Repulsive Flux Pinning Force in NbTi/Nb Superconductor/Superconductor Multilayers

Flux pinning characteristics have been investigated for the Nb _x Ti_100-x /Nb(x = 65, 50 and 28) and Nb ₂₈ Ti ₇₂/Nb ₆₅ Ti ₃₅ superconductor(S)/superconductor(S^′) multilayers. The maximum of the pinning force F _{p⊥ max} perpendicular to the layer plane as a function of the structure modulation length λ has a peak in the quasi-two-dimensional region (λ～20 nm). The maximum. values of the F _{p⊥ max} versus λ curve are proportional to the difference of the GL coherence length (ξ _GL ) between the superconductive sublayers S and S^′. The results suggest that the large F _{p⊥ max} in the S/S^′ multilayer is caused by the repulsive pinning force due to Nb layers with larger ξ _GL .     

Coating of hydroxyapatite on metal plates using thermal dissociation of calcium-EDTA chelate in phosphate solutions under hydrothermal conditions

Coating of hydroxyapatite on various metal plates was carried out by a homogeneous precipitation technique using hydrothermal reactions in Ca(edta)^2-–NaH₂PO₄ at 140–200°C and pH 3.4–10.0. Hydroxyapatite films were formed on the surface of the iron plates in solutions at an initial pH above 4.7, whereas aggregates consisting of needle-like hydroxyapatite crystal radiating from a point in the form of flower deposited as islands on the surface of aluminum, copper and titanium plates. The upper part of the film formed on the surface of the iron plates consisted of needle-like hydroxyapatite particles whereas the bottom of the film consisted of spherical hydroxyapatite particles. The length of the needle-like hydroxyapatite particles increased with decreasing concentration of Ca(edta)^2-.     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

Complexity of the color appearance of objects with nonuniform illumination

An inversion relationship is clarified between lightness and brightness, and also between chroma and colorfulness under nonuniform illumination with different illuminance levels (high and low) within the same visual field. Brightness (or colorfulness) of object color with low lightness (or chroma) under high illuminance level is perceived higher than that of another object color with high lightness (or chroma) under low illuminance level. Two color images are given for showing the inversion phenomena on brightness–lightness and colorfulness–chroma between object colors under different illuminance levels. These color images are useful for making researchers on color understand the differences in concept between brightness and lightness, and also between colorfulness and chroma. In particular, the concept of colorfulness is important, but difficult to understand. © 2007 Wiley Periodicals, Inc. Col Res Appl, 32, 372–377, 2007     

Effect of 8 MeV electron irradiation on electrical properties of CuInSe2 thin films

Radiation damages due to 8 MeV electron irradiation in electrical properties of CuInSe₂ thin films have been investigated. The n-type CuInSe₂ films in which the carrier concentration was about 3×10¹⁶ cm⁻³, were epitaxially grown on a GaAs(0 0 1) substrate by RF diode sputtering. No significant change in the electrical properties was observed under the electron fluence <3×10¹⁶ e cm⁻². As the electron fluence exceeded 10¹⁷ e cm⁻², both the carrier concentration and Hall mobility slightly decreased. The carrier removal rate was estimated to be about 0.8 cm⁻¹, which is slightly lower than that of III–V compound materials.     

Aspects of gasification and structure in cokes from coals

Cokes were prepared from nine coals of different rank and characterized by surface area measurement, reactivity to carbon dioxide at 1473K and Raman-laser spectroscopy. Rates of gasification of cokes on a unit surlface area basis (K¹ = g m^?2 min^?1) decreased with increasing rank of parent coal based on maximum oil reflectances. However rates of gasification could not be related to coke structure as measured by Raman-laser spectroscopy.     

Preparation and characterization of natural rubber dispersed in nano-matrix

Preparation of a model nano-matrix-dispersed polymer was investigated in terms of graft-copolymerization of deproteinized natural rubber latex with styrene, using tert-butyl hydroperoxide/tetraethylenepentamine as an initiator. The products were characterized by ¹H-NMR spectroscopy and size-exclusion-chromatography after ozonolysis. The grafting efficiency of styrene was found to be more than 90% under the best condition of the graft-copolymerization. The morphology of the film specimens, prepared from graft-copolymers, was observed by transmission electron microscopy after staining the films with OsO₄. Natural rubber particle of about 0.5 μm in diameter was dispersed in polystyrene matrix of about 15 nm in thickness.     

Effect of fatty acids on the strain‐induced crystallization of natural rubber detected by tear energy measurements

The strain‐induced crystallization of natural rubber (NR) was investigated by the measurement of the tear energy of a crosslinked blend consisting of NR and noncrystalline styrene–butadiene rubber (SBR). When NR was dispersed into the SBR matrix, the tear energy of SBR increased at various temperatures and tear rates. After the application of the principle of time–temperature superposition to the tear energy according to the Williams–Landel–Ferry equation, two distinct curves were found for the NR/SBR blend with respect to the reduced tear rate, despite the fact that the tear energy of SBR or the SBR/SBR blend gave its own single composite curve. When the fatty acid in the NR/SBR blend was removed by acetone extraction, the tear energy of the blend drew a single composite curve. The conversion of the two curves into the single composite curve for the NR/SBR blend suggested that the tear energy depended on the strain‐induced crystallization of NR dispersed in the SBR matrix, which was suppressed by the removal of the fatty acid. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 613–619, 2005     

Analysis of surface integrity for minimum quantity lubricant—MQL in grinding

The quality of machined components is currently of high interest, for the market demands mechanical components of increasingly high performance, not only from the standpoint of functionality but also from that of safety. Components produced through operations involving the removal of material display surface irregularities resulting not only from the action of the tool itself, but also from other factors that contribute to their superficial texture. This texture can exert a decisive influence on the application and performance of the machined component. This article analyzes the behavior of the minimum quantity lubricant (MQL) technique and compares it with the conventional cooling method. To this end, an optimized fluid application method was devised using a specially designed nozzle, by the authors, through which a minimum amount of oil is sprayed in a compressed air flow, thus meeting environmental requirements. This paper, therefore, explores and discusses the concept of the MQL in the grinding process. The performance of the MQL technique in the grinding process was evaluated based on an analysis of the surface integrity (roughness, residual stress, microstructure and microhardness). The results presented here are expected to lead to technological and ecological gains in the grinding process using MQL.