Application results of a prototype ultrasonic liquid film sensor to a 7 MPa steam–water two-phase flow experiment

A prototype ultrasonic liquid film sensor was applied to a high-temperature steam–water two-phase flow experiment. The liquid film sensor was vertically installed in a loop which was connected to HUSTLE, a multi-purpose steam source test facility. The hydraulic diameter of the measurement section was 9.4 mm. The output waveforms of the sensor were acquired with a digital oscilloscope. The fluid temperature and system pressure were kept at 288 °C and 7.2 MPa, respectively, during the experiment. The pulse-echo method was used to calculate the liquid film thickness. The cross-correlation calculation was utilized to determine the time difference between the pulse reflected at the sensor surface and the pulse reflected at the liquid film surface. The time-averaged liquid film thicknesses were less than 0.055 mm in the annular flow condition. The increase of the time-averaged thickness was small with the change of the gas momentum flux. The film thicknesses measured with the sensor were compared with the past experimental results; the former were smaller than one-fourth of the thickness estimated as the mean film thickness. The comparison results suggested that the continuous liquid sublayer thickness was measured with the liquid film sensor.     

Crystallography and Interphase Boundary of Martensite and Bainite in Steels

Grain refinements in lath martensite and bainite structures are crucial for strengthening and toughening of high-strength structural steels. Clearly, crystallography of transformation plays an important role in determining the “grain” sizes in these structures. In the present study, crystallography and intrinsic boundary structure of martensite and bainite are described. Furthermore, various extrinsic factors affecting variant selection and growth kinetics, such as elastic/plastic strain and alloying effects on interphase boundary migration, are discussed.     

Grain Refinement by Cyclic Displacive Forward/Reverse Transformation in Fe-High-Ni Alloys

A novel method for grain refinement of martensite structures was proposed, in which transformation strain is accumulated by cyclic displacive forward and reverse transformations. This method can refine martensite structures in an Fe-18Ni alloy because a high density of austenite dislocations is introduced by a displacive reverse transformation in addition to an inheritance of dislocations in body-centered cubic martensite into austenite during cyclic transformation. The addition of a small amount of carbon accelerates structure refinement significantly, which results in the formation of ultra-fine-grained structures after ten cycles.

     

Control of assembly size of poly (methacrylic acid)-<Emphasis Type="Italic">grafted</Emphasis> fullerenes in aqueous solution

We synthesized poly(methacrylic acid)-grafted fullerenes (PMA-C₆₀) with different PMA molecular weights and investigated the assembly size formed by PMA-C₆₀ in aqueous solution. The molecular weight of PMA strongly affects the assembly size: PMA-C₆₀ with a larger molecular weight forms micelles with 20 nm diameters while PMA-C₆₀ with a smaller molecular weight forms monodisperse assemblies with 200 nm hydrodynamic diameters. We succeeded in converting the large monodisperse assembly into micelles by adding either ionic species or ethanol. This result provides insight into controlling the assembly size of fullerene-containing assemblies.     

Study of polarization phenomena in Schottky CdTe diodes using infrared light illumination

Schottky CdTe diode detectors suffer from a polarization phenomenon, which is characterized by degradation of the spectral properties over time following exposure to high bias voltage. This is considered attributable to charge accumulation at deep acceptor levels. A Schottky CdTe diode was illuminated with an infrared light for a certain period during a bias operation, and two opposite behaviors emerged. The detector showed a recovery when illuminated after the bias-induced polarization had completely progressed. Conversely, when the detector was illuminated before the emergence of bias-induced polarization, the degradation of the spectral properties was accelerated. Interpretation of these effects and discussion on the energy level of deep acceptors are presented.     

