CO2 Hydrogenation over Ru-NPs Supported Amine-Functionalized SBA-15 Catalyst: Structure–Reactivity Relationship Study

Catalysis Letters - We gave an effective protocol to support Ru NPs on amine-functionalized SBA-15 mesoporous silica to catalyze the CO2 hydrogenation reaction. The amine groups present in the...     

Surface Integrity Assessment Upon Electric Discharge Machining of Die Steel Using Non-Destructive Magnetic Barkhausen Noise Technique

Surface integrity characterization of manufactured component is very important as it significantly affects the in-service performance of the component. Till now, surface integrity was evaluated using conventional measurement technique like microhardness tester, X-ray diffraction, optical microscopy and surface roughness tester. But, this technique being laboratory based cannot be used for in-service monitoring of the surface integrity. The present study focuses on the characterization of surface integrity upon electric discharge machined sample using non-destructive magnetic Barkhausen noise technique. Electric discharge machining was performed in die-sinking mode on die steel using copper–tungsten electrode (negative polarity). Experiment was performed by selecting different levels of peak current, gap voltage and pulse on time. Surface integrity characteristics like microhardness change, residual stress, microstructural alteration and surface roughness were analysed using microhardness tester, X-ray diffraction, optical microscopy and surface roughness tester, respectively, and were then correlated with magnetic parameter like root mean square value and peak value obtained from Barkhausen noise signal. The results show a good correlation between magnetic parameter (RMS and Peak value) of Barkhausen noise with the microhardness and surface roughness of the machined sample.

     

Deployment of a cloud pipeline for real-time visual inspection using fast streaming high-definition images

We investigate the challenges of building an end-to-end cloud pipeline for real-time intelligent visual inspection system for use in automotive manufacturing. Current methods of visual detection in automotive assembly are highly labor intensive, and thus prone to errors. An automated process is sought that can operate within the real-time constraints of the assembly line and can reduce errors. Components of the cloud pipeline include capture of a large set of high-definition images from a camera setup at the assembly location, transfer and storage of the images as needed, execution of object detection, and notification to a human operator when a fault is detected. The end-to-end execution must complete within a fixed time frame before the next car arrives in the assembly line. In this article, we report the design, development, and experimental evaluation of the tradeoffs of performance, accuracy, and scalability for a cloud system.     

A comparative study on in vitro behavior of calcium silicate ceramics synthesized from biowaste resources

Calcium silicate ceramics have received significant attention for biomedical applications for their excellent bioactivity and osteoconduction properties. Sol-gel process is extensively used for the fabrication of calcium silicates. In sol-gel process, calcium nitrate tetra hydrate (Ca(NO₃)₂·4H₂O) and tetraethylorthosilicate (TEOS) are used as precursors. However, these precursors are expensive. The objective of this work was to compare in vitro behavior of calcium silicate (CaSiO₃) produced using biowaste such as rice husk ash (RHA) and eggshells (coded; NCS) with CaSiO₃ prepared using TEOS and Ca(NO₃)₂·4H₂O (coded; CCS). Thermal investigation results revealed that the crystallization temperature for NCS is relatively lower (772°C) than for CCS (870°C). Bioactivity was studied in vitro using simulated body fluid (SBF) with respect to mineralization rate of hydroxyapatite. Mineralization of a greater hydroxyapatite was observed on NCS ceramics than CCS ceramics after incubation for 3, 7, 14 days in SBF solution, which was confirmed using X-ray diffractometer, Fourier transform infrared spectroscopy, scanning electron microscopy-energy dispersive spectroscopy. Degradation studies were conducted in Tris-HCl solution and the test results revealed that NCS ceramics has lower dissolution rate than CCS ceramics. The antimicrobial assay has shown that NCS samples exhibit significant zone of inhibition against Escherichia coli and Staphylococcus aureus which confirmed that the CaSiO₃ prepared from RHA and eggshell can prevent bacteria from adhering to the surface. In addition cell culture studies revealed that NCS ceramics possess good cytocompatibility with MG-63 cells and significantly promoted cell proliferation.     

Study of Compatibilized Liquid Crystalline Polymer/Cyclic Olefin Copolymer Blends

The technology to produce compatibilized blends of liquid crystalline polymer and highly amorphous cyclic olefin copolymers through two novel approaches were studied. The first approach was to use silane-functionalized halloysite nanotube as nonspecific compatibilizer and the second method was reactive compatibilization. The study of blends and their resulting microstructure; their thermal, mechanical, and viscoelastic properties were investigated. The kinetic study of blends compatibilized through both routes was performed.     

Cross-layer design: a survey and the road ahead

Of late, there has been an avalanche of cross-layer design proposals for wireless networks. A number of researchers have looked at specific aspects of network performance and, approaching cross-layer design via their interpretation of what it implies, have presented several cross-layer design proposals. These proposals involve different layers of the protocol stack, and address both cellular and ad hoc networks. There has also been work relating to the implementation of cross-layer interactions. It is high time that these various individual efforts be put into perspective and a more holistic view be taken. In this article, we take a step in that direction by presenting a survey of the literature in the area of cross-layer design, and by taking stock of the ongoing work. We suggest a definition for cross-layer design, discuss the basic types of cross-layer design with examples drawn from the literature, and categorize the initial proposals on how cross-layer interactions may be implemented. We then highlight some open challenges and new opportunities for cross-layer design. Designers presenting cross-layer design proposals can start addressing these as they move ahead.