LBM investigation of a Cu-water nanofluid over various configurations of pipes in the mixed convection flow

Increasing the heat capacity of heat exchangers is a crucial need for modern devices. The thermal conductivity of the usual fluids and the Nusselt (Nu) number of flows containing such fluids are two bottlenecks in the way of increasing heat delivery in the heat exchangers. For this reason, nanofluids have been introduced. The effect of utilizing a Cu-water nanofluid as a coolant of two hot pipes in a square cavity is investigated numerically with a two-component lattice Boltzmann method. The volume fraction of nanoparticles is assumed to be constant (0.03) while the Richardson (Ri) number varies from 0.02 to 20. Results show that the effectiveness of nanoparticles is better observed in the natural convection mode. However, sedimentation is also very probable at high Ri numbers, which significantly reduces the effectiveness of the nanoparticles. Configurations which produce a natural convection stream similar to the forced convection one as well as the configurations with high spacing and hence, low heat stream interactions, are the best choices for a uniform heat rate from the pipes.     

Mechanical and high velocity impact performance of a hybrid long carbon/glass fiber/polypropylene thermoplastic composite

This research explores mechanical and high velocity impact response of hybrid long carbon/glass fiber-reinforced polypropylene thermoplastic composites (HLFT) with different fiber lengths. The work examines three hybrid long fiber thermoplastic composites, i.e., 5, 10 and 20 mm. The HLFTs were prepared by a combination of extrusion and pultrusion processes and using a cross-head die. Tensile and Izod impact tests were carried out to evaluate the mechanical performance of each HLFT compound. A gas gun with a spherical projectile was used to conduct high velocity impact tests at three velocities of 144, 205 and 240 m/s. The results showed that internal mixing operation caused extensive reduction in fiber length of all three LFT lengths. Tensile strength, modulus and Izod impact test results were the indications of higher values with increase in HLFT length. Comparison of these results for the HLFT with that of corresponding glass/PP LFTs, adopted from earlier work by Shayan Asenjan et al. (J Compos Mater 53:353–360, 2019), showed better performance of HLFT. The high velocity impact results showed a steady higher impact performance with the increase in HFLT fiber length for all impact velocities tested. Comparison of HLFT high velocity impact performance revealed better results for all impact velocities tested with that of the corresponding glass/PP LFT composite.     

Expression of Main Toll-Like Receptors in Patients with Different Types of Colorectal Polyps and Their Relationship with Gut Microbiota

Abnormal activation of Toll-like receptor (TLRs) signaling can result in colon cancer development. The aim of this study was to investigate the expression of important TLRs in different histological types of colorectal polyps and evaluate their relationship with intestinal microbiota. The expression levels of TLR2, 3, 4, and 5 were analyzed in intestinal biopsy specimens of 21 hyperplastic polyp (HP), 16 sessile serrated adenoma (SSA), 29 tubular adenoma (TA), 21 villous/tubulovillous (VP/TVP) cases, and 31 normal controls. In addition, selected gut bacteria including Streptococcus bovis, Enterococcus faecalis, Enterotoxigenic Bacteroides fragilis (ETBF), Fusobacterium nucleatum, Porphyromonas spp., Lactobacillus spp., Roseburia spp., and Bifidobacterium spp. were quantified in fecal samples using absolute qRT PCR, and, finally, the association between TLRs and these gut microbiota- was evaluated by Spearman’s correlation coefficient. Higher expression of TLR2 and TLR4 in VP/TVP and TA, and lower expression levels of TLR3 and TLR5 in all type of polyps were observed. The differences in TLR expression patterns was not only dependent on the histology, location, size, and dysplasia grade of polyps but also related to the intestinal microbiota patterns. TLR2 and TLR4 expression was directly associated with the F. nucleatum, E. faecalis, S. bovis, Porphyromonas, and inversely to Bifidobacterium, Lactobacillus, and Roseburia quantity. Furthermore, TLR3 and TLR5 expression was directly associated with Bifidobacterium, Roseburia, and Lactobacillus quantity. Our results suggest a possible critical role of TLRs during colorectal polyp progression. An abnormal regulation of TLRs in relation to gut microbial quantity may contribute to carcinogenesis.     

Access point selection in the network of Internet of things (IoT) considering the strategic behavior of the things and users

The Journal of Supercomputing - With the expansion in the use of IoT, increasing the efficiency of these networks has become even more significant. Objects need reliable communications at suitable...     

