Microstructure evolution during thermomechanical processing in 3Mn-0.1C medium-Mn steel

ABSTRACT

Medium-Mn steels are energetically investigated as a candidate of the third generation advanced high strength steels (AHSSs). However, their phase transformation and microstructaure evolution during various heat treatments and thermomechanical processing are still unclear. The present study first confirmed the kinetics of static phase transformation behaviour in a 3Mn-0.1C medium-Mn steel. Hot compression tests were also carried out to investigate the influence of high-temperature deformation of austenite on subsequent microstructure evolution. It was found that static ferrite transformation was quite slow in this steel, but ferrite transformation was greatly accelerated by the hot deformation in austenite and ferrite two-phase regions. Characteristic dual-phase microstructures composed of martensite and fine-grained ferrite were obtained, which exhibited superior mechanical properties.

This paper is part of a Thematic Issue on Medium Manganese Steels.     

Friction Powder Compaction for Fabrication of Open-Cell Aluminum Foam by the Sintering and Dissolution Process Route

A new friction powder compaction (FPC) process by the sintering and dissolution process (SDP) route for fabricating open-cell aluminum (Al) foam, which requires no external heat sources, was developed. Foams with porosities of 74 and 83 pct were successfully fabricated and their compressive responses were investigated. The sintered mixture during the removal process was observed nondestructively by X-ray computed tomography (CT) to reveal the progress of the removal of soluble particles and to confirm that they were completely dissolved.     

In vitro formation and thermal transition of novel hybrid fibrils from type I fish scale collagen and type I porcine collagen

Novel type I collagen hybrid fibrils were fabricated by neutralizing a mixture of type I fish scale collagen solution and type I porcine collagen solution with a phosphate buffer saline at 28 °C. Their structure was discussed in terms of the volume ratio of fish/porcine collagen solution. Scanning electron and atomic force micrographs showed that the diameter of collagen fibrils derived from the collagen mixture was larger than those derived from each collagen, and all resultant fibrils exhibited a typical D-periodic unit of ∼67 nm, irrespective of volume ratio of both collagens. Differential scanning calorimetry revealed only one endothermic peak for the fibrils derived from collagen mixture or from each collagen solution, indicating that the resultant collagen fibrils were hybrids of type I fish scale collagen and type I porcine collagen.     

Synthesis of non-equilibrium phases in immiscible metals mechanically mixed by high pressure torsion

The structural changes in mechanically mixed metals of immiscible combinations of elements caused by bulk mechanical alloying (MA) through the use of high pressure torsion (HPT) were investigated in Ag–Ni and Nb–Zr systems. There was no alloying between Ag and Ni on atomic scale even after 100 rotations of HPT. On the other hand, the β-Zr phase started to appear after HPT 2 rotations in the Nb–Zr system, even though β-Zr is a high temperature phase. Further, Nb and Zr were completely mixed to form a bcc structured single phase after HPT 100 rotations. The sequence of alloying in the Nb–Zr system during HPT was discussed. These results clearly suggest that non-equilibrium phases can form in the Nb–Zr system by bulk MA by the use of HPT.     

添加合金元素对奥氏体不锈钢等离子渗氮和渗碳的影响

奥氏体不锈钢众所周知有良好的耐蚀性,但是在工业上没有用于承受摩擦的工件上,因为它的硬度低,摩擦磨损性能差。奥氏体不锈钢经低温等离子体渗氮或渗碳能生成一层特殊的氮化物或碳化物层,称为S相,它具有高的硬度和优良的耐蚀性。这项研究中各种奥氏体不锈钢都经低温等离子体渗氮或渗碳,用各种分析技术研究了添加合金元素对S相特性的影响,用了光学显微镜和电子显微镜观察,做了X射线衍射分析,在5%H2SO4溶液中测量阳极极化,用球对平面摩擦装置做摩擦磨损测试。氮化物或碳化物层厚度随处理温度增加而加厚,AISI316钢上生成的渗层厚度是所有的基体钢材中最厚的。超过临界温度,由于氮化铬工碳化铬沉淀使耐蚀性降低。临界温度由渗氮的基材决定。另一方面,在渗碳层中临界温度不随基材变化。大部分样品上S相层的耐蚀性比没有处理的不锈钢的低。但是,AISI316和JIS-SUS304J3钢在400℃渗碳后都有和未处理钢一样优良的耐蚀性。每种不锈钢经渗氮或渗碳后耐磨性都有明显的改进。     

Yielding behavior and its effect on uniform elongation in IF steel with various grain sizes

In the present study, IF steel specimens with different grain sizes ranging from 12 to 0.45 μm were fabricated by accumulative roll-bonding process and subsequent annealing. Tensile tests revealed that by decreasing the mean grain size down to an ultrafine range smaller than approximately 1.5 μm, yielding behavior of the IF steel gradually changed from continuous yielding to discontinuous yielding. An abrupt loss in the uniform elongation occurred, when the average grain size was smaller than about 1 μm. Hall–Petch analysis on the yield stress and uniform elongation implied that the abrupt loss in the uniform elongation in the UFG grain size range corresponded to the appearance of the discontinuous yielding behavior. As it has been found in many UFG materials, discontinuous yielding is believed to be a unique mechanical behavior of UFG materials, and it has significant importance on the uniform elongation of UFG materials.     

Template-free hydrothermal synthesis of hollow hematite microspheres

Hollow hematite (α-Fe₂O₃) microspheres with an average diameter of 3-4 μm and a shell thickness of approximate 150 nm was synthesized by a simple hydrothermal route using FeCl₃·6H₂O solution and acetic acid without using any templates. The hollow microspheres were composed of α-Fe₂O₃ nanoparticles with the diameter range from 20 to 40 nm. The effects of reaction parameters such as reaction time, temperature, concentration of FeCl₃·6H₂O solution, and initial pH on the morphology of the final products were investigated. A possible formation mechanism of hollow α-Fe₂O₃ microspheres was also proposed, where the acetic acid played a role of etching in the formation of hollow structure.