Diluted chemical bath deposition of CdZnS as prospective buffer layer in CIGS solar cell

In this study, dilute chemical bath deposition technique has been used to deposit CdZnS thin films on soda-lime glass substrates. The structural, morphological, optoelectronic properties of as-grown films have been investigated as a function of different Zn²⁺ precursor concentrations. The X-ray diffractogram of CdS thin-film reveals a peak corresponding to (002) plane with wurtzite structure, and the peak shift has been observed with the increase of the Zn²⁺ concentration upon formation of CdZnS thin film. From morphological studies, it has been revealed that the diluted chemical bath deposition technique provides homogeneous distribution of film on the substrate even at a lower concentration of Zn²⁺. Optical characterization has shown that the transparency of the film is influenced by Zn²⁺ concentration and when the Zn²⁺ concentration is varied from 0 M to 0.0256 M, bandgap values of resulting films range from 2.42 eV to 3.90 eV while. Furthermore, electrical properties have shown that with increasing zinc concentration the resistivity of the film increases. Finally, numerical simulation validates and suggests that CdZnS buffer layer with composition of 0.0032 M Zn²⁺ concentration would be a promising candidate in CIGS solar cell.     

Synthesis and Characterization of Hetero-metallic Oxides-Reduced Graphene Oxide Nanocomposites for Photocatalytic Applications

A new AgO.CuO.WO₃/rGO nanocomposite was designed for the investigation of the degradation ability of the hybrid material under visible light irradiation. The AgO, CuO, WO₃ NPs, and AgO.CuO.WO₃ hetero-metallic oxides were fabricated via the chemical co-precipitation method. The crystallite sizes and phase analyses were investigated by recording X-ray diffraction patterns. The crystallite sizes of three metal oxides in the AgO.CuO.WO₃ hetero metal oxide were 16.7, 15.9, and 16.9 nm, respectively. The FESEM images at various magnifications were probed to study the morphology of synthesized materials. The micrographs of hetero-metallic oxides AgO.CuO.WO₃ exposed that three metal oxides merged like small particles and gives a large bulbous appearance. EDX analyses confirmed the formation of required materials with high purity. FTIR data was in agreement with the literature which facilitated to ensure the purity of synthesized samples. The optical bandgap energy was calculated via the Tauc plot indicating that the blend of three metal oxides generated a new energy level in the electronic structure is suitable for photocatalysis in the presence of visible light. The bandgap energy of hetero metallic oxides was 1.25 eV which is less than individual metal oxides signifying the tuning of the bandgap. The incorporation of rGO in AgO.CuO.WO₃ hetero-metallic oxides gives a new photocatalyst for optimum photodegradation of methylene blue in minimum time. The percentage degradation via AgO.CuO.WO₃ was 87.20% in 70 min while the percentage degradation via AgO.CuO.WO₃/rGO recorded by photocatalytic experiment was 95% in 40 min. The photocatalysis data revealed that AgO.CuO.WO₃ hetero-metallic oxides-rGO nanocomposite ensured a strong potential to uptake organic dyes from water by promoting redox reactions during photocatalysis in the minimum time limit.     

Ordinary Gasoline Emissions Induce a Toxic Response in Bronchial Cells Grown at Air-Liquid Interface

Gasoline engine emissions have been classified as possibly carcinogenic to humans and represent a significant health risk. In this study, we used MucilAir™, a three-dimensional (3D) model of the human airway, and BEAS-2B, cells originating from the human bronchial epithelium, grown at the air-liquid interface to assess the toxicity of ordinary gasoline exhaust produced by a direct injection spark ignition engine. The transepithelial electrical resistance (TEER), production of mucin, and lactate dehydrogenase (LDH) and adenylate kinase (AK) activities were analyzed after one day and five days of exposure. The induction of double-stranded DNA breaks was measured by the detection of histone H2AX phosphorylation. Next-generation sequencing was used to analyze the modulation of expression of the relevant 370 genes. The exposure to gasoline emissions affected the integrity, as well as LDH and AK leakage in the 3D model, particularly after longer exposure periods. Mucin production was mostly decreased with the exception of longer BEAS-2B treatment, for which a significant increase was detected. DNA damage was detected after five days of exposure in the 3D model, but not in BEAS-2B cells. The expression of CYP1A1 and GSTA3 was modulated in MucilAir™ tissues after 5 days of treatment. In BEAS-2B cells, the expression of 39 mRNAs was affected after short exposure, most of them were upregulated. The five days of exposure modulated the expression of 11 genes in this cell line. In conclusion, the ordinary gasoline emissions induced a toxic response in MucilAir™. In BEAS-2B cells, the biological response was less pronounced, mostly limited to gene expression changes.     