Weekly storage of coolness in heavy brick and adobe walls

Weekly storage of coolness in heavy walls (walls with large thermal inertia or large characteristic time constants or low Fourier numbers) was investigated numerically by considering one-dimensional heat conduction through the walls. The study consisted of first analyzing the heat flow through a single wall and considering various boundary conditions on the inside. The boundary conditions were: constant inside air tempeture throughout the day, variable inside air temperature on a 24-hour cycle, and variable inside air temperature on a 48-hour cycle. Next, the heat flow through walls was studied through a thermal network analysis of a simple building. In this case it was assumed that the ambient air temperature (following a periodic distribution) was increased suddenly and followed this new distribution for many days thereafter.It was concluded that walls with high thermal inertia or time constant can store coolness for several days. The larger the time constant of the wall (for example adobe as compared with brick) the longer it takes for the wall temperature to reach a steady periodic distribution after the change has occurred. However, because of low thermal conductivity of adobe, the retrieval of the stored coolness in these walls is slow, and the mean daily temperature of the room air in the adobe building does not change appreciably beyond seven days after the change. Increase of the wall thickness beyond 50 cm does not improve the thermal performance of the building significantly.     

Characterization of micromachined silicon rectangular waveguide at 400 GHz

We present the first characterization of a micromachined silicon rectangular waveguide at 400GHz. The silicon waveguide has an average loss of 0.086dB/mm for a range of 350-460GHz. The waveguides are formed using well known microfabrication techniques and demonstrate a successful first step towards the use of silicon waveguides as a viable option for THz systems.     

Effect of carbon surface oxidation on platinum supported carbon particles on the performance of gas diffusion electrodes for the oxygen reduction reaction

The effect of carbon surface oxidation on platinum supported carbon particles (Pt/C) with nitric acid was investigated by cyclic voltammetry, electrochemical impedance spectroscopy, polarization experiments and chronoamperometry. Cyclic voltammograms, polarization curves and electrochemical impedance spectra showed that the treated catalyst had much larger active surface area and higher ionic conductivity than the untreated catalyst, and provided enhanced performance for oxygen reduction. The formation of acidic groups was examined by IR spectra. The Pt/C surface oxidation had a large effect on the performance of a gas diffusion electrode for oxygen reduction reaction.     

Synthesis and thermomechanical characterization of polyurethane elastomers extended with α,ω‐alkane diols

A series of polyurethane (PU) elastomers was prepared by the reaction of poly(?‐caprolactone) and 4,4′‐diphenylmethane diisocyanate, which was extended with a series of chain extenders (CEs) having 2–10 methylene units in their structure. The completion of the reaction was confirmed by Fourier transform infrared spectroscopy. The chemical structures of the synthesized PU samples were characterized with Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR spectroscopy, and the thermal properties were determined by thermogravimetric analysis, DSC, and dynamic mechanical thermal analysis techniques. The mechanical properties were also studied and are discussed. The thermogravimetric analysis and DSC analysis showed that CE length had a considerable effect on the thermal properties of the prepared samples. The dynamic mechanical thermal analysis and damping peaks were also affected by the number of methylene units in the CE length. The elastomer extended with 1,2‐ethane diol exhibited optimum thermal properties, whereas the elastomer based on 1,10‐decane diol displayed the worst thermal properties. Tensile strength and elongation at break decreased with increasing CE length, whereas hardness showed the opposite trend. The glass‐transition temperature moved toward lower temperatures with increasing CE length. The decrease in the glass‐transition temperature and tensile properties were interpreted in terms of decreasing hard segments and increasing chain flexibility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

An integrated methodology to control the risk of cardiovascular disease in patients with hypertension and type 1 diabetes

Today, air pollution, smoking, use of fatty acids and ready‐made foods, and so on, have exacerbated heart disease. Therefore, controlling the risk of such diseases can prevent or reduce their incidence. The present study aimed at developing an integrated methodology including Markov decision processes (MDP) and genetic algorithm (GA) to control the risk of cardiovascular disease in patients with hypertension and type 1 diabetes. First, the efficiency of GA is evaluated against Grey Wolf optimization (GWO) algorithm, and then, the superiority of GA is revealed. Next, the MDP is employed to estimate the risk of cardiovascular disease. For this purpose, model inputs are first determined using a validated micro‐simulation model for screening cardiovascular disease developed at Tehran University of Medical Sciences, Iran by GA. The model input factors are then defined accordingly and using these inputs, three risk estimation models are identified. The results of these models support WHO guidelines that provide medicine with a high discount to patients with high expected LYs. To develop the MDP methodology, policies should be adopted that work well despite the difference between the risk model and the actual risk. Finally, a sensitivity analysis is conducted to study the behavior of the total medication cost against the changes of parameters.