The Effect of Drying Temperature on Physical Properties of Thin Gelatin Films

The molecular morphology of thin gelatin films, controlled through the casting temperature, was monitored by wide angle X-ray diffraction (WAXD) and differential scanning calorimetry (DSC). Gelatin films dried at lower temperatures had a markedly higher crystalline or helical structure with a slightly higher T_g and lower ΔC_p compared with hot dried films, which had a more coiled structure. The relationship between molecular morphology and gelatin-water interaction in terms of hydration behavior and water diffusivity was assessed using dynamic vapor sorption (DVS). The sorption capacity increased and the level of hysteresis decreased with increasing the degree of crystallinity. The difference in the aging behavior of the films was explained in terms of the difference between the glass transition and aging temperatures, (Tg – Ta).     

An online optimum voltage estimation and real‐time MPP tracking for a PV system

In this paper, a photovoltaic system topology incorporating a new maximum power point tracking (MPPT) controller method is presented. This method uses an autotuning estimator and a PI controller to make the system work in the maximum power point. The controller is formulated based on the bijectivity in the photovoltaic generator characteristic; therefore, if the optimal voltage is reached, this means that the maximum of power is obtained. The proposed MPPT algorithm is implemented on a dSpace DS1104 controller board. In order to demonstrate the efficiency of the proposed algorithm in real time, an experimental setup using a boost converter connected to a resistive load is successfully implemented and studied. The obtained experimental results prove the validity of the proposed MPPT algorithm.     

Effect of extraction methods on kinetic,chemical composition and antibacterial activities of Tunisian Thymus vulgaris. L. essential oil

The present study aims to compare two innovative extraction techniques: microwave-assisted hydrodistillation (MAHD) and solvent-free microwave extraction (SFME) through traditional extraction techniques: hydrodistillation (HD) and steam distillation (SD) for their efficiency in the extraction of the volatile compounds from Tunisian Thymus vulgaris leaves; the kinetic, yield, composition and antibacterial activities of the essential oil were assessed in vitro. Results show that the essential oils extracted by microwaves were quantitatively (yield) similar to those obtained through the conventional methods, but qualitatively, essential oils analysed by gas chromatography–mass spectrometry (GC–MS) presented 17, 11, 11 and 8 compounds obtained through SFME, MAHD, SD and HD, respectively, mostly consisting of carvacrol (89.24–41.17%), followed by γ-terpinene (11.37–1.37%) and para-cymene (27.95–2.05%). The essential oils were screened for antibacterial activity against 5 microorganisms. All essential oils obtained by studied extraction methods showed the same resistance against Gram (?) and Gram (+) bacteria. The SFME method gave the best results: rapid kinetic of extraction (30 min vs. 35 min for MAHD, 120 min for SD, and 180 min for HD), less energy saving and cleanest process.     

A hybrid discontinuous in space and time Galerkin method for wave propagation problems

Medium‐frequency regime and multi‐scale wave propagation problems have been a subject of active research in computational acoustics recently. New techniques have attempted to overcome the limitations of existing discretization methods that tend to suffer from dispersion. One such technique, the discontinuous enrichment method, incorporates features of the governing partial differential equation in the approximation, in particular, the solutions of the homogeneous form of the equation. Here, based on this concept and by extension of a conventional space–time finite element method, a hybrid discontinuous Galerkin method (DGM) for the numerical solution of transient problems governed by the wave equation in two and three spatial dimensions is described. The discontinuous formulation in both space and time enables the use of solutions to the homogeneous wave equation in the approximation. In this contribution, within each finite element, the solutions in the form of polynomial waves are employed. The continuity of these polynomial waves is weakly enforced through suitably chosen Lagrange multipliers. Results for two‐dimensional and three‐dimensional problems, in both low‐frequency and medium‐frequency regimes, show that the proposed DGM outperforms the conventional space–time finite element method. Copyright © 2014 John Wiley & Sons, Ltd.     