New modified-majority voter-based efficient QCA digital logic design

ABSTRACT

Quantum-dot cellular automata (QCA) is an emerging nanotechnology and a possible alternative solution to the limitation of complementary metal oxide semiconductor (CMOS) technology. One of the most attractive fields in QCA is the implementation of configurable digital systems. This article presents a novel multifunctional gate called the modified-majority voter (MMV). The proposed gate works on the explicit interaction of the cell characteristic property for the implementation of digital circuits. This prominent feature of the proposed gate reduces the maximum hardware cost and implements highly efficient QCA structures. To verify the functionality of the proposed gate, some physical proofs, truth table and computational simulation results are performed. These results assured the validity of the existence of the proposed gate. It also dissipates less energy which has been calculated under three separate tunnelling energy levels using the QCAPro tool. To prove the effectiveness of the proposed MMV gate, several optimal irreversible arithmetic circuits such as three-input XOR, half-adder and full-adder are proposed. The modular layouts are verified with the freely available QCADesigner tool version 2.0.3.     

Computer aided diagnosis of brain abnormalities using texture analysis of MRI images

The drive of this study is to develop a robust system. A method to classify brain magnetic resonance imaging (MRI) image into brain-related disease groups and tumor types has been proposed. The proposed method employed Gabor texture, statistical features, and support vector machine. Brain MRI images have been classified into normal, cerebrovascular, degenerative, inflammatory, and neoplastic. The proposed system has been trained on a complete dataset of Brain Atlas-Harvard Medical School. Further, to achieve robustness, a dataset developed locally has been used. Extraordinary results on different orientations, sequences of both of these datasets as per accuracy (up to 99.6%), sensitivity (up to 100%), specificity (up to 100%), precision (up to 100%), and AUC value (up to 1.0) have been achieved. The tumorous slices are further classified into primary or secondary tumor as well as their further types as glioma, sarcoma, meningioma, bronchogenic carcinoma, and adenocarcinoma, which could not be possible to determine without biopsy, otherwise.     

Influence of different viscosity grade cellulose-based polymers on the development of valsartan controlled release tablets

This work is based on formulating and optimizing controlled release (CR) valsartan (160 mg) tablets using different viscosity grades of the cellulosic polymer. The objective was to develop an effective once-daily drug delivery system of this cardiovascular agent. Central composite design was used for designing the formulations. Polymers used were Methocel® K4M, K15M and K100M. Compatibility of excipients with active was studied through FT-IR. Micromeritic properties were determined and formulations exhibiting appropriate flow characteristics were compressed. Swelling behavior and in vitro buoyancy effect were studied and response surface curves were constructed to optimize the formulation. Multi-point dissolution profiles of valsartan CR tablets at pH 1.2, 4.5 and 6.8 were obtained. Model-dependent and model-independent methods were performed including f2, stability test as per ICH guidelines and ANOVA. FT-IR studies revealed the compatibility of valsartan with all excipients. Formulation K4T9 (containing 25% K4M polymer) was selected to be the best optimized trial, based on physical properties and controlled release profile (23% at 4 h, 82% at 16 h and 100% at 24 h). Results of buoyancy and swelling behavior indicated that HPMC-K4M polymer exhibited excellent floating lag time and swelling indexes. In vitro drug release kinetics showed that formulation K4T9 displayed Korsmeyer–Peppas drug release pattern with r value > 0.99. The manufacturing process of K4T9 was also found to be reproducible with a shelf life period of 41 and 36 months at room temperature and accelerated conditions, respectively. Valsartan CR matrix-based formulation was successfully prepared with Methocel K4M retardant.     

