCl. The hysteresis was less evident than the corresponding data with KCl and for the low-acyl sample with NaCl. Also, G′ values at 20 °C were ca. 30% and 20% of the corresponding data with KCl and for the low-acyl sample with NaCl, respectively. Continuousness and homogeneity of network structures related to the hysteresis and elasticity of the system, respectively.     

Observation of metal on Si(0 0 1) by STM/STS and its consideration based on the first principles calculations

Local density of states (LDOS) is obtained by the first principles calculation based on the density functional theory on the Si(0 0 1)2 × 1 surface and on the surface with an Al dimer. At an Al dimer, LDOS has a high intensity in the conduction band region, which cannot be seen on the Si(0 0 1)2 × 1 surface. This tendency is observed in STS measurements as well. The possibility for a microelementary analysis is presented by applying this method to other metal atoms on the Si surface. Furthermore, it is pointed out that STS measurements should be always performed at the same tip-sample separation to obtain reproducible STS spectrums.     

Aging behavior of the matrix of aluminum-magnesium-silicon alloy including carbon nanotubes

The mechanical behavior of the non-aged and the aged Al-Mg-Si alloy composites reinforced with CNTs was evaluated with tensile test and Vickers hardness test. The composites showed higher mechanical strength than the pristine Al alloy before the aging, although exhibiting lower mechanical strength after the aging. The aging treatment was ineffective to strengthen the Al-Mg-Si alloy composites reinforced with CNTs. EDS elemental mapping clarified the Mg and O concentration around CNTs. The reduction of Al oxide species formed around CNTs facilitated the Mg concentration. Due to the Mg consumption around CNTs, Mg elements in Al matrix decreased, and resulted in the incomplete matrix strengthening after the aging.     

The texture and anisotropy of hot extruded magnesium alloys fabricated via rapid solidification powder metallurgy

Rapid solidification magnesium alloy powders produced by spinning water atomization process were hot extruded into rectangular bars, from which tensile and compression samples have been cut at 0°, 45° and 90° angles from the extrusion direction to study their anisotropy. Electron back-scattered diffraction analysis has been used to investigate the texture evolution during the extrusion process. Texture parameters like the Schmid factor and the intensity of (0 0 0 1) basal plane in the pole figure have been evaluated and correlated to the mechanical properties. Results have shown that the extruded rods exhibited high strength and relatively less anisotropy compared to other previously reported values for wrought magnesium alloys. Tensile and compression yield stresses have shown very similar values to each other at all loading directions. This limited anisotropy could be linked to both the fine grained and inter-metallic-compound-dispersed microstructure of the extruded alloys. Dynamic recrystallization behavior during hot extrusion has also been investigated in the present study.     

Fabrication of magnesium based composites reinforced with carbon nanotubes having superior mechanical properties

Magnesium (Mg) composite reinforced with carbon nanotubes (CNTs) having superior mechanical properties was fabricated using both pure Mg and AZ61 Mg alloy matrix in this study. The composites were produced via powder metallurgy route containing wet process using isopropyl alcohol (IPA) based zwitterionic surfactant solution with unbundled CNTs. The produced composites were evaluated with tensile test and Vickers hardness test and analyzed by X-ray diffraction (XRD) and field-emission scanning electron microscopy (FE-SEM) equipped with energy dispersive spectroscopy (EDS) and electron back scattered diffraction (EBSD). As a result, only with AZ61 Mg alloy matrix, tensile strength of the composite was improved. In situ formed Al₂MgC₂ compounds at the interface between Mg matrix and CNTs effectively reinforced the interfacial bonding and enabled tensile loading transfer from the Mg matrix to nanotubes. Furthermore, it was clarified that the microstructures and grain orientations of the composite matrix were not significantly influenced by CNT addition.     

Possible mechanism for the anti-atherosclerotic action of the calcium channel blocker AE0047 in cholesterol-fed rabbits

The genetics of resistance to disease is an area of great interest in agriculturally important plant and animal species. Selective breeding for resistance to pathogens in plants, animals and insects has demonstrated that resistance and susceptibility to pathogens are controlled by both genetic and environmental factors. The immune loci causally involved in susceptibility and resistance to disease are currently unknown. However, novel enabling molecular technologies promise to assist in unravelling the genetics of the host response to infectious diseases in new ways, and ultimately to improve seed stock genetics.