天然橡胶乳液压敏胶粘剂

本文介绍了天然橡胶胶乳压敏胶的基本情况，内容包括基本组成、主要优缺点和改进方法。     

Influence of Ammonium Pentaborate (APB) on the Performance of Urea Formaldehyde (UF) Adhesives for Plywood

Ammonium pentaborate (APB) was used to modify urea formaldehyde (UF) resins, in which the formaldehyde to urea molar ratio was set at 1.80, 1.50, 1.25, and 1.05. Some specific properties, including gel time, free formaldehyde content in UF, bond strength, and formaldehyde emission levels from plywood were evaluated. The result showed that APB increased the gel time length, but also decreased free formaldehyde content and emission levels, which was reduced mostly by 79.0% and 81.4%, respectively. The result of bond strength indicated that APB was proper to modify high F/U molar ratio of UF resin regardless of the loading level, but a recommended loading level should be considered to relevantly lower the F/U molar ratio of UF. The suggested loading level of APB to UF is 8.0% to 6.0%, 6.0%, and 4.0% to UF resin with F/U molar ratio of 1.8, 1.5, and 1.25 separately.     

Urea–formaldehyde resin prepared with concentrated formaldehyde

The characteristics of UF resin prepared with concentrated formaldehyde were studied in this paper. With the molar ratio F/U = 1.1, the UF resin prepared with concentrated formaldehyde showed better mechanical properties than that with formalin. The ¹³C-NMR and FTIR results indicated that there were more methylene groups, ether groups and urons in a UF resin system prepared with concentrated formaldehyde than those in a normal UF resin. The differential scanning calorimetry and DMA results showed that the curing temperature of UF resin with concentrated formaldehyde was lower than that of a normal UF resin. UF resin with concentrated formaldehyde showed worse thermal stability and higher thermal decomposition temperature.     

酚醛基炭气凝胶的研究进展

炭气凝胶是一种多孔纳米炭材料,具有低密度、高孔隙率、高比表面积、优异的导电性和良好的成型性能等优点,是炭材料研究的热点和重要方向。本文旨在通过阐明酚醛基炭气凝胶的制备原料和制备工艺的发展过程,从而突出未来酚醛基炭气凝胶的发展方向。基于此,本文首先重点介绍了酚醛基炭气凝胶的制备方法,主要包括溶胶-凝胶化、干燥以及炭化过程三个最主要的步骤;进而详述了以三种不同的前体,即间苯二酚、苯酚、生物质单宁/木质素分别制备酚醛基炭气凝胶的方法及其优缺点;接下来对酚醛基炭气凝胶作为吸附材料（气体吸附/液体吸附）的吸附量以及在电化学储能以及其他领域的应用进行了综述;最后对酚醛基炭气凝胶未来的研究方向和发展前景进行了总结和展望。文章指出,传统的以间苯二酚为原料辅以超临界干燥的方法制备的酚醛基炭气凝胶,原料成本较高,反应条件苛刻,实际生产应用受限;以苯酚取代间苯二酚,亦或是采用冷冻干燥等方法改进其制备工艺,可以大幅度降低原料和生产成本;但未来的发展方向和重点将是绿色、可再生的生物质原料（单宁、木质素、腰果酚等）及复合气凝胶材料的研发。因此,酚醛基炭气凝胶在未来的发展还需要进一步改进其制备工艺和方法,拓宽其原料来源,从而提高性能,扩大应用领域。     

Variation of MUF and PMUF resins mass fractions during preparation

The variation of molecular mass distribution with the progress of the reaction was studied for the following: (i) sequential‐type melamine–urea–formaldehyde (MUF) resin formulations in which the sequence of addition of chemicals follows well‐defined species reactivity principles; (ii) a nonsequential MUF formulation in which simultaneous melamine and urea competition for formaldehyde yields a MF resin cocondensed with small amounts of urea. This resin became soaked with reacted and unreacted monomeric urea species. (iii) A PMUF resin, namely a MUF resin with a small proportion of phenol (7.8% by weight on melamine and urea) cocondensed with the main MUF fraction. All the formulations used were industrial resins formulations in current use. Development and variation of molecular mass fractions, from which performance and other useful resin parameters depend, have been found to depend on the type of resin formulation used for these type of aminoplastic resins. The two very different MUF resin formulations yielded different variations in molecular mass fractions during the progress of the reaction and during the so‐called ambient temperature “maturing” of the resin. The PMUF resin also showed both similar and different fractions present during manufacturing and during short term ageing at ambient temperature. While similarities in recurrent fractions and in trends are common to all the three different formulations, differences between them are also clearly observed. A major proportion of the reaction of some of the aminoplastic resins examined also occurs on ageing (i.e.“maturing” of the resin at ambient temperature), this appearing to be an essential phase of the resin preparation process. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4842–4855, 2006     

