Authenticity green coffee bean species and geographical origin using near-infrared spectroscopy combined with chemometrics

To prevent the adulteration of agricultural resources and provide a solution to enhance the green coffee bean supply chain, authentication using the near-infrared spectroscopy (NIRS) technique was investigated. Partial least square with discrimination analysis (PLS-DA) models combined with various preprocessing methods were built from NIR spectra of 153 Vietnamese green coffee samples. The model combined with the standard normal variate and the first order of derivative yielded excellent performance in predicting coffee species with the error cross-validation of 0.0261. PLS-DA model of mean centre and first-order derivative spectra also yielded good performance in verifying geographical indication of green coffee with the error of 0.0656. By contrast, the predicting abilities of post-harvest methods were poor. The overall results showed a high potential of the NIRS in online authentication practices.     

Anaerobic co-digestion of food waste and FOG with sewage sludge – realising its potential in Ireland

The severe environmental pollution in many countries is caused by indiscriminate discharge of large quantities of food waste (FW), fat oil and grease (FOG) and sewage sludge (SS) to the environment. There are many possible treatment routes, but anaerobic digestion (AD) is now well accepted for treating several kinds of organic wastes. But AD of FW alone presents some operational challenges because of substrates and variability. Anaerobic co-digestion of two or more substrates is better than single substrate digestion. This can use a plant’s unused capacity, in line with the trend to renewable energy. Co-digestion technology, although well established in many European countries, is still in its infancy in Ireland. There are problems with different regulatory arrangements. They should be resolved. The paper reviews anaerobic co-digestion technology is reviewed, with special focus on possible application in Ireland.     

Fabrication of tungsten oxide photoanode by doctor blade technique and investigation on its photocatalytic operation mechanism

WO₃ is a potential material candidate for construction of photoanode for solar driven water splitting. In this work, μm-thick porous WO₃ photoanode is prepared by depositing a stable ink made of WO₃ nanoparticles and Aristoflex velvet polymer in water using the doctor blade technique, followed by a sintering in air. The nature of WO₃ nanoparticles, its loading mass on F-doped tin oxide electrode as well as sintering temperature are examined in order to optimize the photocatalytic activity of the resultant WO₃ photoanode. The operation of WO₃ photoanode is investigated by varying the light illumination direction and light incident intensity as well as changing the nature of the electrolyte. Dissolved tungsten in electrolyte is quantified by ICP-MS providing insights into the influences of electrolyte nature and operating conditions to the corrosion of WO₃. It is proposed that the H₂O₂ and OH^. radical generated as by-products of the photo-driven water oxidation on the photoanode surface are harmful species that accelerate the dissolution of WO₃.     

Selective Coating of SnS on the Bio‐Inspired Moth‐Eye Patterned PEDOT:PSS Polymer Films

A new strategy for the selective coating of tin sulfide (SnS) on the surface of moth‐eye patterned (MEP) conducting polymer film is studied by considering the optical properties of the antireflective moth‐eye pattern and flexibility of polymer films. The semiconductor SnS is selectively coated on the surface of MEP microdomes of poly(3,4‐ethylenedioxythiophene) poly(styrene‐sulfonate) (PEDOT:PSS) film. The SnS coated MEP film is obtained by using pore selectively SnS thin layer functionalized polystyrene honeycomb‐patterned porous (HCP) film as a template. Aqueous PEDOT:PSS solution is poured on the SnS functionalized HCP films and detached for the fabrication of SnS coated MEP films. The films show a satisfactory photo‐responsive property under solar stimulated light illumination due to the antireflective MEP structure of PEDOT film and homogenous SnS coating on the surface of the conducting polymer.     

