A benzoate coprecipitation route for synthesizing nanocrystalline GDC powder with lowered sintering temperature

Electrolyte powders with low sintering temperature and high-ionic conductivity can considerably facilitate the fabrication and performance of solid oxide fuel cells (SOFCs). Gadolinia-doped ceria (GDC) is a promising electrolyte for developing intermediate- and low-temperature (IT and LT) SOFCs. However, the conventional sintering temperature for GDC is usually above 1200 °C unless additives are used. In this work, a nanocrystalline powder of GDC, (10 mol% Gd dopant, Gd_0.1Ce_0.9O_1.95) with low-sintering temperature has been synthesized using ammonium benzoate as a novel, environmentally friendly and cost-effective precursor/precipitant. The synthesized benzoate powders (termed washed- and non-washed samples) were calcined at a relatively low temperature of 500 °C for 6 h. Physicochemical characteristics were determined using thermal analysis (TG/DTA), Raman spectroscopy, FT-IR, SEM/EDX, XRD, nitrogen absorptiometry, and dilatometry. Dilatometry showed that the newly synthesized GDC samples (washed and non-washed routes) start to shrink at temperatures of 500 and 600 °C (respectively), reaching their maximum sintering rate at 650 and 750 °C. Sintering of pelletized electrolyte substrates at the sintering onset temperature for commercial GDC powder (950 °C) for 6 h, showed densification of washed- and non-washed samples, obtaining 97.48 and 98.43% respectively, relative to theoretical density. The electrochemical impedance spectroscopy (EIS) analysis for the electrolyte pellets sintered at 950 °C showed a total electrical conductivity of 3.83 × 10^?2 and 5.90 × 10^?2 S cm^?1 (under air atmosphere at 750 °C) for washed- and non-washed samples, respectively. This is the first report of a GDC synthesis, where a considerable improvement in sinterability and electrical conductivity of the product GDC is observed at 950 °C without additives addition.     

Acoustic damping flexible polyurethane foams: Effect of isocyanate index and water content on the soundproofing

High-efficiency sound absorbing flexible polyurethane foams (FPUFs) are manufactured using nonpolar polyester resin, methylene diphenyl diisocyanate, and other reagents by one-shot bulk polymerization. In this study, the impact of the isocyanate index (90, 100, and 110) and water content (2.5 and 5%) on the microphase separation and soundproofing behavior of FPUFs are examined using atomic force microscopy, Fourier transform infrared spectroscopy, optical microscope, and an impedance tube device. The results reveal that the increase of the isocyanate index and water content leads to the increase of the cell size, cell size distribution, open-cell content, cell wall roughness, and microphase separation. Also, maximum sound absorption coefficient (α) reaches to 0.98 and the average of α in the frequency range of 1500–4000 Hz increases from 0.7 to 0.87 by increasing the water content from 2.5 to 5% and isocyanate index from 90 to 110; therefore, acoustic damping performance enhances up to 26.24% due to the synergic effects of microphase separation on the viscose media formation, open-cell content, cell wall roughness, cell size, and cell size distribution. In conclusion, FPUFs with an optimal amount of microphase separation and drainage flow can be a promising candidate for sound insulating materials. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47363.     

Thermal-Disrupting Interface Mitigates Intercellular Cohesion Loss for Accurate Topical Antibacterial Therapy

Bacterial infections remain a leading threat to global health because of the misuse of antibiotics and the rise in drug-resistant pathogens. Although several strategies such as photothermal therapy and magneto-thermal therapy can suppress bacterial infections, excessive heat often damages host cells and lengthens the healing time. Here, a localized thermal managing strategy, thermal-disrupting interface induced mitigation (TRIM), is reported, to minimize intercellular cohesion loss for accurate antibacterial therapy. The TRIM dressing film is composed of alternative microscale arrangement of heat-responsive hydrogel regions and mechanical support regions, which enables the surface microtopography to have a significant effect on disrupting bacterial colonization upon infrared irradiation. The regulation of the interfacial contact to the attached skin confines the produced heat and minimizes the risk of skin damage during thermoablation. Quantitative mechanobiology studies demonstrate the TRIM dressing film with a critical dimension for surface features plays a critical role in maintaining intercellular cohesion of the epidermis during photothermal therapy. Finally, endowing wound dressing with the TRIM effect via in vivo studies in S. aureus infected mice demonstrates a promising strategy for mitigating the side effects of photothermal therapy against a wide spectrum of bacterial infections, promoting future biointerface design for antibacterial therapy.     