Analysis of a change in bacterial community in different environments with addition of chitin or chitosan

The temporal changes of a bacterial community in soil with chitin or chitosan added were analyzed by PCR-denaturing gradient gel electrophoresis (DGGE) targeting the 16S rRNA gene using total DNAs prepared from the community. Band patterns of PCR-DGGE confirmed that 31 species become predominant after the addition of chitin or chitosan. The determination of the nucleotide sequences of the bands of the 31 species indicated that 20 species belonged to the division Proteobacteria, and that the genus Cellvibrio was apparently predominant among them (7/20). The 16S rRNA sequences of the 16 deduced species (16/31) showed less than 98% similarities to those of previously identified bacteria, indicating that the species were derived from unidentified bacteria. The total community DNAs extracted from bacterial cells adsorbed on the surface of flakes of chitin and chitosan placed in a river, a moat, or soil were subjected to PCR-DGGE to examine the extent of diversity of chitinolytic bacteria among different environments. The predominant species significantly differed between the chitin and chitosan placed in the river and moat, but not so much between those placed in the soil. The large difference between the diversities of the three bacterial communities indicated that a wide variety of bacteria including unidentified ones are involved in the degradation of chitin and chitosan in the above-mentioned natural environments.     

Estimating Land Use Impacts on Regional Scale Urban Water Balance and Groundwater Recharge

Anthropogenic activities have exerted increasingly large-scale influences on terrestrial ecological systems from the past century, primarily through agriculture; however, the impact of such changes on the hydrologic cycle is poorly understood. As one of the important land use (LU) in the coastal Dogo Plain of the Seto Inland Sea, Japan, paddy fields have been decreasing with the increase in urbanization in recent decades. As the main source of water in the Dogo Plain, groundwater plays an important role in providing people with fresh water and contributing to stream base flow. The purpose of this study is to analyze the water resource and evaluate the effect of LU change on groundwater table fluctuation in this coastal plain. Firstly, the observations of groundwater table and the investigation of water balance were carried out in this alluvial plain. Then, a distributed four-block three-layer water balance model was employed to analyze the groundwater table fluctuation with response to the change of paddy field area. Moreover, the role of paddy field in recharging groundwater in the basin has been clarified. Results show that groundwater table depends not only on rainfall and discharge from rivers, but also on irrigation water and topology of the study area. The net groundwater recharge was positive in irrigation periods whereas that in non-irrigation periods was nearly equal to zero or negative. The results of this study would be helpful to the urban development policy and land use planning decision.     

When NHC Ligands Make a Difference in Gold Catalysis

Thanks to their unique electronic and steric properties, carbene ligands offer highly valuable features for catalysis, including homogenous gold catalysis. The use of carbene-gold complexes has improved existing reactions, either by modifying reactivity modes or by leading to highly asymmetric processes. These topics will be discussed on the basis of selected examples.     

Numerical simulation on the behavior of a liquid jet into an air flow

A numerical simulation has been performed to clarify the effects of turbulence in a liquid on the deformation of the liquid jet surface into an air flow. The turbulences in the liquid jet were simulated by the Rankin vortices, and the liquid jet surface was tracked numerically by the volume of fluid method. By numerical simulations, the onset of the protrusions on the liquid jet surface is caused by the vortices in the liquid, and the surrounding air flow plays an important role in the amplification of the protrusions. The amplification rate of the trough displacement is proportional to the air‐to‐liquid velocity ratio. At large imposed vortex intensities, the trough displacement increases with the vortex intensity. On the other hand, at small imposed vortex intensities, the amplification of the trough displacement is also affected by factors other than vortex intensity. © 2001 Scripta Technica, Heat Trans Asian Res, 30(6): 473–484, 2001     

Effects of Pre-tempering on Intercritical Annealing in Fe-2Mn-0.3C Alloy

As-quenched martensite was pre-tempered at 623 K and 923 K (350 °C and 650 °C), and then it reverted to austenite by intercritical annealing at 998 K (725 °C) in a Fe-2Mn-0.3C alloy. Pre-tempering at 623 K (350 °C) accelerates austenite formation, while pre-tempering at 923 K (650 °C) significantly retards it. It is proposed that austenite nucleation is accelerated by increasing the number density and particle size of cementite during tempering, whereas austenite growth is retarded by Mn enrichment in cementite during tempering at high temperature, leading to opposite effects of pre-tempering on reversion kinetics.