Accelerated aging of extruded dielectric power cables. I. Controland monitoring methodology

An improved accelerated cable life test is described. Through the use of programmable logic controllers (PLCs), very precise and consistent control of the accelerated aging process has been achieved. A computer has been utilized to make continuous real-time acquisition and storage of key operating parameters possible. This precise control and monitoring methodology has permitted the study of the synergistic effects of voltage and temperature on the accelerated aging of full-sized cables in the laboratory     

Inertia-friction welding of SiC-reinforced 8009 aluminium

Inertia-drive friction welding (IFRW) of an 8009 Al alloy (Al-8.5 Fe-1.7 Si-1.3 V, wt%) reinforced with 11 volume per cent SiC particles (8009/SiC/11_p) has been investigated. Inertia-drive friction welds were made with constant energy at two levels of axial force. The microstructures of the base material and the welds were characterized using optical and scanning electron microscopy, while the mechanical properties were evaluated using microhardness and tensile testing. Examination of weld sections revealed that the hot deformation experienced during welding produced a homogenized microstructure with a uniform distribution of SiC particles along the bond line. No evidence of a chemical reaction between the SiC and the matrix was found in any of the welds, but cracking of some of the larger SiC particles was observed in the base material as well as in the IFR welds. The average microhardness of the various heat-and-deformation affected zones (HDZs) of the welds did not vary greatly from that of the base material, and no weld induced weak regions were discerned. The room-temperature (RT) tensile strength of the IFR welds exceeded 90 per cent of the base material. The weld tensile specimens failed at the outer edge of the HDZ for all of the welds tested. The fracture surface of the 8009 matrix of tensile samples for both the base material and the welds exhibited a dimpled appearance indicating a ductile failure, while fracture through the SiC appeared to occur in a brittle fashion. IFRW has proven effective in joining 8009/SiC/11_p with little loss in RT hardness and tensile properties.     

The impact of publicly funded basic research: an integrative extension of Martin and Salter

This paper provides an integrative literature review of the research on the impact of the public funding of basic research, extending previous work done at the Science Policy Research Unit (SPRU), University of Sussex, East Sussex, UK. "Impact" is measured in terms of publications, patents, new drugs, employment, and new start-up companies. The primary focus of this paper is on empirical studies of the impact of biomedical research. However, a few key theoretical papers and empirical papers with a broader industrial focus are also reviewed to provide a more complete perspective. Conclusions, including an alternative view that basic research need not be public supported, and future research opportunities in this area are also discussed.     

Direct volume display devices

Direct volume display devices (DVDDs), which display 3D volumes and surfaces in a volume by providing depth rather than depth cues, are discussed. The transport theory model is used to illustrate why DVDDs are best able to support fast presentation from arbitrary directions. The technology underlying various DVDDs is described. Specifically, the design and operation of the OmniView rotating-screen DVDD are examined. The air-traffic-control/air-tactics-analysis, satellite orbit mechanics, and time-critical target prosecution applications of DVDDs are also discussed     

Characterization of solid-phase welds between Ti---6A1---2Sn---4Zr---2Mo---0.1Si and Ti---13.5A1---21.5Nb titanium aluminide

Dissimilar-alloy welds have been produced between Ti---6Al---2Sn---Z4---2Mo---0.1Si (wt. %) and Ti---13.5Al---21.5 NB (wt.%) titanium aluminde using the three different solid-phase welding processes that create significantly different thermo-mechanical conditions at the weld interface. Exposure to supertransus temperatures, appreciable deformation and rapid cooling of the weld interface region during linear-friction welding promote dynamic recrystallization of beta grains and beta decomposition to fine martensitic products. In contrast, diffusion welding at temperatures below the base metal beta transus temperatures and at relatively low pressures minimizes deformation and microstructural variations in the weld interface region relative to the unaffected base metal. During capacitor-discharge resistance spot welding, extremely rapid heating of the weld interface region to near-solidus temperatures, and subsequent rapid cooling, result in the formation of a metastable, ordered-beta microstructure in the Ti---s13.5Al---21.6Nb and fine alpha-prime martensite in the Ti---6Al---2Sn---4Zr---2Mo-0.1Si.     

Long-term testing and applications of high-stress MV EPR cables

High-stress design 35-kV ethylene propylene rubber (EPR)-insulated cables with 1.14-mm (45-mil) wall reduction have been in service for more than ten years. In the mid 1990s, an extensive cable testing program was initiated to demonstrate that high-stress designs up to 4 kV/mm (101.6 V/mil) exhibit a significant electrical and mechanical safety margin to operate on typical utility network systems. Investigations were also undertaken to demonstrate the suitability of accessories for high-stress designs. This paper will present the results of six-year, long-term wet electrical testing conducted to demonstrate that with proper design, the aging performance of standard wall and high-stress design cables provide satisfactory results and suitable performance for the intended application. Additionally, utility field experience is presented on 35- and 15-kV cables operating at high stress. The experience for these 15-kV medium-voltage EPR cable designs employ the highest recommended stress for cables of this class, as well as taking into account the complete system performance.