Cooperative Diversity in Secondary Systems: Efficient Relaying Protocol for Cognitive Radio

Wireless Personal Communications - This paper considers half-duplex cooperative spectrum sharing scheme where both primary and secondary systems mutually cooperate with each other to exploit...     

Electromechanical analytical model of shape memory alloy based tunable cantilevered piezoelectric energy harvester

International Journal of Mechanics and Materials in Design - The resonant frequency of electromechanical energy harvester should be tuned to ambient frequency so as to maximize the harvester power....     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Conversion of acrylonitrile-based precursors to carbon fibres

The progress of stabilization of two compositions of acrylic fibres with various orientations has been followed by a variety of techniques. The thermooxidative treatments for stabilization have been carried out in a continuous process and also in a batch process under free shrinkage, constant length and constant tension conditions. The morphological model of acrylic fibres consists of an alternating sequence of laterally ordered and laterally disordered regions along the fibre direction. This structure is consistent with the observations based on small-angle X-ray scattering of copper- impregnated precursor fibres and thermomechanical response, thermal stress development, calorimetry, wide- and small-angle X-ray scattering and sonic modu-lus measured at different extents of stabilization. Lateral as well as orientational order in these fibres can be increased markedly through a high-temperature deformation process prior to stabilization. An increase in perfection and extent of order is observed in the early stages of stabilization. There is also a simultaneous decrease in the orientation of the disordered phase at this stage and the extent of this decrease depends on the axial constraints imposed on the fibre. Little difference in the rate of stabilization is observed as measured by density or oxygen uptake for fibres with different extents of orientation, lateral order or restraint. Fibres containing itaconic add, a stabilization catalyst did show an increased rate of stabilization. Inferences have been drawn regarding additional research pertaining to achieving high order in precursor fibres, minimizing orientational relaxation during oxidative stabilization, and the techniques for monitoring the extents of the stabilization treatment and the changes in relevant morphological parameters.     

D.c. conduction studies on thermally evaporated neodymium oxide thin films

Aluminium-neodymium oxide-aluminium thin film capacitors have been prepared by thermal evaporation and the d.c. conduction properties of these films have been studied. The thicknesses of the films have been determined by a multiple beam interferometer. The current-voltage power-law dependence showed that the conduction in these films is space-charge limited. The linear dependence of the current density on the square root of the applied field confirmed the exponential trap distribution. The trap density has been found to be of the order of 10²⁶ m^–3. It has also been observed that the Schottky type of conduction is predominant in the high-field region and the height of the Schottky barrier has been determined. It is seen that the conduction mechanism is an activated process with the activation energy decreasing with increasing field.     

Universal sine squared shaped video syncs

A digital method for generating precisely controlled sine-squared shaped video sync pulses of sixteen different wave shapes is reported. The principle involved in the technique is to store 16 sample values of the desired sine-squared shaped signal in programmable read-only memory (PROM) and to release these digital data sequentially to a digital-to-analog converter at a desired speed to produce the sine-squared shaped waveform. The application of this method is discussed     

Halogen-free acylation of toluene over FeSBA-1 molecular sieves

Three-dimensional cage type iron substituted mesoporous silica with different iron contents (FeSBA-1) was synthesized in a highly acidic media using cetyltriethylammonium bromide and tetraethylorthosilicate as a template and a silica source, respectively. Acylation of toluene with acetic anhydride (AA) was carried out over FeSBA-1 mesoporous catalysts with different n_Si/n_Fe ratios in the temperature range 80–180 °C for a time-on-stream of 1–6 h under liquid phase conditions. The important factors affecting the conversion and the selectivity of the reaction, such as the reaction temperature, feed ratio, catalyst weight and time-on-stream were studied and the results are discussed in detail. The reaction conditions were optimized and the n_AA/n_Toluene ratio of 2 and catalyst weight of 0.1 g (3.3 wt% of total reaction mixture) were maintained for all catalytic runs. It was found that the catalytic activity is strongly influenced by the amount of tetrahedral iron in the catalysts. Among the catalysts used in the present study, FeSBA-1(36) showed a high toluene conversion and selectivity to p-methylacetophenone (p-MAP) under the optimized reaction conditions. It was also found that the selectivity for p-MAP was always higher than m-MAP and o-MAP for all the catalysts and the activity of the catalysts changes in the following order: FeSBA-1(36) > FeSBA-1(90) > FeSBA-1(120).     

Effect of irrigation scheduling on grain yield and nitrogen use efficiency of irrigated wheat at Kadawa and Bakura,northern Nigeria

In this study the interaction of applied N with different irrigation schedules on grain yields and N use efficiency of wheat was investigated in two Inceptisols of the Nigerian savanna during 1978–80. Irrigation intervals ranged from 7 to 28 days at Kadawa and 5 to 10 days at Bakura while the N rates varied from 0 to 200 kg per ha. Both grain yield and N uptake increased significantly with increasing N rates at both the locations. The magnitude of increase in yield and N uptake decreased substantially when the irrigation interval became longer. This interaction was very pronounced at Bakura where the soil is highly porous, excessively drained and extremely poor in moisture retention capacity. Longer irrigation intervals produced grains with slightly higher N content but the difference was not significant. Higher N rates and fewer irrigations gave lower fertilizer N recovery.