三峡散装物料集装箱的规范使用与保养

三峡工程是我国第一个使用散装物料集装箱的水利水电工程。基于对散装物料集装箱使用状况和维修情况的分析从箱体清洁、锈蚀、超载、零部件的遗失及损坏、检查、流化床、气压试验、保养等八个方面对散装物料集装箱的规范使用与保养中存在的问题进行论述，并提出相应解决的办法。     

基于ANSYS的铸嘴流体耦合场三维有限元仿真分析

作者用大型有限元分析软件ANSYS对铸嘴内稳态层流铝熔体进行仿真分析。实现了三维建模。解决了三维热一流耦合求解的问题，得到铝流体的速度、压力及温度的分布图。分析了铸嘴出口速度和温度的分布规律及其对连续铸轧的影响。     

连续铸轧流变行为的物理模拟及其应力-应变关系的演变

在Gleeble-1500热/力机上用专制的夹具系统对铝合金铸轧过程流变行为及其影响因素进行了系列的模拟实验研究,得到了不同变形条件下铝合金瞬态凝固连续固态流变成形过程中的形变规律.实验表明铝合金的[液-糊状-固]流变过程存在4个不同特征阶段,通过对实验数据进行多元线性回归分析,建立了适用于连续铸轧这一特定工况条件下铝合金流变本构方程.     

Model-based parameter identification of comprehensive friction behaviors for giant forging press

A new experimental apparatus was set up to investigate the actual fi-iction characteristics on the basis of speed control of the serve system.A modified friction model was proposed due to real time varying deformation resistance.The approach to identify the parameters of comprehensive friction behaviors based on the modified model was proposed and applied to the forging press.The impacts on parameters which the external load had were also investigated.The results show that friction force decreases with velocity in the low velocity regime whereas the friction force increases with the velocity in the high velocity regime under no external load.It is also shown that the Coulomb friction force,the maximum static friction force and the vicious friction coefficient change linearly with the external load taking the velocity at which the magnitude of the steady state friction force becomes minimum as the critical velocity.     

浅谈校园网的规划设计与管理

随着网络技术迅速发展,校园网的建设已成为各级各类学校实现教育现代化、管理信息自动化不可缺少的基础设施之一。概述了校园网的规划设计方法,对校园网的硬件和软件的设施提出了需求,最后介绍了校园网的安全、故障维护和流量管理的方法,并对校园网的日常管理维护提出了自己的见解。     

Rheological behavior of continuous roll casting process of aluminum alloy

The rheological behavior of aluminum alloy and its influencing factors in physical simulation of continuous roll casting process were studied by using a Gleeble-1500 thermal-mechanical simulation tester with a set of special clamp system. The relationships between the flow stress and the strain rate in the deformation process of simulating roll casting experiment were obtained. The results show that four different characteristic stages exist in the temperature range of the whole rheological process. The first occurs when the temperature is higher than 600℃, which belongs to the creep deformation stage; the second occurs when the temperature lies in the range of 500 - 600℃, and it can be regarded as the high temperature and low stress level deformation stage; the third occurs when the temperature decreases to the range of 300 - 500℃, it is considered to be the middle stress level deformation stage; the last occurs when the temperature is less than 300℃ and the strain rate is less than 1.00 s^-1 , it belongs to middle stress level deformation stage. But when the strain rate is larger than 1.00 s^-1, it belongs to the high stress level deformation stage. And the relative constitutive models suitable for the four different stages of continuous roll casting process were established through multivariate linear regression analysis of the experimental data.     

模糊PID在液压机位置控制系统中的应用

大型模锻液压机活动横梁的位置控制与运行可靠性对产品精度至关重要,针对活动横梁位置控制高精度、大滞后和大惯性等特点,提出了基于位移反馈的五驱动缸主动平衡系统.结合PID和模糊控制的优点,设计开发了基于S7-300 PLC的模糊PID参数自整定控制算法,利用模糊推理对PID参数K<,P>,T<,I>和T<,D>进行在线自整...     

循环带传输系统

针对短半衰期核素实验研究的特点,设计了一套新的收集和测量带系统,此系统采用低负载以及循环带结构,从而缩短了传输所需时间,大幅减少了收集带的更换频率.使之可以用于半衰期在0.2s以上的短半衰期核素的研究.     

工艺参数对蠕变时效2124铝合金力学性能和微观组织的影响

研究2124铝合金在蠕变时效过程中工艺参数对力学性能和微观组织的影响。结果表明，蠕变量和蠕变速率随着时效时间、温度、应力的增大而增大。硬度随着时间和应力的增加呈类似于先增加后减小的趋势。在实验温度185～195℃范围内，温度对硬度的影响不大。当蠕变条件为200MPa、185℃、8h时，试样得到最佳的力学性能，此时试样基体内同时存在强化相S＂相和S＇相。透射电镜观察表明外加应力能促进析出相的析出和长大，基体中没有发现明显的应力位向效应。     

拉压应力下7B50铝合金应力松弛时效行为研究

通过应力松弛实验、力学性能测试和透射电子显微镜组织观察并研究了不同初始应力水平和温度条件下7B50铝合金的拉伸和压缩应力松弛、时效析出及其强化行为.结果 表明:拉伸和压缩应力松弛时效行为存在不对称性,前期拉应力松弛速率大于压应力松弛速率,但拉应力松弛速率下降较快;后期的拉应力松弛速率小于压应力松弛速率,使得两者应力松弛...