全文获取类型
收费全文 | 395篇 |
免费 | 55篇 |
国内免费 | 833篇 |
专业分类
电工技术 | 16篇 |
综合类 | 7篇 |
化学工业 | 57篇 |
金属工艺 | 573篇 |
机械仪表 | 7篇 |
建筑科学 | 2篇 |
矿业工程 | 2篇 |
轻工业 | 12篇 |
水利工程 | 3篇 |
石油天然气 | 6篇 |
无线电 | 207篇 |
一般工业技术 | 113篇 |
冶金工业 | 11篇 |
原子能技术 | 197篇 |
自动化技术 | 70篇 |
出版年
2014年 | 1篇 |
2009年 | 1篇 |
2004年 | 2篇 |
2003年 | 1篇 |
2002年 | 1篇 |
2001年 | 3篇 |
2000年 | 7篇 |
1999年 | 6篇 |
1998年 | 9篇 |
1997年 | 17篇 |
1996年 | 12篇 |
1995年 | 5篇 |
1994年 | 9篇 |
1993年 | 184篇 |
1992年 | 124篇 |
1991年 | 128篇 |
1990年 | 218篇 |
1989年 | 152篇 |
1988年 | 112篇 |
1987年 | 30篇 |
1986年 | 30篇 |
1985年 | 38篇 |
1984年 | 22篇 |
1983年 | 17篇 |
1982年 | 8篇 |
1981年 | 2篇 |
1980年 | 24篇 |
1979年 | 19篇 |
1966年 | 2篇 |
1965年 | 22篇 |
1963年 | 9篇 |
1960年 | 3篇 |
1959年 | 15篇 |
1958年 | 8篇 |
1957年 | 24篇 |
1956年 | 18篇 |
排序方式: 共有1283条查询结果,搜索用时 15 毫秒
1.
利用化学镀方法制备了非晶态Fe-Sn-B合金镀层,研究了镀液浓度对镀宙积速度,成分,表面形貌,非晶态结构形成区域和耐蚀性的影响,得出了最佳镀液浓度及施镀条件。 相似文献
2.
3.
对 32 P的切仑科夫计数法及液闪测量作了比较 ,同时对于不同样品瓶和闪烁液对 32 P计数效率的影响进行了实验比较 ,指出提高 32 P测量效率的途径 相似文献
4.
5.
6.
本文介绍 OEIC 器件,侧重于基于 GaAs 和 InP 材料的、应用于光纤通信的 OEIC 发射器、接收器和中继器的发展现状、器件性能和各种关键新工艺,并探讨了其发展动向。 相似文献
7.
8.
To bring the excellent abrasion-resistant po-tential of carbide into full play,composites of casttungsten carbide(CTC)grains based on mainlyplate martensite and high Cr,W white cast iron aremade on substrate of grey iron by cast-in-placehardfacing process.Results of high-stresstwo-body and three-body abrasion show that:(1)Base alloy microstructures have overwhelmingdominating effects on abrasion resistances of thecomposites in two-body and especially three-bodyabrasion systems.(2)All composites have very ex-cellent abrasion-resistances which increase drasti-cally with the increase of CTC grain size.In case ofthe same CTC grain size,composite based onmartensite white cast iron is much morewear-resistant than that based on mainly platemartensite although the volume fraction of CTCgrains in the latter is considerably larger than thatin the former.In three-body abrasion system,loadhas little effect on wear rate for composites basedon martensite white cast iron,but wear rate ofconventional wear-resistant materials increaseslinearly in a very steep slope as the nominal stressincreases. 相似文献
9.
The effect of compressive deformation testedabove the M_s temperature on the martensitemorphology in Fe-Ni-C alloys has been studied.Inthe Fe-30Ni-0.12C alloy,the M_s temperature is-50℃ The cylindrical specimens werecompressively deformed at -40℃.The strain rateswere 10,20,30 and 40%.X-ray analysis andmetallographic examination showed that nostrain-induced martensite was found.After quench-ing to -53℃,some thin plates and unusualmorphologies of lenticular martensites with bentand/or broken mid-ribs were observed.In theFe-30Ni-0.34C alloy,the M_s temperature is-120℃.Compressive deformation with differentstrain rates were carried out at room temperature.After quenching to the liquid nitrogen temperature,some bent thin plate matensites(unbroken)occur-red.The transformed twins in bent plate were alsobent and nearly parallel to the γ-α'interfaces.Orientation relationship between austenite and bentmartensite has been examined by means of trans-mission electron microscope.It was proved thatthese unusual morphologies are inherent in thecompressive pre-deformed austenite. 相似文献
10.
在双轴加载条件下对Ⅰ型疲劳裂纹扩展进行了研究。载荷范围从0.08σ_s到0.71σ_3,包括比例加载和非比例加载。基于对Von Mises理论的讨论,提出一个新的力学参数。双轴加载条件下的弹塑性参数P成功地描述了双轴比例加载和非比例加载下的疲劳裂纹扩展。 相似文献