Anti beta 2glycoprotein I antibodies and lupus anticoagulant in patients with recurrent pregnancy loss: prevalence and clinical significance

Over 2000 electrocution deaths were identified among U.S. construction workers from 1980 to 1991, with the highest mean annual crude mortality rate (2.5 per 100,000 people), and second highest mean age-adjusted rate (2.7 per 100,000 people) of all industries. Although the crude fatality rates showed a downward trend, construction workers are still about four times more likely to be electrocuted at work than are workers in all industries combined. Nearly 40% of the 5083 fatal electrocutions in all industries combined occurred in construction, and 80% were associated with industrial wiring, appliances, and transmission lines. Electrocutions ranked as the second leading cause of death among construction workers, accounting for an average of 15% of traumatic deaths in the industry from 1980 to 1991. The study indicates that the workers most at risk of electrical injury are male, young, nonwhite, and electricians, structural metal workers, and laborers. The most likely time of injury is 11 a.m. to 3 p.m. from June to August. Focusing prevention on these populations and characteristics through better methods of worker and supervisor electrical safety training, use of adequate protective clothing, and compliance with established procedures could minimize the average annual loss of 168 U.S. construction workers.     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

Interplay of YBCO and Embedded 211 Particles in Melt-Textured YBCO Superconductors

Local orientations of superconducting YBa₂Cu₃O _x (123) and embedded Y₂BaCuO₅ (211) particles within bulk, melt-textured 123 samples are studied on a local scale by means of electron backscatter diffraction (EBSD). The embedded Y₂BaCuO₅ (211) particles do not show any preferred texture, but their presence within the 123-matrix alters the growth of the 123-phase, independent of the orientation. EBSD enables to analyse the interactions between the 123- and 211-phases in detail.     

A novel dynamic survivable routing in WDM optical networks with/without sparse wavelength conversion

In this paper, we study the dynamic survivable routing problem, both in optical networks without wavelength conversion and in optical networks with sparse wavelength conversion, and propose a novel hybrid algorithm for it based on the combination of mobile agents technique and genetic algorithms (GA). By keeping a suitable number of mobile agents in the network to cooperatively explore the network states and continuously report cycles (that are formed by two disjoint-link routes) into the routing tables, our new hybrid algorithm can promptly determine the first population of cycles for a new request based on the routing table of its source node, without the time consuming process associated with current GA-based lightpath protection schemes. We further improve the performance of our algorithm by introducing a more advanced fitness function that is suitable for both the above networks. Extensive simulation studies on the ns-2 network simulator show that our hybrid algorithm achieves a significantly lower blocking probability than the conventional survivable routing algorithms for all the cases we studied.     

Correlations Among Maximum Likelihood and Weighted/Unweighted Least Squares Estimators in Factor Analysis

The asymptotic correlations among maximum likelihood (ML) and various least squares (LS) estimators in factor analysis are derived. The LS estimators include the unweighted (ULS) and weighted estimators for unstandardized variables and the ULS estimators for standardized variables. The derived formulas cover the cases with restrictions on parameters. Numerical examples with simulations are provided to confirm the accuracy of the formulas and the influence of scales on the asymptotic correlations.

     

Dyeing properties of oxygen low-temperature plasma-treated wool and nylon 6 fibres with acid and basic dyes

Wool and nylon 6 fibres treated with oxygen low-temperature plasma were dyed with acid and basic dyes. Despite the increase of electronegativity of the fibre surface caused by the plasma treatment, the rate of dyeing of wool was increased with both dyes, while that of nylon 6 was decreased with the acid dye and increased with the basic dye.     

Numerical analyses of high‐beta spherical tokamaks with varied elongation

The effect of plasma elongation on the second‐stable spherical tokamak (ST) was numerically studied using the experimentally measured pressure and current profiles of ultrahigh‐beta STs. The maximum beta of ST over 50% was obtained in the TS‐3 ST/CT experiment by applying an external toroidal field to an FRC. It was found that the marginal beta for the ballooning instability increased with the plasma elongation κ of ST. The elongated STs with κ > 2 have the magnetic shear (S)–pressure gradient (α) profiles located in the second‐stable regime for the ballooning mode and the stability margin increased with κ. The close relation between the absolute minimum‐B profile and the second stability was documented. The effect of elongation on maximum beta was observed to saturate when κ exceed 3, indicating that the optimized elongation for high‐beta STs is located around 2 < κ < 3. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(4): 1–6, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20132