Ester acceleration mechanisms in phenol–formaldehyde resin adhesives

An analysis of phenol–formaldehyde (PF) resins obtained by the addition of 0.5–5% glycerol triacetate (triacetin) as an accelerator during resin preparation showed the presence of intermediates involved in the acceleration mechanism. ¹³C-NMR spectroscopy, matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectroscopy (MS), and gel permeation chromatography allowed us to identify some of the intermediates left over in the PF resin itself. The permanence in the resin of these labile intermediates, not easily observed otherwise, appeared to be due to the reaching of the diffusion-controlled phase of the reaction. The mechanism involved appeared considerably more complex and different from any of the mechanisms presented previously. As a consequence of the evident complexity of the mechanism, it was not really possible to advance a complete mechanism of the reaction nor determine the real cause of the increase in the strength of the final network. The mechanism involved the phenate ion of the resin to apparently give a carbonyl or carboxyl group attached to the aromatic ring. Either directly or by subsequent rapid rearrangement after the initial attack, these CO groups were found on sites different from the ortho position. The appearance gathered from NMR shift calculation indicated preferential positioning or repositioning to the para site and, surprisingly, to the meta sites of the phenolic ring. The shifts of these CO groups correspond to those of an anhydride and to no other intermediate structures previously thought of. Anhydride-like bridges were clearly shown by MALDI-TOF MS to contribute to oligomer structures in which linkages between phenol rings were mixed methylene bridges and anhydride bridges. These structures appeared to be temporary, possibly due to the instability of the anhydride bridges; hence, they were in small proportions at any given moment of the reaction. MALDI-TOF analysis clearly indicated that these structures were at some moment an integral part of the structure of the liquid resin and that they existed parallel to the methylene bridges pertaining to a normal PF resin structure. Previous spectra showed that similar but not identical intermediates were present also in organic and inorganic catalyzed PF resins. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100:3075–3093, 2006     

Improving the Performance of Bamboo and Eucalyptus Wood fiber/Polypropylene Composites Using Pectinase Pre-treatments

The potential for using pectinase as a pre-treatment to improve the properties of bamboo or eucalyptus fibers for use in a woody fiber/polypropylene (PP) composite was compared with the addition of a silane coupling agent or NaOH pre-treatment. Pectinase pre-treatment reduced the amount of pectin in both fibers (p < 0.0001) and this reduction was associated with improved tensile strength, modulus of rupture and modulus of elasticity (p < 0.001) of bamboo, or eucalyptus fiber-based composites. Pre-treatment had no consistent effects on the thickness swell or water absorption. The addition of a coupling agent produced similar improvements in panel properties (p < 0.05), but also markedly reduced moisture absorption and thickness swell (p < 0.05). Sodium hydroxide pre-treatment had no consistent effects on panel properties, although it did appear to affect thickness swell. Short pectinase pre-treatment might be useful for enhancing the properties of woody tissue/PP composites while reducing but not completely eliminating the need for coupling agents.     

Influence of nanoclay on urea‐formaldehyde resins for wood adhesives and its model

The addition of small percentages of Na⁺‐montmorillonite (NaMMT) nanoclay appears to improve considerably the performance of thermosetting urea‐formaldehyde (UF) resins used as adhesives for plywood and for wood particleboard. X‐ray diffraction (XRD) studies indicated that NaMMT loses the periodic atomic structure when mixed in small proportions in the acid‐curing environment characteristic of the curing of UF resins. This can be interpreted as becoming exfoliated under such conditions. The partly crystalline structure of the ordered zones of the UF resins is maintained but at a slightly lower level. Differential scanning calorimetry (DSC) indicated that NaMMT has an accelerating effect on the curing of the UF resin. It also appears to lead to a more controlled rate of crosslinking implying a more regular hardened network. The influence of NaMMT addition was particularly noted in plywood by the increase in water resistance of the UF‐bonded panel. In the case of wood particleboard even the dry internal bond strength of the panel, a direct indication of the performance of the resin, improved with small additions of NaMMT. A hypothesis and model of the reasons why such improvement to the performance of UF resins by addition of nanoclay should occur has been presented. This is based on the application of percolation theory to the networking capability of the clay nanoplatelets. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

三聚氰胺-尿素-甲醛共缩聚树脂的性能研究

合成了三聚氰胺-尿素-甲醛(MUF)共缩聚树脂,考察了不同施胶量、固化剂用量及木材种类对胶合木性能的影响。结果表明,MUF共缩聚树脂用量为300g/m2,双面施胶,固化剂用量在1~2%时,生产的胶合木性能最优。     

蒙脱土对脲醛树脂性能的影响

以有机蒙脱土(OMMT)作为脲醛树脂(UF)胶粘剂的改性剂,制备UF/OMMT纳米复合材料;然后将其用于刨花板的制备,并采用红外光谱(FT-IR)法和X-射线衍射(XRD)法对纳米复合材料的结构进行了表征。结果表明:刨花板的力学性能随OMMT含量增加呈先升后降(或先升后降再升)态势,并且在w(OMMT)=3%时相对较好;当w(OMMT)=1%时,经硅烷偶联剂(KH-550)处理后的OMMT在UF反应终了阶段加入时,刨花板的综合力学性能相对最好;在纳米复合材料体系中,OMMT的层状纳米片层已被剥离,并且OMMT和UF之间发生了一定程度的化学反应,而偶联剂和OMMT之间并没有形成化学键。