Toward a better understanding of multifunctional cement-based materials: The impact of graphite nanoplatelets (GNPs)

The impact of graphite nanoplatelets (GNPs) on the physical and mechanical properties of cementitious nanocomposites was investigated. A market-available premixed mortar was modified with 0.01% by weight of cement of commercial GNPs characterized by two distinctively different aspect ratios.The rheological behavior of the GNP-modified fresh admixtures was thoroughly evaluated. Hardened cementitious nanocomposites were investigated in terms of density, microstructure (Scanning Electron Microscopy, SEM and micro–Computed Tomography, μ-CT), mechanical properties (three-point bending and compression tests), and physical properties (electrochemical impedance spectroscopy, EIS and thermal conductivity measurements). At 28 days, all GNP-modified mortars showed about 12% increased density. Mortars reinforced with high aspect ratio GNPs exhibited the highest compressive and flexural strength: about 14% and 4% improvements compared to control sample, respectively. Conversely, low aspect ratio GNPs led to cementitious nanocomposites characterized by 36% decreased electrical resistivity combined with 60% increased thermal conductivity with respect to the control sample.     

Regenerable Sorbents for High-Temperature Desulfurization of Syngas from Biomass Gasification

Single-metal high-temperature solid sorbents for syngas cleaning using Mn, Ca, Fe, Cu, or Mo supported on γ-Al₂O₃ were synthesized, characterized, and tested in a fixed-bed reactor. H₂S and SO₂ concentrations in the gas after treatment at T = 400 to 700 °C were compared with thermodynamic calculations. The Mn-based sorbent showed the best ability to achieve a low sulfur residual in the gas, especially at temperatures above 600 °C. Sorbents with Fe, Cu, and Mo gave SO₂ formation in the initial phase, but this could be avoided by a pre-reduction treatment of the sorbent material.     

辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响

研究辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响。采用3种不同上辊/下辊转速比(ω/ω0,ω为上辊转速,ω0为下辊转速)1:1、1:1.2及1:1.4进行多次试验。结果显示,在最大辊速差条件下(ω/ω0=1:1.4),7075铝板在轧制方向的屈服强度和极限抗拉强度分别提高41.5%和21.9%。此外,当辊速比ω/ω0为1:1.4时,成品轧制板的平均晶粒尺寸减小36%,横剖面平均硬度增加约9.2%。织构研究结果显示,辊速差越大,成品各向同性及硬度越大。然而,采用不同辊速度的连铸连轧会导致变形板伸长率降低约6%。     

Co-precipitation synthesis of CeVO4 nanoparticles for electrochemical hydrogen storage

Journal of Materials Science: Materials in Electronics - In this study, cerium vanadate (CeVO4) nanoparticles were synthesized using ammonium metavanadate and cerium (III) nitrate hexahydrate as...     

Evaluation of the localized corrosion on Mg electrode surface by electrochemical noise technique

The symmetrical and asymmetrical electrodes made of Mg were studied in 0.1-M NaCl electrolyte adjusted at pH 12. The statistical and wavelet methods were employed for analyzing the electrochemical current noise (ECN) signals. The asymmetric configuration was used for electrochemical detection of filiform corrosion on Mg electrode. The real time scale of the dominant transients of the asymmetric electrodes was detected on the basis of the maximum peak in the SDPS plots. The SDPS values of the real time scale crystals of the ECN signals resulting from asymmetrical electrodes increased with the increase in immersion time due to the onset of filiform corrosion.     

LBM investigation of a Cu-water nanofluid over various configurations of pipes in the mixed convection flow

Increasing the heat capacity of heat exchangers is a crucial need for modern devices. The thermal conductivity of the usual fluids and the Nusselt (Nu) number of flows containing such fluids are two bottlenecks in the way of increasing heat delivery in the heat exchangers. For this reason, nanofluids have been introduced. The effect of utilizing a Cu-water nanofluid as a coolant of two hot pipes in a square cavity is investigated numerically with a two-component lattice Boltzmann method. The volume fraction of nanoparticles is assumed to be constant (0.03) while the Richardson (Ri) number varies from 0.02 to 20. Results show that the effectiveness of nanoparticles is better observed in the natural convection mode. However, sedimentation is also very probable at high Ri numbers, which significantly reduces the effectiveness of the nanoparticles. Configurations which produce a natural convection stream similar to the forced convection one as well as the configurations with high spacing and hence, low heat stream interactions, are the best choices for a uniform heat rate from the pipes.     

Effect of baking in different ovens on the quality and structural characteristics of saltine crackers

The aim of the study was to evaluate the physical and microstructural characteristics of crackers baked in four different industrial baking ovens (indirect radiation-cyclotherm, indirect convection, hybrid and industrial tunnel-ITO). Indirect convection and cyclotherm ovens provide the highest (5685.43 ± 51 W m⁻²) and the lowest (4860 ± 38.87 W m⁻²) amount of heat flux, respectively. Despite the amount of heat flux, indirect convection led to crackers with the highest moisture (7.86% vs. 4.82% in clyclotherm) and specific volume, but the lowest hardness. Cyclotherm resulted in crackers with lower specific volume, surface area, porosity, smooth and regular surface. Conversely, the hybrid and ITO ovens showed closer heat flux, leading to crackers with similar moisture content, texture parameters, specific volume, browning and inner porosity. Overall results show the potential of baking using different ovens for modifying the quality parameters of the crackers.     

Oxidative Aromatization of 1,3,5-trisubstituted 2-pyrazolines Using Oxalic Acid/Sodium Nitrite System

Oxidative aromatization of 1,3,5-trisubstituted 2-pyrazolines by in-situ generation of NO⁺ from oxalic acid/sodium nitrite system has been described. The main advantages of this procedure are the use of an inexpensive and readily available catalyst, facile work-up, and improved yields in aqueous ethanol.     

Fault isolation in manufacturing systems based on learning algorithm and fuzzy rule selection

Neural Computing and Applications - This paper addresses the fault detection and isolation problem in manufacturing systems. Some of these systems can be affected by several faults, a first way of...     

On the numerical solution of Fredholm integral equations utilizing the local radial basis function method

The current investigation describes a computational technique to solve one- and two-dimensional Fredholm integral equations of the second kind. The method estimates the solution using the discrete collocation method by combining locally supported radial basis functions (RBFs) constructed on a small set of nodes instead of all points over the analysed domain. In this work, we employ the Gauss–Legendre integration rule on the influence domains of shape functions to approximate the local integrals appearing in the method. In comparison with the globally supported RBFs for solving integral equations, the proposed method is stable and uses much less computer memory. The scheme does not require any cell structures, so it is meshless. We also obtain the error analysis of the proposed method and demonstrate that the convergence rate of the approach is high. Illustrative examples clearly show the reliability and efficiency of the new method.