Error estimation for the automated multi‐level substructuring method

In this study, we propose an effective method to estimate the reliability of finite element models reduced by the automated multi‐level substructuring (AMLS) method. The proposed error estimation method can accurately predict relative eigenvalue errors in reduced finite element models. A new, enhanced transformation matrix for the AMLS method is derived from the original transformation matrix by properly considering the contribution of residual substructural modes. The enhanced transformation matrix is an important prerequisite to develop the error estimation method. Adopting the basic concept of the error estimation method recently developed for the Craig–Bampton method, an error estimation method is developed for the AMLS method. Through various numerical examples, we demonstrate the accuracy of the proposed error estimation method and explore its computational efficiency. Copyright © 2015 John Wiley & Sons, Ltd.     

Nanotextured superhydrophobic micromesh

A superhydrophobic micromesh covered with nanoprotrusions has been introduced and its applicability to a waterproof mobile phone speaker has been evaluated. The nanotextured superhydrophobic micromesh showed excellent water repellency, self-cleaning and waterproofing performances. In a waterproof speaker test using the fabricated nanotextured micromesh, the micromesh did not lose its waterproof function at 2 m water depth and did not form a remnant water film after being removed from the water. The packaged speaker showed almost the same sound quality before and after dipping at a 2 m water depth. These results demonstrate that the superhydrophobic nanotextured micromesh could be directly applicable for various products that need to resist water penetration, yet allow the transmission of gases and sound/light waves.     

Mechanical properties of unidirectionally transformed Cu-In alloys

Comprehensive hardness measurements and limited tensile tests have been made on eutectoid and off-eutectoid Cu-In alloys. The alloys were transformed by unidirectional heat-treatment techniques using a range of imposed growth rates which resulted in alignment of the pearlite microstructure and a range of interlamellar spacing. Room temperature hardness of the as-transformed alloys was found to vary linearly as a function of ^–1/2, where is the pearlite interlamellar spacing; the alloys were calculated to have cooled from the decomposition temperature at rates in the range 0.047 to 18.6 K min^–1, which could result in variations of precipitation/coarsening reactions in the pearlitic phases contributing towards strength, as well as the lamellae interfaces. Hardness was also measured as a function of temperature and indicated a change in strengthening mechanism at 550 K, thought to indicate the temperature above which no significant strengthening was contributed by the pearlitic interfaces. Tensile failure of the lamellar structure occurred in a manner identical to directionally aligned Al-CuAl₂ eutectics.     

Potentiation and inhibition of nicotinic acetylcholine receptors by spermine in the TE671 human muscle cell line

Nicotinic acetylcholine receptors (nAChR) of the TE671 cell line were investigated using whole-cell and membrane patch recording techniques. At negative holding potentials (VH), pulses of acetylcholine (ACh) elicited whole-cell inward currents that rapidly desensitized. The EC50 value for ACh at VH = -60 mV was 7.8 microM. The ACh-induced current reversed at approximately 0 mV. Desensitization of nAChR by ACh was biphasic and reversible within approximately 20 sec. Spermine (1-100 microM) potentiated responses to ACh (10 microM - 1 mM) by reducing the rate of onset of desensitization; potentiation was inhibited by arcaine (10-100 microM). Spermine (1 mM) noncompetitively antagonized the AChinduced current. Antagonism by 1 to 5 mM spermine was voltage-dependent, increasing with negative VH. In 100 microM arcaine, this antagonism was shown to contain a voltage-independent component. Spermine (10 mM) increased the EC50 values for ACh, suggesting that at this concentration the polyamine is also a competitive antagonist. Single channel openings elicited during application of ACh to outside-out patches had a conductance of 47 pS at VH = -60 mV. At 10 and 100 microM, spermine increased channel open probability (po), but at 1 mM spermine, po was not significantly different from controls. The single channel conductance for ACh was unaffected by 10 and 100 microM spermine, but was decreased by 1 mM spermine. Spermine promoted the occurrence of approximately 27 pS openings. It is proposed that spermine acts at an excitatory modulatory site similar to that present on N-methyl-D-aspartate receptors and at least three inhibitory sites on nAChR of TE671 cells.     

Key factors determining the energy rating of existing English houses

In the UK, the Standard Assessment Procedure (SAP) is used to rate the energy performance of existing dwellings whenever they are let or sold. This study investigates which of the inputs to SAP account for the most variance in energy rating across existing gas central heated houses in England. Data from the English Housing Survey (EHS) 2009 are used to generate a representative set of dwellings and variance-based global sensitivity analysis is then applied to assess each input's contribution to the variance in the calculated ratings. It is demonstrated that heating system efficiency, external wall U-value and dwelling geometry account for 75% of the variance of the energy rating of gas central heated houses in England. This suggests that improving heating system efficiencies and wall U-values of the worst performing dwellings will go a long way towards improving their energy rating and potentially reducing their energy consumption. It is also demonstrated that dwelling geometry has a much bigger influence on the calculated carbon emissions (accounting for 80% of the variance) than it does on the SAP energy rating (accounting for 30%), meaning that significant improvements in energy rating might not be accompanied by significant reductions in carbon emissions.     

在铅焊料的标准流程中用无铅元件

随着欧洲的RoHS和WEEE指令已于2006年7月1日开始执行,许多元件供应商面临着使其产品符合无铅环境的挑战。两个指令都要解决将铅从元件中去除的问题。半导体公司必须选择高性价比、与含铅焊料逆向兼容,并与无铅焊料前向兼容的无铅镀层策略。逆向兼容表示无铅元件能够用锡铅（SnPb）焊料回流工艺安放在PCB上。前向兼容表示目前的锡铅工艺能够在面板组装中,与无铅焊料一起使用。