An experimental study of a cross-flow type plate heat exchanger for dehumidification/cooling

The thermal and dehumidification behaviour of a standard cross-flow type plate heat exchanger, intended for use as a dehumidifier/cooler, has been investigated both experimentally and numerically. Three sets of experiments have been carried out where air is blown into the primary and secondary sides of the exchanger, while water and liquid desiccant were being sprayed in a counter flow arrangement. The first set represents the indirect evaporative cooling of the primary stream by the secondary air stream. The second set is with liquid desiccant only and no indirect evaporative cooling. In the third set of experiments the primary air stream is indirectly evaporatively cooled by the secondary air stream and dehumidified by the liquid desiccant sprayed into the primary side of the exchanger. The above experiments indicate that the heat exchanger performs well when used with liquid desiccant. Furthermore, for an exchanger angle of 45°, there is an optimum value of air mass flow rate at which the effectiveness and dehumidification efficiency of the plate heat exchanger are maxima. To investigate the effect of the ambient air conditions on the PHE performance, further experiments were carried out using a heater element and a humidifier. The results show that under laboratory conditions the exchanger effectiveness and dehumidification efficiency increase with increasing primary air inlet temperature and humidity ratio. The experimental results were used to validate a computer model developed for the cross-flow type plate heat exchanger/dehumidifier. Comparison indicates that the numerical results are in good agreement with the experiments.     

Mechanical characterization and modeling stress relaxation behavior of acrylic–polyurethane-based graft-interpenetrating polymer networks

The stress relaxation behavior of acrylic–polyurethane (PU)-based graft-interpenetrating polymer networks (IPNs) was characterized via dynamic mechanical analysis (DMA) and modeled using finite element method (FEM) analysis. Stress relaxation of glassy IPN specimens was experimentally studied under flexural testing, while rubbery IPN specimens were tested in tension. The effects of varying the styrene content in the acrylic copolymer phase, compatibility of the two phases in IPNs, and changing the concentration of acrylic copolymer and PU were studied. A higher percentage of styrene content resulted in higher homogeneity of IPN specimens, and decrease in initial modulus for acrylic copolymer specimens. Additionally, glassy IPN specimens with 90% styrene shows resistance to relaxation as high as acrylic copolymer samples. Experimental results were used to develop a numerical model to study stress relaxation response of specimens. While polymer systems have been studied computationally, numerical modeling of IPN systems is still in its infancy. A three-dimensional FEM model was developed using the Generalized Maxwell model and four-term Prony series constants, which were extracted from the stress relaxation experiments. With four terms in the Prony series, a good match was observed between experimental observations and results from the FEM model.     

Preparation and characterization of poly(vinyl alcohol)/gum tragacanth/cellulose nanocomposite film

The effects of gum tragacanth obtained from two species of Astragalus Gossypinus (GT-G) and A. Parrowianus (GT-P) at two levels of 10% and 30% combined with cellulose nanofibers (CNF; 5%) on the physico-mechanical and structural properties of polyvinyl alcohol (PVA) nanocomposite film were investigated in this study. The water solubility and water vapor permeability of the films decreased with increasing the content of both gums, especially in the film containing 30% GT-P. The highest values of the tensile strength (39.3 MPa) and elongation at break (445%) belonged to the treatment containing 10% GT-P (90/10P/0). The FTIR and DSC analyses confirmed good interactions between GT and PVA in the 90/10P/0 treatment. SEM images indicated the dense structure of this film as the optimum treatment. Although the presence of CNF in the films containing GT-G improved some properties, especially the Young modulus, it impaired all the functional properties of nanocomposite GT-P film.     

An adaptive neuro‐fuzzy system for stock portfolio analysis

We propose an adaptive neuro‐fuzzy inference system (ANFIS) for stock portfolio return prediction. Previous work has shown that portfolio optimization can be improved by using predicted stock earnings rather than historical earnings. We show that predicted portfolio returns can be improved by using ANFIS and taking as input a variety of technical and fundamental attributes about various indices of the stock market. To generate membership functions, we use a robust noise rejection‐clustering algorithm. The neuro‐fuzzy model is tested on portfolios constituted from the Tehran Stock Exchange. In our experiments, the proposed method performs better in predicting the portfolio return than the classical Markowitz portfolio optimization method, a multiple regression, a neural network, and the Sugeno–Yasukawa method. © 2010 Wiley Periodicals, Inc.     

Adaptive Control for State Synchronization of Nonlinear Haptic Telerobotic Systems with Asymmetric Varying Time Delays

In this paper, we introduce a new adaptive controller design scheme for nonlinear telerobotic systems with varying time delays where the delays and their variation rates are unknown. The designed controller has the ability to synchronize the state behaviors of the local and the remote robots. In this paper, asymptotic stability in the presence of varying time delays is of interest. Using the proposed controller, asymptotic stability of the bilateral telerobotic system subject to any bounded yet unknown varying delay with a bounded yet unknown rate of change can be guaranteed. Besides the varying time delay, the proposed adaptive controller has the ability to adapt to the parameter variations in the local and the remote robots’ dynamics. It is shown that position and velocity errors between the local and the remote manipulators converge to the zero asymptotically, thus ensuring teleoperation transparency. Experimental and simulation results with a pair of PHANToM haptic devices and a pair of planar manipulators under varying time delays in the communication channel demonstrate the effectiveness of the proposed scheme.     

Electro-osmosis treatment techniques and their effect on dewatering of soils,sediments, and sludge: A review

Electro-osmosis is an established method of dewatering fine soils, sediments, and sludge (SSS). The efficiency of electro-osmotic treatment is controlled by the electrical resistance of the system. Due to an increase in SSS resistance during treatment, its cost efficiency is reduced, limiting the widespread use of this technique. The aim of this paper is to discuss the main reasons for the increase in SSS resistance during treatment and then to analyze the most recent and widely spread modifications to classical electro-osmotic treatment that attempt to combat these issues and improve the efficiency of the technique. These modifications to electro-osmotic treatment are polarity reversal, an intermittent current, the injection of chemical solutions at the electrodes, and the use of geo-synthetics. The paper discusses the relevant research on the above adaptations, and the advantages and disadvantages of each are evaluated and compared using the available laboratory and field tests in the literature on electro-osmotic dewatering research. All four methods of modification are shown to provide significant improvements and can be successfully translated to the field for greater use. However, the improvements they bring about may not be sufficient to warrant their general use in geotechnical applications.     

Phase behaviour modelling of Athabasca bitumen for in situ combustion applications

Phase behaviour modelling of reservoir fluid is a fundamental step for reservoir simulation. Furthermore, as the complexity of the recovery process increases, the fluid model plays a more important role in the reliability of the simulation outputs. Although the in situ combustion enhanced oil recovery method (ISC) is one of the most complex recovery techniques available in the petroleum engineering literature, for most of the simulation jobs related to this elaborate process only simple and rudimentary fluid characterization layouts are considered. In this work, the principal fluid properties of Athabasca bitumen with regard to the ISC process are recognized, extracted from the literature, validated for consistency, and used for the development of an inclusive and accurate fluid model. Then the fluid model is fully developed while considering the ISC reaction kinetics so that the model has both accuracy, indispensable for phase behaviour modelling, and consistency, essential for the reactions definitions.