Spray dryer processed graphene oxide/reduced graphene oxide for high-performance supercapacitor

This study deals with the utility of mini spray dryer process to improve the dispersibility, of graphene oxide(GO) and its application for high-performance supercapacitor. Initially, the neutral solution of GO was obtained using the modified Hummer's method. After this, the prepared GO solution was processed by mini spray dryer to obtain a more purified, lighter, and dispersed form of GO which is named as spray dryer processed GO (SPGO). The SPGO thus obtained showed excellent dispersibility behavior with various solvents, which is not found in case of conventional oven drying. Furthermore, utility of SPGO and its reduced form (r-SPGO) for supercapacitor applications have been investigated. Results obtained from the cyclic voltammetry(CV) analysis, impedance, and charge-discharge behavior of supercapacitor fabricated using r-SPGO shows enhanced features. Therefore, the simple spray dried GO and its reduced form, that is, r-SPGO can be utilized as a potential candidate for the supercapacitor application. Herein, as synthesized SPGO exhibited the specific capacitance of 12.07 and 37.6 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively, at a scan rate of 5 mV/s. On the other hand, reduced form of SPGO, that is, r-SPGO showed the specific capacitance of 27.16 and 230 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively.     

Enhancement of thermal,mechanical, ignition and damping response of magnesium using nano-ceria particles

Magnesium (Mg)-based nanocomposites owing to their low density and biocompatibility are being targeted for transportation and biomedical sectors. In order to support a sustainable environment, the prime aim of this study was to develop non-toxic magnesium-based nanocomposites for a wide spectrum of applications. To support this objective, cerium oxide nanoparticles (0.5?vol%, 1?vol%, and 1.5?vol%) reinforced Mg composites are developed in this study using blend-press-sinter powder metallurgy technique. The microstructural studies exhibited limited amounts of porosity in Mg and Mg-CeO₂ samples (< 1%). Increasing presence of CeO₂ nanoparticles (up to 1.5?vol%) led to a progressive increase in microhardness, dimensional stability, damping capacity and ignition resistance of magnesium. The compressive strengths increased with the increasing addition of the nanoparticles with a significant enhancement in the fracture strain (up to ~48%). Superior energy absorption was observed for all the composite samples prior to compressive fracture. Further, enhancement in thermal, mechanical and damping characteristics of pure Mg is correlated with microstructural changes due to the presence of the CeO₂ nanoparticles.     

High slew-rate CMOS operational amplifier

A 0.8 /spl mu/m CMOS operational amplifier configuration with a slew rate in excess of 2 V/ns and a unity gain bandwidth of 55 MHz with a load capacitance of 15 pF is proposed. This employs a dynamic technique that turns on a large current source when the rate of change of input is larger than a pre-decided value.     

Mixed oxide supported hydrodesulfurization catalysts—a review

Support effects form important aspect of hydrodesulfurization (HDS) studies and mixed oxide supports received maximum attention in the last two decades. This review will focus attention on studies on mixed oxide supported Mo and W catalysts. For convenience of discussion, these are divided into Al₂O₃ containing mixed oxide supports, TiO₂ containing mixed oxide supports, ZrO₂ containing mixed oxide supports and other mixed oxide supports containing all the rest. TiO₂ containing mixed oxides received maximum attention, especially TiO₂–Al₂O₃ supported catalysts. A brief discussion about their prospects for application to ultradeep desulfurization is also included. An overview of the available literature with emphasis on research carried out in our laboratory form the contents of this publication.     

Cut off frequency and transit time analysis of lightly doped drain (LDD) MOSFETs

Analytical model for the transconductance, cut off frequency, transit time and fringing capacitance of LDD MOSFETs is presented with a simple approach. The analysis is carried out considering the LDD device as a conventional MOSFET with a series resistance [Z.-H. Liu et al., Threshold voltage model for submicrometer MOSFETs. IEEE Trans Electron Devices 1993; ED-40: 86–94] and a simple closed form expressions for cut off frequency and transit time is obtained. The total gate capacitance, i.e. the geometric and fringing capacitance, is calculated for both LDD and non-LDD devices and lower fringing capacitance is reported in LDD devices. Lower cut-off frequencies and higher transit time are reported in LDD devices for the same channel length.     

