全文获取类型
收费全文 | 66篇 |
免费 | 2篇 |
专业分类
综合类 | 27篇 |
化学工业 | 2篇 |
金属工艺 | 17篇 |
机械仪表 | 1篇 |
武器工业 | 2篇 |
无线电 | 1篇 |
一般工业技术 | 11篇 |
冶金工业 | 7篇 |
出版年
2023年 | 3篇 |
2022年 | 1篇 |
2021年 | 1篇 |
2020年 | 2篇 |
2019年 | 4篇 |
2018年 | 1篇 |
2014年 | 1篇 |
2013年 | 1篇 |
2012年 | 2篇 |
2011年 | 1篇 |
2010年 | 1篇 |
2009年 | 3篇 |
2008年 | 3篇 |
2007年 | 5篇 |
2006年 | 3篇 |
2005年 | 1篇 |
2003年 | 8篇 |
2002年 | 6篇 |
2001年 | 2篇 |
2000年 | 4篇 |
1998年 | 7篇 |
1997年 | 2篇 |
1996年 | 1篇 |
1994年 | 5篇 |
排序方式: 共有68条查询结果,搜索用时 15 毫秒
1.
随着石油产业的快速发展,原油泄露和含油污水严重危害了生态环境和人类健康。因此,含油污水的有效处理成为目前亟待解决的关键问题之一。但传统的油水分离材料普遍存在着油水分离效率低、易造成二次污染、难以回收再利用等缺点,无法满足国家环保标准。近年来,特殊浸润性油水分离材料因具备特殊的选择渗透及吸附性得到了迅速发展。基于此,以表面特殊润湿性油水分离材料为研究基础,对固体表面浸润理论进行了分析,介绍了通过材料表面微观结构调控和化学改性的方法制备特殊浸润性油水分离材料的研究进展,并对特殊润湿性油水分离材料目前面临的挑战及未来的发展方向作了总结和展望。 相似文献
2.
Sr对AZ91镁合金的组织和性能的影响 总被引:2,自引:0,他引:2
借助金相显微镜和扫描电镜研究了Sr对AZ91镁合金铸态组织、热处理后的微观组织及其力学性能的影响.研究结果表明,少量Sr(w(Sr)=0.3%~0.5%)加入可显著细化AZ91镁合金的晶粒,但w(Sr)进一步增加到0.8%时,合金晶粒有粗化倾向,合金组织中出现杆状Al4Sr相.经固溶处理后,合金组织中β Mg17Al12相几乎全部溶于α Mg基体中,金属间化合物Mg17Sr2及 Al4Sr部分溶于基体中,时效处理后从基体中析出,分布弥散、均匀.合金的强度和硬度随Sr含量增加,先增大后减小.其力学性能的变化与Sr加入量和晶界上脆性相的数量有关. 相似文献
3.
4.
To understand the solidification behavior of austenitic stainless steel in rotary electromagnetic-field, the influence of
low-frequency rotary electromagnetic-field on solidification structure of austenitic stainless steel in horizontal continuous
casting was investigated based on industrial experiments. The results show that the solidification structure of austenitic
stainless steel can be remarkably refined, the central porosity and shrinkage cavity can be remarkably decreased, and the
equiaxed grains zone are enlarged by means of application of appropriate low-frequency electromagnetic-field parameters. The
industrial trials verify that the stirring intensity of austenitic stainless steel should be higher compared with that of
plain carbon steel. Electromagnetic stirring affects the macrostructure even if the average magnetic flux density of the electromagnetic
stirring reaches 90 mT (amplitude reaches 141 mT) with the frequency of 3–4 Hz. Due to a higher viscosity, rotating speed
of molten stainless steel is 20%–30% lower than that of molten carbon steel in the same magnetic flux density.
Foundation item: Project(CSTC2007BB4216) supported by the Natural Science Foundation of Chongqing, China 相似文献
5.
镁合金废料回收再生对于提升镁合金废料自身价值和镁资源的可持续发展及环保等方面都具有及其重要的意义。介绍镁合金废料的回收方式、分类和预处理,回顾国内外镁合金废料的回收与再生方法,简单介绍镁合金废料回收质量控制与检测,指出下阶段的研究发展方向。 相似文献
6.
本文采用2kWCO_2激光器对20Cr_(2)Ni_(4)W钢进行了激光表面钴合金化的试验研究。用光学显微镜、扫描电镜、电子探针、X射线衍射、透射电镜、显微硬度计等手段分析了合金化区域的成分、组织和性能。结果表明,激光表面钴合金化可获得含钴均匀的合金化层,合金化层的高温硬度和热疲劳性能均有提高,在热作工具钢表面性能优化领域有着良好的应用前景。 相似文献
7.
热穿孔顶头的失效分析及改进措施研究 总被引:2,自引:0,他引:2
对穿孔无缝钢管热穿孔顶头的失效机制和使用状况进行了分析研究,认为穿孔顶头的失效形式主要表现为顶头塌鼻,粘钢,开裂,提出了利用稀土铝合金化提高顶头使用寿命的措施,并对该措施的可行性进行了论证。 相似文献
8.
涂装是提高镁合金耐蚀性和装饰性的最经济有效的方法。涂装前处理对涂装质量影响很大,文中对镁合金的涂装前处理工艺进行了分析。 相似文献
9.
10.