The processing element design for a large-scale spatio-temporal pattern clustering system

The clustering of spatio-temporal patterns are essential for many applications. Established from the biological analogy of the cortex, the parametrically coupled logistic map network (PCLMN) provides a viable solution to the clustering problem. To engineer for a single-chip spatio-temporal pattern clustering system, the highly modular PCLMN is designed in analog circuit. In this paper, the 0.6 μm 5 V CMOS design of the processing element is presented. The analog design employs self-calibration techniques to improve the accuracy and robustness of the nonlinear circuits. A fabricated element covers a die area of 0.55 mm², and consumes 240 mW power at 5 V supply. After calibration, simulation and testing results show that the element fulfills the system-level requirement of the Cort-X model for driving signals up to 1 MHz.     

CHANGES IN ASPHALT CHEMISTRY AND DURABILITY DURING OXIDATION AND POLYMER MODIFICATION

The Gulf Countries' environmental conditions are very severe. The temperature zoning study indicate that more than half of Gulf areas experience a maximum seven consecutive days pavement temperature of 76°C (Al-Abdul Wahhab et al., 1997). This has resulted in damage to the road networks in the form of cracking, rutting and deformation. Polymer modification of asphalt is required to increase the resistance to permanent deformation at relatively high temperatures without adversely affecting the properties of the asphalts at low temperature. In this work chemical and performance-related properties of fresh, oxidized, and polymer modified asphalts were evaluated. The physical properties and performance characteristics of asphalts were found to depend on the chemical composition of asphalt. The interactions of polar functionalities actually present or formed during oxidative aging or due to polymer modification, influence the viscosity and related flow properties. The changes in composition of fresh, oxidized and polymer-modified asphalts can be clearly identified from Infrared spectroscopy. NMR spectroscopy enables detailed information about the Carbon-and-hydrogen-types and average molecular/structural parameters of asphalt without separating it into different components.     

Chemical desulfurization of petroleum fractions for ultra-low sulfur fuels

An improved desulfurization process for removing sulfur from hydro treated diesel oil based on the oxidation of thiophenic type sulfur-containing compounds with H₂O₂ and acetic acid (AcOH) using H₂SO₄ as catalyst has been studied. The experimental results show that the sulfone content in the oxidation product increased rapidly with an increase in acetic acid and sulfuric acid ratios from 1:0 to 2:1 mole ratios. The maximum DBT conversion (wt.%) was at 2:1 mole ratio of acetic acid/sulfuric acid. This oxidation process is found to be capable of removing up to 90% of the sulfur compounds in hydro treated real fuels and can provide an alternative way to meet the future sulfur environmental requirements.     

Fabrication of low friction bronze–graphite nano-composite coatings

This paper addresses the fabrication of bronze–nano-graphite coatings containing 30 nm sized graphite particles. Addition of Poly Vinyl Pyrrolidone (PVP) and dispersing the suspension by ultrasound was utilized to stabilize the electroplating solution. Pulsed current electrodeposition was used and the deposits were characterized in terms of graphite content, particle dispersion in coating and morphology. The wear behavior of the coating was compared to bronze–micro-graphite coatings prepared with the same experimental conditions. The present coating showed improved wear resistance in comparison to bronze–micro-graphite coatings at the same graphite content.     

DRYING KINETICS AND CHARACTERISTIC DRYING CURVE OF LIGHTLY SALTED SARDINE (SARDINELLA AURITA)

Drying of lightly salted sardine (Sardinella aurita) was accomplished using three air temperatures (35°C, 40°C, 50°C) and three air velocities (0.5 m/s, 1.5 m/s, 2 m/s); the effects of drying conditions on drying kinetics were studied. As for all biological products, air temperature is the main factor influencing the drying kinetics. However, over a given temperature which seems to correspond to protein modification (50°C), and at a high air flow rate (2 m/s and 2.5 m/s) a crust formation on the surface of the fish, due to the combined effect of heat and salt was observed. This phenomenon inhibited the drying rate. From the drying curves, two falling rate periods were observed. The dimensionless drying rate versus a dimensionless moisture content data were regressed by the Marquardt Levenberg non-linear optimization method to obtain an empirical equation describing the salted sardine characteristic drying curve.