Effect of gamma irradiation on the optical properties of CR-39 polymer

The UV-Visible absorption spectra of virgin and gamma irradiated (20–800 kGy) CR-39 polymer have been deduced by using Shimadzu Double beam Double Monochromator UV-Visible Spectrophotometer (UV-2550). The existence of the peaks, their shifting and broadening as a result of gamma irradiation has been discussed. Finally the indirect and direct band gap in virgin and gamma irradiated CR-39 has been determined. The values of indirect band gap have been found to be lower than the corresponding values of direct band gap.     

A new method to estimate parameters of linear compartmental models using artificial neural networks

At present, the preferred tool for parameter estimation in compartmental analysis is an iterative procedure; weighted nonlinear regression. For a large number of applications, observed data can be fitted to sums of exponentials whose parameters are directly related to the rate constants/coefficients of the compartmental models. Since weighted nonlinear regression often has to be repeated for many different data sets, the process of fitting data from compartmental systems can be very time consuming. Furthermore the minimization routine often converges to a local (as opposed to global) minimum. In this paper, we examine the possibility of using artificial neural networks instead of weighted nonlinear regression in order to estimate model parameters. We train simple feed-forward neural networks to produce as outputs the parameter values of a given model when kinetic data are fed to the networks' input layer. The artificial neural networks produce unbiased estimates and are orders of magnitude faster than regression algorithms. At noise levels typical of many real applications, the neural networks are found to produce lower variance estimates than weighted nonlinear regression in the estimation of parameters from mono- and biexponential models. These results are primarily due to the inability of weighted nonlinear regression to converge. These results establish that artificial neural networks are powerful tools for estimating parameters for simple compartmental models.     

A Specific Stability Indicating Hplc Method to Determine Diclofenac Sodium in Raw Materials and Pharmaceutical Solid Dosage Forms

A high performance liquid chromatography method is described for the determination of diclofenac sodium, its related compounds and degradation products in commercial sources of raw materials and solid dosage forms. This method is specific, accurate and stability indicating. The method employs a reverse-phase octylsilane (C18) column with a mobile phase composed of acetonitrile/methanol/pic B-6 (25:25:50) and detection at 229 nm. The method resolves six principal related compounds with quantitation in the range 0.3-1.5%. Assay recoveries by spiking commercial formulations with diclofenac sodium were 99.64 ± 1.30%. Drug content in several commercial formulations are reported. Accelerated stability tests were conducted on raw materials and drug products and 1-(2,6-dichlorophenyl)-2-indolin-2-one was identified for the first time as a degradation product in solid dosage forms which are stressed under humidity and heat.     

Physiological Imaging Methods for Evaluating Response to Immunotherapies in Glioblastomas

Glioblastoma (GBM) is the most malignant brain tumor in adults, with a dismal prognosis despite aggressive multi-modal therapy. Immunotherapy is currently being evaluated as an alternate treatment modality for recurrent GBMs in clinical trials. These immunotherapeutic approaches harness the patient’s immune response to fight and eliminate tumor cells. Standard MR imaging is not adequate for response assessment to immunotherapy in GBM patients even after using refined response assessment criteria secondary to amplified immune response. Thus, there is an urgent need for the development of effective and alternative neuroimaging techniques for accurate response assessment. To this end, some groups have reported the potential of diffusion and perfusion MR imaging and amino acid-based positron emission tomography techniques in evaluating treatment response to different immunotherapeutic regimens in GBMs. The main goal of these techniques is to provide definitive metrics of treatment response at earlier time points for making informed decisions on future therapeutic interventions. This review provides an overview of available immunotherapeutic approaches used to treat GBMs. It discusses the limitations of conventional imaging and potential utilities of physiologic imaging techniques in the response assessment to immunotherapies. It also describes challenges associated with these imaging methods and potential solutions to avoid them.     

Micellar association in simultaneous presence of organic salts/additives

Viscosity measurements under Newtonian flow conditions had been performed on cetyltrimethylammonium bromide (CTAB) aqueous solutions in the combined presence of sodium salts of aromatic acids (sodium salicylate, NaSal; sodium benzoate, NaBen; sodium anthranilate, NaAn) and organic additives (1-hexanol, C₆OH; n-hexylamine, C₆NH₂) at 30°C. On addition of C₆OH or C₆NH₂, the viscosity of 25 mM CTAB solution remained nearly constant without salt as well as with a lower salt concentration. This is due to low CTAB concentration which is not sufficient to produce structural changes in this concentration range of salts. However, as the salt concentration was increased further, the effect of C₆OH/C₆NH₂ addition was different with different salts: The viscosity first increased; then a decrease was observed with the former while with C₆NH₂ a decrease followed by constancy appeared in plots of relative viscosities (η _r ) vs. organic additive concentrations. At further higher salt concentration, the magnitude of η _r was much higher. The viscosity increase is explained in terms of micellar growth and the decrease in terms of swollen micelle formation (due to interior solubilization of organic additive) or micellar disintegration (due to formation of water + additive pseudophase).     

Correction to: Attention-based multimodal contextual fusion for sentiment and emotion classification using bidirectional LSTM

Multimedia Tools and Applications - A Correction to this paper has been published: https://doi.org/10.1007/s11042-021-10591-y     

Fabrication and characterization of electrospun psyllium husk-based nanofibers for tissue regeneration

The present study reports for first time the blending of psyllium husk (PH) powder/gelatin (G) in the polymer-rich composition of polyvinyl alcohol (PVA) to make an electrospinnable solution. The composite was prepared in 3 different ratios viz., 100% (wt/wt) (PVA + PH), 75% + 25% (PVA + 75PH + 25G) (wt/wt) and 50% + 50% (PVA + 50PH + 50G) (wt/wt) in 6% PVA solution. Optimum electrospinning parameters were evaluated for all the prepared blends. The fabricated nanofibers were characterized by scanning electron microscopy (SEM), attenuated total reflectance-Fourier transform infrared, differential scanning calorimetry, porosity percentage, and fiber orientation using ImageJ software. A qualitative in vitro degradation study at room temperature is supported by SEM images. The cellular interactions were characterized by MTT assay of NIH-3T3 fibroblast cells for 2 and 4 days with an optimum cell growth of >50% by fourth day of culture and long-term cultivation of L929-RFP cells was observed for 10 days. The nanofibers were formed in the range of 49–600 nm. PVA + 75PH + 25G when cultured with L929-RFP cells exhibited highest fluorescence intensity and thus supported cellular proliferation significantly. Based on the results obtained from various analyses, we anticipate that fabricated psyllium-based nanofiber can be used as a promising candidate for wound healing and other biomedical applications.     

Accuracy improvement method for flank milling surface design

In this paper, a variation of the method of designing surfaces for flank milling proposed by Li et al. 2006 (Surface design for flank milling. Submitted to CAD, July) is presented. Li’s method is based on the premise that the surface flank milled by a cylindrical tool can be represented by a NURBS surface and can be used by designers to build efficient impellers, blades and other engineering parts. In the proposed method, a four control point curve is used to approximate the grazing curves and for subsequent generation of a polynomial surface. This eliminates the need of weights for the interior control points and still results in a good surface. The accuracy of the surface can be controlled by adding control points. Examples are given to demonstrate the proposed surface design method.