Effect of dopants on the low temperature microwave dielectric properties of Ba(Zn1/3Ta2/3)O3 ceramics

Ba(Zn_1/3Ta_2/3)O₃ has been prepared with different dopants that gave best microwave dielectric properties at room temperature. Effects of different dopants on the low temperature microwave dielectric properties of BZT were investigated. With decrease in temperature, loss tangent was found to decrease marginally and then increase at temperatures lower than 100 K. Increase in loss factor at lower temperatures were found to be less for dopants with smaller ionic radii. Dielectric constant was found to be almost independent of temperature. Temperature coefficient of resonant frequency slowly decreased from a positive value to negative value when temperature was lowered. Temperature at which τ_f becomes zero was found to vary for different dopants. There is a temperature stable region for tanδ, ɛ_r and τ_f which varies for different dopants.     

A backbone-reversed all-{beta} polypeptide (retro-CspA) folds and assembles into amyloid nanofibres

The backbone-reversed or ‘retro’, form of a modelall-ß-sheet protein, Escherichia coli CspA, was producedfrom a synthetic gene in E.coli in fusion with an N-terminalaffinity tag. Following purification under denaturing conditionsand dialysis-based removal of urea, the protein was found tofold into a soluble, poorly structured multimer. Upon concentration,this state readily transformed into amyloid nanofibres. CongoRed-binding amorphous forms were also observed. Since a ß-sheet-formingsequence is expected to retain high ß-sheet-formingpropensity even after backbone reversal and given the fact thatfolding of retro-CspA occurs only to a poorly structured form,we conclude that the increase effected in protein concentrationmay be responsible for the formation of intermolecular ß-sheets,facilitating the bleeding away of the protein’s conformationalequilibrium into aggregates that generate well-formed fibres.Since every molecule in these fibres contains a peptide tagfor binding Ni²⁺, the fibres may provide a template for depositionof nickel to generate novel materials. Received April 1, 2003; revised October 27, 2003; accepted October 30, 2003     

Synthesis and characterization of acidic properties of Al-SBA-15 materials with varying Si/Al ratios

Al-SBA-15 of varying Si/Al ratios in the range 11.4–78.4 was synthesized using tri-block copolymer P123. The calcined materials were examined by XRD, pore size distribution, surface area, ²⁷Al NMR spectroscopy. The acidity and acid strength distribution were studied using microcalorimetric adsorption of NH₃. The acidic properties were also examined by cumene cracking reaction as a function of Si/Al ratios. Systematic variation of acidity and activity was observed as a function of Si/Al ratio. The initial heats of NH₃ adsorption correlated well with activity indicate that acid sites with ΔH > 100 kJ/mole is responsible for cumene cracking activity. Linear correlations were obtained with total acidity and cumene cracking activities. The tetrahedral aluminum was found to be responsible for the observed acidities and catalytic activities.     

Reengineering the Internet for Better Security

The growing proliferation of malware is raising doubts about the Internet's future. Security measures primarily target inbound traffic, but service providers have no incentive to stop attacks and spam at the source. A proposed certification scheme motivates providers to control outgoing traffic, efficiently increasing overall security while preserving the Internet's open, decentralized structure     

Gelation and phase separation in maltodextrin-caseinate systems

A range of rheological techniques, including small deformation isothermal runs following quenching, controlled rate heating profiles, mechanical spectra, and large deformation strain sweeps and creep compliance testing, were employed in the investigation of maltodextrin—sodium caseinate aqueous dispersions. The concentration dependence, viscoelastic ratio and melting profiles of shear moduli for concentrated maltodextrin samples suggest a highly aggregated, enthalpically linked biopolymer gel. By contrast, the caScinate particles form a ‘pasty’ solid at low temperatures with a high viscous component, which upon moderate heating reverts readily into an entropically driven liquid body. Mixing of the polymers results in a composite system whose phase inversion from a maltodextrin continuous network with discontinuous protein inclusions to a caScinate dispersion suspending the polysaccharide particles is determined by the weight ratio of the two components in the blend. The overall strength of the composite has been related to the mechanical functions of the individual components, and the idea of kinetically trapped mixed gels has been put forward to rationalize the solvent partition between the two constituent phases. Results were used to advance the conclusions reached from work on other mixed biopolymer systems carried out in this laboratory.