Transient liquid phase sintering of high-purity mullite for high-temperature structural ceramics

High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere.     

Re-evaluation of Radiation-Energy Transfer to an Extraction Solvent in a Minor-Actinide-Separation Process Based on Consideration of Radiation Permeability

ABSTRACT

Absorbed-dose estimation is essential for evaluation of the radiation tolerance of minor-actinide-separation processes. We propose a dose-evaluation method based on radiation permeability, with comparisons of heterogeneous structures seen in the solvent-extraction process, such as emulsions forming in the mixture of the organic and aqueous phases. A demonstration of radiation-energy-transfer simulation is performed with a focus on the minor-actinide-recovery process from high-level liquid waste with the aid of the Monte Carlo radiation-transport code PHITS. The simulation results indicate that the dose absorbed by the extraction solvent from alpha radiation depends upon the emulsion structure, and that from beta and gamma radiation depends upon the mixer-settler-apparatus size. Non-negligible contributions of well-permeable gamma rays were indicated in terms of the plant operation of the minor-actinide-separation process.     

Radiophotoluminescence phenomenon in copper-doped aluminoborosilicate glass

Radiophotoluminescence phenomena have been widely investigated on various types of materials for dosimetry applications. We report that an aluminoborosilicate glass containing 0.005 mol% copper exhibits intense photoluminescence in the visible region induced by X-ray and γ-ray irradiation. The luminescence is assigned to the 3d⁹4s¹ → 3d¹⁰ transition of Cu⁺. The proportionality of the intensity of the induced photoluminescence to the irradiation dose was confirmed up to 0.5 kGy using ⁶⁰Co γ-ray irradiation. Based on the spectroscopic results, a potential mechanism was proposed for the enhancement of the photoluminescence. The exposure to the ionizing radiation generates electron-hole pairs in the glass, and the electrons are subsequently captured by the Cu²⁺ ions, which are converted to Cu⁺ and emit the luminescence. For the glass containing 0.01 mol% copper, the pronounced enhancement of the photoluminescence was not observed because the reverse reaction, ie, the capture of the holes by the Cu⁺ ions, becomes prominent. The photoluminescence induced by the irradiation was stably observed for the glasses kept at room temperature and even for the glasses heat-treated at 150°C. However, the induced photoluminescence could be eliminated by the heat treatment at a temperature at 500°C, and the glass returned to the initial pre-irradiation state. The Cu-doped aluminoborosilicate glass is a potential candidate for use in dosimetry applications.     

Supramolecular Zn(II)-Dipicolylamine-Azobenzene-Aminocyclodextrin-ATP Complex: Design and ATP Recognition in Water

Cyclodextrins (CyDs) are water-soluble host molecules possessing a nanosized hydrophobic cavity. In the realm of molecular recognition, this cavity is used not only as a recognition site but also as a reaction medium, where a hydrophobic sensor recognizes a guest molecule. Based on the latter concept, we have designed a novel supramolecular sensing system composed of Zn(II)-dipicolylamine metal complex-based azobenzene (1-Zn) and 3A-amino-3A-deoxy-(2AS,3AS)-γ-cyclodextrin (3-NH₂-γ-CyD) for sensing adenosine-5′-triphosphate (ATP). 1-Zn showed redshifts in the UV-Vis spectra and induced circular dichroism (ICD) only when both ATP and 3-NH₂-γ-CyD were present. Calculations of equilibrium constants indicated that the amino group of 3-NH₂-γ-CyD was involved in the formation of supramolecular 1-Zn/3-NH₂-γ-CyD/ATP. The Job plot of the ICD spectral response revealed that the stoichiometry of 1-Zn/3-NH₂-γ-CyD/ATP was 2:1:1. The pH effect was examined and 1-Zn/3-NH₂-γ-CyD/ATP was most stable in the neutral condition. The NOESY spectrum suggested the localization of 1-Zn in the 3-NH₂-γ-CyD cavity. Based on the obtained results, the metal coordination interaction of 1-Zn and the electrostatic interaction of 3-NH₂-γ-CyD were found to take place for ATP recognition. The “reaction medium approach” enabled us to develop a supramolecular sensing system that undergoes multi-point interactions in water. This study is the first step in the design of a selective sensing system based on a good understanding of supramolecular structures.     

Direct Observation of Pure Cu and Cu-Ag Anode Passivation in H2SO4-CuSO4 Aqueous Solution by Channel Flow Double Electrode and Optical Microscopy

Metallurgical and Materials Transactions B - The dissolution and passivation of pure Cu and Cu-5 wt pct Ag anodes in H2SO4-CuSO4 electrolyte were investigated by a direct...     

Eu@C86 isomers: Calculated relative populations

Abstract

Relative populations of four energy-lowest IPR (isolated-pentagon-rule) isomers of Eu@C₈₆ are computed using the Gibbs energy based on characteristics from density functional theory calculations (M06-2X/3-21G?～?SDD entropy term, M06-2X/6-31G*～SDD or B2PLYP(D)/6-31G*～SDD energetics). The calculations confirm that the recently isolated Eu@C₁(7)-C₈₆ species is a major isomer in a relevant temperature region. Relationship to the empty C₈₆ cages is discussed, too.     

Cover Image,Volume 69, Issue 3

The cover image is based on the Mini‐Review Well‐defined, environment‐friendly synthesis of polypeptides based on phosgene‐free transformation of amino acids into urethane derivatives and their applications by Takeshi Endo et al., https://doi.org/10.1002/pi.5952 . Cover image © Takeshi Endo Images.

     

EFFECT OF DEVELOPER PROPERTIES ON PRINT QUALITY

We investigated the dependence of the toner charge-to-mass ratio (q/m) in a two-component electrophotographic developer on the shaking time, toner concentration (T/C), carrier sizes, and the carrier core and the coating materials, as well as the resulting print qualities in terms of print density, background density, tone reproduction, resolution, and dot gain. Four different sizes of spherical ferrite carriers, four different carrier coating materials, and an irregular iron carrier were used with two types of toner: 14 um red toner (NP-4080) and 8 um cyan toner (CLC-500). The q/m measurement by the blow-off method showed that the red toner charge was positive while the cyan toner charge was negative with these carriers. The toner q/m values, which depended on the shaking time and decreased with the increasing T/C were much more affected by the larger carrier and the smaller toner. The carriers which yielded charges in the proper range produced better print qualities than did the other carriers that yielded a toner q/m     

A method of identifying latent human errors in work systems

Work system improvements are implemented in various manufacturing processes to prevent problems caused by human errors. However, they are almost always applied to problems which have already occurred. This paper examines a method of identifying latent human errors existing within the work systems beforehand. A procedure for applying failure mode and effect analysis to this identification problem was defined based on over 1000 empirical errors: a work system decomposition criterion and fundamental error modes for listing latent human errors, and then applied to three practical manufacturing processes in order to evaluate its effectiveness.     

Efficiency of repeated batch penicillin fermentation using two fermentors. Computer simulation and optimisation

Repeated batch operation using two fermentors (RBTF) to penicillin fermentation was demonstrated by computer simulation to improve productivity. Three operation modes were compared: chemostat, repeated batch operation using a single fermentor (RBSF) and RBTF; in each case account was made of the lag period before growth. The simulated fermentor performances were assessed on the basis of the penicillin productivity and concentration; the simulation was based on published batch fermentation data. It was shown that RBTF was superior to RBSF and chemostat. The advantage of RBTF increased as the lag period became greater.