Targeted Delivery of Anesthetic Agents to Bone Tissues using Conductive Microneedles Enhanced Iontophoresis for Painless Dental Anesthesia

Pain management during dental procedures is a cornerstone for successful daily practice. In current practice, the traditional needle and syringe injection is used to administer local anesthesia. However, the appearance of long needles and the pain associated with it often leads to dental anxiety deterring timely interventions. Microneedles (MNs) have emerged as a minimally invasive alternative to hypodermic needles and shown to be effective in transdermal drug delivery applications. In this article, the potential use of MNs for local anesthesia delivery in dentistry is explored. The development of a novel conductive MN array that can be used in combination with iontophoresis technique to achieve drug penetration through the oral mucosa and the underlying bone tissue is presented. The conductive MN array plays a dual-role, creating micro-conduits and lowering the resistance of the oral mucosa. The reduced tissue resistance further enhances the application of a low-voltage current that is able to direct and accelerate the drug molecules to target the sensory nerves supplying teeth. The successful delivery of lidocaine using this new strategy in a clinically relevant rabbit incisor model is shown to be as effective as the current gold standard.     

Preparation and characterization study on maleic acid cross-linked poly(vinyl alcohol)/chitin/nanocellulose composites

In the quest on improving composite formulations for environmental sustainability, maleic acid (MA) cross-linked poly(vinyl alcohol) (PVA)-α-chitin composites reinforced by oil palm empty fruit bunch fibers (OPEFB)-derived nanocellulose crystals (NCC) had been successfully prepared. Based on the Fourier transform infrared (FTIR) spectroscopic analysis, it was proven that molecular interactions of the cross-linker to the polymeric networks was through conjugated ester linkage. Differential scanning calorimetry (DSC) showed that the influence of MA was minimal toward crystallization in the PVA/chitin/NCC composite. Maximum tensile strength, elongation at break and Young's modulus of the respective PVA/chitin/NCC composites were achieved at different content of MA, dependent on the PVA/chitin mass ratio. Among all compositions, a maximum Young's modulus was achieved at 30 wt% MA loading in PVA/chitin-30/NCC, amounting to 2,413.81 ± 167.36 MPa. Moreover, the mechanical properties and selected physicochemical properties (swelling, gel content, and contact angle) of the PVA/chitin/NCC composites could be tailored by varying the chitin content (10–30 wt%) and MA content (10–50 wt% based on total mass of composite). In brief, this chemically cross-linked PVA-based biocomposites formulated with sustainable resources exhibited tunable physicochemical and mechanical properties.     

Making reusable reaction-bonded silicon nitride crucibles for silicon casting from kerf-loss silicon waste

Silicon kerf loss during wafer slicing and the broken quartz crucibles after silicon casting are two major solid wastes from photovoltaic (PV) industry. Especially, the recycle of kerf-loss silicon has become an urgent issue because near 100 000 t of solid wastes are generated every year. One of the most meaningful recycle routes of the kerf-loss silicon is to make silicon nitride crucibles to replace the quartz crucibles. In this study, we demonstrated how this is feasible through acid leaching refining, slip casting, and nitridation. The reaction-bonded silicon nitride (RBSN) crucibles after oxidation were found pure enough for silicon ingot growth. More importantly, they could be reused after ingot growth. With the present examples, the potential of using the kerf-loss silicon for fine ceramics is prominent.     

Fabrication and Thermal Dissipation Properties of Carbon Nanofibers Derived from Electrospun Poly(Amic Acid) Carboxylate Salt Nanofibers

Polyimides (PIs) possess excellent mechanical properties, thermal stability, and chemical resistance and can be converted to carbon materials by thermal carbonization. The preparation of carbon nanomaterials by carbonizing PI‐based nanomaterials, however, has been less studied. In this work, the fabrication of PI nanofibers is investigated using electrospinning and their transformation to carbon nanofibers. Poly(amic acid) carboxylate salts (PAASs) solutions are first electrospun to form PAAS nanofibers. After the imidization and carbonization processes, PI and carbon nanofibers can then be obtained, respectively. The Raman spectra reveal that the carbon nanofibers are partially graphitized by the carbonization process. The diameters of the PI nanofibers are observed to be smaller than those of the PAAS nanofibers because of the formation of the more densely packed structures after the imidization processes; the diameters of the carbon nanofibers remain similar to those of the PI nanofibers after the carbonization process. The thermal dissipation behaviors of the PI and carbon nanofibers are also examined. The infrared images indicate that the transfer rates of thermal energy for the carbon nanofibers are higher than those for the PI nanofibers, due to the better thermal conductivity of carbon caused by the covalent sp² bonding between carbon atoms.     

