Temperature-responsive culture surfaces for insect cell sheets to fabricate a bioactuator

ABSTRACT

For the first time, we have fabricated insect-derived cell sheets by using temperature-responsive culture surfaces having a phase-transition temperature below 25°C. We prepared the temperature-responsive cell culture surfaces (tissue culture polystyrene, TCPS) by grafting a copolymeric gel consisting of hydrophobic N-tert-butylacrylamide (tBAAm) and N-isopropylacrylamide (IPAAm) units. First, to characterize the hydrophilic and hydrophobic properties of the copolymeric gel-grafted surfaces, static water contact angles of each surface were measured at various temperatures. By increasing the amount of tBAAm in the grafted copolymeric gel, the transition temperature of the gel was shifted to lower temperatures. At 25°C, the grafted copolymeric gel was dehydrated, and the insect-derived cells (AeAl2 cells) adhered on all the copolymeric gel-grafted surfaces. At 20°C, AeAl2 cells cannot adhere on the P(IPAAm-1.62tBAAm)-TCPS surface (the initial molar ratio of IPAAm and tBAAm (tBAAm?=?1.62 mol%)) better than on other surfaces (TCPS and tBAAm?=?4.88, 8.17 mol%). These two findings implied that the lower critical solution temperature of the copolymeric gel-grafted-TCPS existed from 20°C to 25°C. The laminin-coated P(IPAAm-1.62tBAAm)-TCPS surface showed temperature-dependent cell attachment and detachment properties, while AeAl2 cells were not detached from the extracellular matrix uncoated P(IPAAm-1.62tBAAm)-TCPS surface. AeAl2 cells and insect muscle cells were harvested as the respective sheets.     

Stabilizing effect of the cyclodextrins additive to spray-dried particles of curcumin/polyvinylpyrrolidone on the supersaturated state of curcumin

Although curcumin is considered to have various therapeutic effects, its use as a functional food or supplement is restricted owing to its low water solubility and bioavailability. To increase the solubility of curcumin in water, the use of polyvinylpyrrolidone (PVP) and vinylpyrrolidone-vinyl acetate copolymers with a pyrrolidone skeleton was noted to be promising. In particular, the bi-component formulations of curcumin/PVP prepared through spray drying exhibited an amorphous state in powder X-ray diffraction observations and temporally increased the apparent solubility of curcumin to over 5000 times that of untreated curcumin; nevertheless, after 24 h, the solubility decreased owing to the unstable supersaturated state of curcumin. The addition of α-cyclodextrin (α-CyD) in the bi-component curcumin/PVP formulation helped maintain the supersaturated state of curcumin, whereas the addition of β- and γ-CyD led to the collapse of the supersaturated state. The addition of α-CyD can likely help inhibit the nucleation and crystal growth of curcumin, through the interaction among the solubilized units of curcumin/PVP and α-CyD.     

利用核函数法中的自适应带宽同时对一维空间两个储集层属性参数进行粗化

在多孔介质流体流动模拟中,应用网格粗化方法必须在保留重要储集层参数的空间分布的前提下,首先利用大网格粗化原始地质模型(尤其是孔隙型介质),并用数值方法求解。提出了根据属性参数的空间分布、以核函数的自适应带宽为基础的网格粗化新方法,该方法既减少了网格数量,同时也保留原始精细模型的主要非均质性特征。该方法的关键点在于可以同时对两种储集层属性参数进行网格粗化。首先计算每个储集层属性参数的带宽量或最优门槛值并得到粗化结果,然后根据最大带宽和最小带宽采用两种不同的方法对两个属性参数同时粗化。现在已经能够实现利用不同方法建立储集层两个属性参数的最终粗化模型,不同方法的网格单元数和网格位置都相同。最小带宽法的粗化误差小于最大带宽法。图6表1参29     

Influence of Cu metal on the domain structure and carrier mobility in single-layer graphene

We demonstrate that domain structure of single-layer graphene grown by ambient pressure chemical vapor deposition is strongly dependent on the crystallinity of the Cu catalyst. Low energy electron microscopy analysis reveals that graphene grown using a Cu foil gives small and mis-oriented graphene domains with a number of domain boundaries. On the other hand, no apparent domain boundaries are observed in graphene grown over a heteroepitaxial Cu(111) film deposited on sapphire due to unified orientation of graphene hexagons. The difference in the domain structures is correlated with the difference in the crystal plane and grain structure of the Cu metal. The graphene film grown on the heteroepitaxial Cu film exhibits much higher carrier mobility than that grown on the Cu foil.     