Controlling thickness to tune performance of high-mobility transparent conducting films deposited from Ga-doped ZnO ceramic target

Structure modification has been found to tune significantly the transparent-conducting performance, especially mobility and conductivity of hydrogenated Ga-doped ZnO (HGZO) films. The strong correlation between film thickness and mobility of the films is revealed. The mobility increases quickly with increasing the thickness from 350 to 900 nm, and then tends to be saturated at further thicknesses. A higher mobility than 50 cm²/Vs can be achieved, which is an extra-high value for polycrystalline ZnO films deposited by using the sputtering technique. The thickness-dependent mobility originates from scatterings on grain boundaries and dislocation-induced defects controlled by thin-film growth. Based on the Volmer-Weber model, an expansion model is built up to describe the thickness-dependent crystal growth of the HGZO films, especially at the thick films. As a result, the 800 nm-thick HGZO film obtains the highest performance with high mobility of 51.5 cm²/Vs, low resistivity of 5.3 × 10^?4 Ωcm, and good transmittance of 83.3 %.     

Effect of Supports and Promoters on the Performance of Ni-Based Catalysts in Ethanol Steam Reforming

Ethanol steam reforming (ESR) is one of the potential processes to convert ethanol into valuable products. Hydrogen produced from ESR is considered as green energy for the future and can be an excellent alternative to fossil fuels with the aim of mitigating the greenhouse gas effect. The ESR process has been well studied, using transition metals as catalysts coupled with both acidic and basic oxides as supports. Among various reported transition metals, Ni is an inexpensive material with activity comparable to that of noble metals, showing promising ethanol conversion and hydrogen yields. Additionally, different promoters and supports were utilized to enhance the hydrogen yield and the catalyst stability. This review summarizes and discusses the influences of the supports and promoters of Ni-based catalysts on the ESR process.     

Advanced Surface of Fibrous Activated Carbon Immobilized with FeO/TiO2 for Photocatalytic Evolution of Hydrogen under Visible Light

FeO-doped TiO₂ nanoparticle photocatalysts were immobilized onto the surface of fibrous activated carbon (ACF) via a sol-gel process. As an adsorbent and photocatalyst, FeO-TiO₂ on immobilized ACFs (FeO-TiO₂/ACF) greatly improved the photocatalysis rate of hydrogen production as compared with pure TiO₂ and ACF-TiO₂ under UV irradiation and visible light. The addition of ACFs surface significantly reduced the photogenerated pairs of electrons-hole recombination, thereby promoting the photocatalysis action of doped photo-metal oxides of FeO-TiO₂. Co-doping of FeO onto the lattice of the TiO₂ approach can improve the absorption activity of visible light through photo-metal oxide of TiO₂ and further enhance hydrogen production under visible light. The photocatalytic fabrics (FeO-TiO₂/ACF) were effortlessly split out from the experimental solution for re-utilization and exhibited high stability even after five complete regeneration cycles.     

Nitrogen addition to iron powder by mechanical alloying

Nitrogen was alloyed into iron (a) by mechanical processing in a nitrogen gas environment, and (b) by mechanically alloying with iron-nitride powders to characterize resulting nano-structure and nitrogen distribution. Although the infused nitrogen concentration was significantly greater than the thermodynamic equilibrium solubility of iron, no nitrides formed, even for nitrogen concentrations as high as 4.1 wt.% However, a bctFe phase did form. Lattice expansion calculations indicate that the sum of the interstitial bcc-Fe and bctFe nitrogen concentrations was significantly less than the total measured nitrogen concentration. A considerable portion of the mechanically infused nitrogen was determined to be associated with nanograin boundaries.     

The heroic cancer patient: A critical analysis of the relationship between illusion and mental health.

Examines, in the context of cancer illness, S. E. Taylor and J. D. Brown's (see record 1988-16903-001) claim that mental health is to a degree predicated on illusory beliefs about the self, one's control, and the future. The Heroic Model (HM), a stance toward cancer characterized by belief that positive thoughts and feelings, a fighting spirit, and an optimistic outlook will promote cancer remission, is presented as paradigmatic of Taylor and Brown's thesis. Strong and weak formulations of the HM (the former affirming a direct influence of mental states over physical processes, and the latter affirming indirect effects only) are examined with respect to their potential adaptive value as true or false beliefs, with different consequences for well-being. (French abstract) (PsycINFO Database Record (c) 2010 APA, all rights reserved)