Thermal-Disrupting Interface Mitigates Intercellular Cohesion Loss for Accurate Topical Antibacterial Therapy

Bacterial infections remain a leading threat to global health because of the misuse of antibiotics and the rise in drug-resistant pathogens. Although several strategies such as photothermal therapy and magneto-thermal therapy can suppress bacterial infections, excessive heat often damages host cells and lengthens the healing time. Here, a localized thermal managing strategy, thermal-disrupting interface induced mitigation (TRIM), is reported, to minimize intercellular cohesion loss for accurate antibacterial therapy. The TRIM dressing film is composed of alternative microscale arrangement of heat-responsive hydrogel regions and mechanical support regions, which enables the surface microtopography to have a significant effect on disrupting bacterial colonization upon infrared irradiation. The regulation of the interfacial contact to the attached skin confines the produced heat and minimizes the risk of skin damage during thermoablation. Quantitative mechanobiology studies demonstrate the TRIM dressing film with a critical dimension for surface features plays a critical role in maintaining intercellular cohesion of the epidermis during photothermal therapy. Finally, endowing wound dressing with the TRIM effect via in vivo studies in S. aureus infected mice demonstrates a promising strategy for mitigating the side effects of photothermal therapy against a wide spectrum of bacterial infections, promoting future biointerface design for antibacterial therapy.     

Defect Engineering in Ambipolar Layered Materials for Mode-Regulable Nociceptor

Defect engineering represents a significant approach for atomically thick 2D semiconductor material development to explore the unique material properties and functions. Doping-induced conversion of conductive polarity is particularly beneficial for optimizing the integration of layered electronics. Here, controllable doping behavior in palladium diselenide (PdSe₂) transistor is demonstrated by manipulating its adatom-vacancy groups. The underlying mechanisms, which originate from reversible adsorption/desorption of oxygen clusters near selenide vacancy defects, are investigated systematically via their dynamic charge transfer characteristics and scanning tunneling microscope analysis. The modulated doping effect allows the PdSe₂ transistor to emulate the essential characteristics of photo nociceptor on a device level, including firing signal threshold and sensitization. Interestingly, electrostatic gating, acting as a neuromodulator, can regulate the adaptive modes in nociceptor to improve its adaptability and perceptibility to handle different danger levels. An integrated artificial nociceptor array is also designed to execute unique image processing functions, which suggests a new perspective for extension of the promise of defect engineered 2D electronics in simplified sensory systems toward use in advanced humanoid robots and artificial visual sensors.     

Affixing poly(methyl methacrylate-co-acrylic acid) nanospheres with trimethoxyvinylsilane on silicon solar module to enhance its power conversion efficiency

Poly(methyl methacrylate-co-acrylic acid) [P(MMA-co-AA)] incorporated with 0–9 wt% of trimethoxyvinylsilane (TMVS) has been studied to investigate the effect of TMVS on the adhesion properties of P(MMA-co-AA) nanospheres coated on silicon substrate as well as on the power conversion efficiency (PCE) of silicon solar module coated with the polymer nanospheres. The incorporation of 7 and 9 wt% of TMVS into the copolymer has been found to render the copolymer stronger adhesion to glass substrate than the samples with lower amount of TMVS in them. The coating of the P(MMA-co-AA) nanospheres on the glass surface of solar module increases the light harvesting efficiency by serving as an anti-reflective layer. Solar module coated with an array of P(MMA-co-AA) nanospheres with 7 wt% of TMVS yielded the highest PCE enhancement of 98% under the illumination of an AM1.5 solar simulator. The natural weathering results indicate that the copolymer with 7% of TMVS was able to withstand prolonged natural weathering exposure and remained reasonably effective in PCE enhancement up to 130 days of outdoor exposure. This study demonstrates a cost-effective technique to bind [P(MMA-co-AA)] nanospheres onto the silicon surface of solar module via siloxane linkages and thus increases the PCE of the solar module effectively. The T_g of the copolymer increased linearly from 110.31 to 118.42 °C when 0–9 wt% of TMVS was added into it. Thermogravimetry results indicate that the incorporation of TMVS does not give any significant effect on the T_d of the copolymer, which occurs at about 390 °C.