Rubber‐toughened polyamide‐6 with a low thermal expansion coefficient: effect of preferential distribution of rubber and inorganic filler

The effects of morphological changes on the thermal expansion, toughness and heat resistance of polyamide‐6 (PA)/styrene–ethylene–butylene–styrene (SEBS)/polyphenylene ether (PPE) blends were investigated. Compared with the typical ‘sea (PA matrix)–island (PPE domain)–lake (SEBS in PPE domain)’ morphology, an injection‐molded ternary blend with a preferential distribution of SEBS component at the interface between PA and PPE exhibited a low coefficient of linear thermal expansion (CLTE) in the flow direction. This low CLTE was ascribed to the deformation of SEBS and PA into a co‐continuous microlayer network structure during injection molding. Consequently, the expansion preferentially occurred towards the thickness direction. Further CLTE reduction either by a change in PA viscosity or by the selective location of an inorganic filler was examined, and its influences on impact strength and heat resistance are discussed based on transmission electron microscopy observations. © 2015 Society of Chemical Industry     

Experimental study on method of estimating strength of weld metal in steel structure

We conducted the welding experiment using three kinds of test piece, actual size, diaphragm and butt joint. Then, we examined the influence on strength, cooling time and carbon equivalent of weld metal by welding conditions on the different test pieces. We calculated an estimate of cooling time and chemical components. Consequently, we concluded that the strength of weld metal can be estimated by heat input, interpass temperature, carbon equivarent of welding wire and shape of test piece.     

Functional binders for reversible lithium intercalation into graphite in propylene carbonate and ionic liquid media

Poly(acrylic acid) (PAA), poly(methacrylic acid) (PMA), and poly(vinyl alcohol) (PVA), which have oxygen species as functional groups, were utilized as a binder for graphite electrodes, and the electrochemical reversibility of lithium intercalation was examined in PC medium and ionic liquid electrolyte, lithium bis(trifluoromethanesulfonyl)amide dissolved in 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl)amide (BMP-TFSA). Columbic efficiency of 75–80% with more than 300 mAh g^?1 was achieved upon first reduction/oxidation cycle in both electrolytes using these binding polymers, which were significantly improved in comparison to a conventional PVdF binder (less than 45% of columbic efficiency for the first cycle). For the graphite-PVdF electrode, co-intercalation and/or decomposition of PC molecules solvating to Li ions were observed by the electrochemical reduction, resulting in the cracking of graphite particles. In contrast, the co-intercalation and decomposition of PC molecules and BMP cations for the first reduction process were completely suppressed for the graphite electrodes prepared with the polymers containing oxygen atoms. It was proposed that the selective permeability of lithium ions was attained by the uniform coating of the graphite particles with PAA, PMA, and PVA polymers, because the electrostatic interaction between the positively charged lithium ions and negatively charged oxygen atom in the polymer should modulate the desolvation process of lithium ions during the lithium intercalation into graphite, showing the similar functions like artificial solid-electrolyte interphase.     

FRVT 2006: Quo Vadis face quality

A study is presented showing how three state-of-the-art algorithms from the Face Recognition Vendor Test 2006 (FRVT 2006) are effected by factors related to face images and people. The recognition scenario compares highly controlled images to images taken of people as they stand before a camera in settings such as hallways and outdoors in front of buildings. A Generalized Linear Mixed Model (GLMM) is used to estimate the probability an algorithm successfully verifies a person conditioned upon the factors included in the study. The factors associated with people are: Gender, Race, Age and whether they wear Glasses. The factors associated with images are: the size of the face, edge density and region density. The setting, indoors versus outdoors, is also a factor. Edge density can change the estimated probability of verification dramatically, for example from about 0.15 to 0.85. However, this effect is not consistent across algorithm or setting. This finding shows that simple measurable factors are capable of characterizing face quality; however, these factors typically interact with both algorithm and setting.