Effect of baking in different ovens on the quality and structural characteristics of saltine crackers

The aim of the study was to evaluate the physical and microstructural characteristics of crackers baked in four different industrial baking ovens (indirect radiation-cyclotherm, indirect convection, hybrid and industrial tunnel-ITO). Indirect convection and cyclotherm ovens provide the highest (5685.43 ± 51 W m⁻²) and the lowest (4860 ± 38.87 W m⁻²) amount of heat flux, respectively. Despite the amount of heat flux, indirect convection led to crackers with the highest moisture (7.86% vs. 4.82% in clyclotherm) and specific volume, but the lowest hardness. Cyclotherm resulted in crackers with lower specific volume, surface area, porosity, smooth and regular surface. Conversely, the hybrid and ITO ovens showed closer heat flux, leading to crackers with similar moisture content, texture parameters, specific volume, browning and inner porosity. Overall results show the potential of baking using different ovens for modifying the quality parameters of the crackers.     

Effect of Shot Peening Operation on the Microstructure and Wear Behavior of AZ31 Magnesium Alloy

Protection of Metals and Physical Chemistry of Surfaces - Shot peening is a treatment used to increase surface hardness and wear resistance. In this study, the effect of shot peening on the...     

Two-level distributed clustering routing algorithm based on unequal clusters for large-scale Internet of Things networks

The Journal of Supercomputing - According to the recent advancements in communication technologies and the widespread use of smart devices, our environment can be transforming into the Internet of...     

Engineering geological properties of the pyroclastic cone-shaped rocky houses of Kandovan,Iran

Bulletin of Engineering Geology and the Environment - Kandovan is one of the geo-tourism attractions in the East Azarbaijan Province of Iran, where rural houses were carved within the cone-shaped...     

Stability enhancement of polypyrrole thin film ammonia sensor by camphor sulfonic acid dopant

Journal of Materials Science: Materials in Electronics - The main weakness of polymer gas sensors is its stability. Here, we report stability enhancement of a 100 nm polypyrrole (PPy) thin...     

Feasibility of Treatment of Refinery Wastewater by a Pilot Scale MF/UF and UF/RO System for Reuse at Boilers and Cooling Towers

A pilot-scale hybrid membrane system, consisting of a ceramic microfilter (MF), two differentpolyvinyl chloride (PVC) and polyacrylonitrile (PAN) ultrafilters (UF), and a polyamide reverse osmosis (RO) filter, has been utilized to decrease harmful and damaging components in wastewater produced from Tehran Refinery with aim to be reused at boilers and cooling towers. Taguchi method was employed to find optimum operating conditions including transmembrane pressure, cross flow velocity (CFV), temperature, and backwash time. Further, analysis of variance (ANOVA) was performed to determine the significance of controlling factors on total organic carbon rejection and normalized permeate flux. MF (ceramic)/UF (PVC) system reduced, %: oil 99.7; chemical oxygen demand (COD) 82; biochemical oxygen demand (BOD) 79.3; conductivity 60.5; total dissolved solids (TDS) 52.6; turbidity 99.7 and total hardness 73.2. MF(ceramic)/UF (PAN) system reduced: oil, COD, BOD, conductivity, TDS, turbidity, and total hardness by 99.8; 84.2; 80.8; 62.72; 55; 99.9 and 78.4%, respectively. UF (PAN)/RO system decreased, %: oil 99.5; COD 99; BOD 99; conductivity 98; TDS 98; turbidity 98.7 and total hardness 99.94. Obtained treated wastewater by this system can be reused as feed water of boilers.