Trans-differentiation of human adipose-derived mesenchymal stem cells into cardiomyocyte-like cells on decellularized bovine myocardial extracellular matrix-based films

In this study, we aimed at fabricating decellularized bovine myocardial extracellular matrix-based films (dMEbF) for cardiac tissue engineering (CTE). The decellularization process was carried out utilizing four consecutive stages including hypotonic treatment, detergent treatment, enzymatic digestion and decontamination, respectively. In order to fabricate the dMEbF, dBM were digested with pepsin and gelation process was conducted. dMEbF were then crosslinked with N-hydroxysuccinimide/1-Ethyl-3-(3-dimethylaminopropyl)-carbodiimide (NHS/EDC) to increase their durability. Nuclear contents of native BM and decellularized BM (dBM) tissues were determined with DNA content analysis and agarose-gel electrophoresis. Cell viability on dMEbF for 3rd, 7th, and 14th days was assessed by MTT assay. Cell attachment on dMEbF was also studied by scanning electron microscopy. Trans-differentiation capacity of human adipose-derived mesenchymal stem cells (hAMSCs) into cardiomyocyte-like cells on dMEbF were also evaluated by histochemical and immunohistochemical analyses. DNA contents for native and dBM were, respectively, found as 886.11?±?164.85 and 47.66?±?0.09?ng/mg dry weight, indicating a successful decellularization process. The results of glycosaminoglycan and hydroxyproline assay, and sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE), performed in order to characterize the extracellular matrix (ECM) composition of native and dBM tissue, showed that the BM matrix was not damaged during the proposed method. Lastly, regarding the histological study, dMEbF not only mimics native ECM, but also induces the stem cells into cardiomyocyte-like cells phenotype which brings it the potential of use in CTE.     

Thermodynamic performance analysis of three solid oxide fuel cell and gas microturbine hybrid systems for application in auxiliary power units

In this study, three different configurations of a solid oxide fuel cell and gas microturbine hybrid system are evaluated for application in auxiliary power units. The first configuration is a common hybrid system in auxiliary power units, utilizing a fuel cell stack in the structure of the gas turbine cycle. The other configurations use two series and parallel fuel cell stacks in the structure of the gas turbine cycle. The main purpose of this research is thermodynamic analysis, evaluation of the performance of the proposed hybrid systems in similar conditions, and selection of an appropriate system in terms of efficiency, power generation, and entropy generation rate. In this study, the utilized fuel cells were subjected to electrochemical, thermodynamic, and thermal analyses and their working temperatures were calculated under various working conditions. Results indicate that the hybrid system with two series stacks had maximum power generation and efficiency compared with the other two cases. Moreover, the simple hybrid system and the system with two parallel stacks had relatively equal pure power generation and efficiency. According to the investigations, hybrid system with two series fuel cell stacks, which had 3424 and 1712 cells, respectively, can achieve the electrical efficiency of over 48%. A hybrid system with two parallel fuel cell stacks, in which each stack had 2568 cells, had the electrical efficiency of 46.3%. Findings suggested that maximum electrical efficiency occurred between the pressure ratios of 5–6 in the proposed hybrid systems.     

Effect of sand and clay fouling on the shear strength of railway ballast for different ballast gradations

Ballast contamination by fine materials such as sand and clay in railway track at arid regions is an important issue that causes track instability problems and settlement due to reduction of shear strength of ballast. In this paper, the results of direct shear box test conducted on clean ballast, sand-fouled ballast and clay-fouled ballast for different ballast gradations are reported and discussed. For this purpose, three different fouling amounts according to fouling index are added to clean ballast. Test results show that by increasing the fouling percentage, the ballast shear strength always decreases both for sand and clay fouled ballast. However, the amount of shear strength reduction is low at high normal stresses. Clay contamination has more adverse effect on the shear strength of ballast compared with sand contamination. Also, the results of tests for evaluation of gradation effect on shear strength of fouled ballast which are conducted on various gradations according to American Railway Engineering and Maintenance-of-Way Association, show that the maximum particle size as well as uniformity coefficient affect the shear strength of ballast. Also, an empirical equation is presented to observe the effect of ballast gradation on reduction of shear strength with regard to amount of fouling material and normal stress.