β－C_2S固溶体稳定的热力学研究

从热力学理论出发，利用Ｘ射线衍射定性和定量的方法，对β－Ｃ＿２Ｓ固溶体的稳定性进行了分析和研究。经热力学理论推导得出β－Ｃ＿２Ｓ稳定的热力学条件，即掺入的微量元素的化学位μ＿ｉ须小于β－Ｃ＿２Ｓ的反应自由焓△Ｇ＿β，μ＿ｉ＜△Ｇ＿β．并定量地计算出一种微量元素稳定β－Ｃ＿２Ｓ的临界掺加量为；多种微量元素对β－Ｃ＿２Ｓ的稳定性判断条件为：     

提高E^2PROM中NMOS管源漏穿通电压的实验研究

为了提高Ｅ＾２ＰＲＯＭ中Ｎ管源漏穿通电压，用实验的方法对制造工艺进行了研究。结果表明，高能量注入是提高ＶＰＴ的有效手段，但受到ｐｎ结击穿的限制，只适用于低区短沟Ｎ管；ＤＤＤ工艺大幅度高ＶＰＴ，但ｐｎ结击穿电压低于２０Ｖ，不能应用于高压ＭＯＳ管；采用适量的防穿通注入和适当增大沟道长度为最理想的工艺途径。     

CHARAC TERIZATION OF TiAl POWDER PRODUCED BY MECHANICAL ALLOYING

The microstructure,alloying reaction and sintering behavior of the powder produced by Mechanical Al-loying(MA)for 8 h from 64 wt.-% Ti powder and 36 wt.-% Al powder were studied by scanning electronmicroscopy,optical microscopy,X-ray diffractometry,differential scanning calorimetry(DSC)and dilatometry.The mechanically alloyed powder partictes are Ti-Al composite particles.Thus,titanium aluminides can formeasily in the powder through diffusion during heat treatment.It is shown that the sintering behavior of this pow-der,different from the behaviors of TiAl alloy powder and mixed powder of 64 wt.-% Ti powder and 36 wt.-%Al powder,changes from expansion at temperatures below 1000℃ to shrinkage at temperatures above 1000℃.Homogeneously alloyed TiAl material with a density over 96% of the theoretical density can be produced fromthe mechanically alloyed powder by compaction-sintering.     

Possible Energy Network with polygeneration system and CCS for China

On basis of adopting polygeneration systems for power and alternative fuels,capturing CO2 with near zero energy penalties,and storing CO2 on sites,a new kind of Energy Network can integrate energy utilization,CO2 capture,transportation and storage synthetically.Techno-economic analysis of this solution focusing on Inner Mongolia and the Yangtze River Delta districts had been carried with comparison to the chain method for energy utilization and CO2 sequestration.This solution can save 21.5% of energy,and re...     

Analysis of junction temperatures in high-power GaN-based LEDs

We presented the analysis of the incomplete conduction in bonding medium in high power GaN-based light-emitting diode (LED) packages. A numerical study was carried out with parametric model to understand the junction temperature variation due to bonding medium defects. Transient thermal measurement was performed to evaluate LED’s junction temperature. Thermal resistance from chip to lead frame was 20 K/W in our sample LED. It was suggested that only 60% of the surface area of the bonding medium was involved...     

Preparation of micro-patterned surfaces of Si-N-O films and their influence on adhesion behavior of endothelial cells

Microgrooves were prepared on Si(100) surface by photolithography and wet etching.Subsequently,Si-N-O films were deposited on the microgrooves by unbalanced magnetron sputtering(UBMS) and micro-patterned surfaces of Si-N-O films were obtained.The size of the micropatterns was measured by surface profilometer.The chemical composition of Si-N-O films were characterized by X-ray photoelectron spectrometry(XPS) and the wettability of the micropatterned surfaces was evaluated by contact angle measurement.The beh...     

A novel shaft-less double suction mini pump

A novel double suction shaft-less mini pump was developed for heat control of small energy systems in this study.The mini pump impeller with an exit diameter of 40 mm was combined with the motor rotor supported by the hybrid dynamic bearing.The specific speed of the pump was 125 min-1 m3 min-1 m.The hydraulic performance of the pump was investigated experimen-tally under four rotational speeds.From the test results,it was recognized that the pump could provide a flow discharge of 5 L/min and head of 1.5 m,w...     

Fuel combustion test in constant volume combustion chamber with built-in adaptor

Combustion tests of pre-mixture of methane and air in constant volume combustion chamber(CVCC) have been carried out by means of flame propagation photo and gas pressure measurement,the effects of CVCC body temperature,intake pressure of pre-mixture of methane and air,equivalence ratio and location of the built-in adaptor have been investigated.The whole combustion chamber can be divided into two parts,i.e.the upper combustion chamber and the lower combustion chamber,by the built-in adaptor with through hol...     

Air-source heat pump coupled with economized vapor injection scroll compressor and ejector:Design and experimental research

Ejector can utilize high pressure energy from liquid mechanism,it can be used in heat pump system coupled with economized vapor injection(EVI)scroll compressor.When running under low temperature conditions,the performance of the EVI system with ejector can be improved further.In this paper,the design method of the heat pump system with ejector is presented,and the process for designing the heat pump with ejector(EVIe)was summarized.One prototype heat pump was designed under the condition of the evaporation ...