In vivo Kinetic Biodistribution of Nano‐Sized Outer Membrane Vesicles Derived from Bacteria

Evaluation of kinetic distribution and behaviors of nanoparticles in vivo provides crucial clues into their roles in living organisms. Extracellular vesicles are evolutionary conserved nanoparticles, known to play important biological functions in intercellular, inter‐species, and inter‐kingdom communication. In this study, the first kinetic analysis of the biodistribution of outer membrane vesicles (OMVs)—bacterial extracellular vesicles—with immune‐modulatory functions is performed. OMVs, injected intraperitoneally, spread to the whole mouse body and accumulate in the liver, lung, spleen, and kidney within 3 h of administration. As an early systemic inflammation response, increased levels of TNF‐α and IL‐6 are observed in serum and bronchoalveolar lavage fluid. In addition, the number of leukocytes and platelets in the blood is decreased. OMVs and cytokine concentrations, as well as body temperature are gradually decreased 6 h after OMV injection, in concomitance with the formation of eye exudates, and of an increase in ICAM‐1 levels in the lung. Following OMV elimination, most of the inflammatory signs are reverted, 12 h post‐injection. However, leukocytes in bronchoalveolar lavage fluid are increased as a late reaction. Taken together, these results suggest that OMVs are effective mediators of long distance communication in vivo.     

Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Solid phase crystallization of amorphous silicon on glass by thin film heater for thin film transistor (TFT) application

A new process for solid phase crystallization (SPC) of amorphous silicon (a-Si) using thin film heater is reported. With this localized Ti silicide thin film heater, we successfully crystallized 500 Å-thick a-Si in a few minutes without any thermal deformation of glass substrate. The size of crystallized silicon grain was abnormally big (30-40 μm). Polycrystalline thin film transistors (TFT) fabricated using this unique thin film heater showed better mobility than those of conventional ones by furnace annealing.     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version