Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

Adaptive motion control using neural network approximations

In this paper, we present a new adaptive technique for tracking control of mechanical systems in the presence of friction and periodic disturbances. Radial Basis Functions (RBFs) are used to compensate for the effects of nonlinearly occurring parameters in the friction and periodic disturbance model. Theoretical analysis, such as stability and transient performance, is provided. Furthermore, the performance of the adaptive RBF controller and its non-adaptive counterpart are compared.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Topology preservation of template-based 6-subiteration reduction operations

Generally, a reduction operation (e.g., thinning and shrinking) on 3D binary images can be represented as a set of reduction templates where every object voxel of the image satisfying any template is turned to a background voxel. Generally, it is rather difficult, error-prone and time-consuming for verifying the topological soundness of a 3D parallel reduction operation. This paper proposes sufficient conditions of time complexity O(n) for verifying the topological soundness of 3D parallel 6-subiteration reduction operations of n templates where such a kind of 3D reduction operations is performed alternatively from the six orthogonal directions to turn object voxels to background voxels. By such sufficient conditions, the topology soundness of a 3D 6-subiteration parallel reduction operation can be verified by checking each and every of its templates.     

Control of discrete time nonlinear systems with a time-varying structure

In this paper, we present a control methodology for a class of discrete time nonlinear systems that depend on a possibly exogenous scheduling variable. This class of systems consists of an interpolation of nonlinear dynamic equations in strict feedback form, and it may represent systems with a time-varying nonlinear structure. Moreover, this class of systems is able to represent some cases of gain scheduling control, Takagi-Sugeno fuzzy systems, as well as input-output realizations of nonlinear systems which are approximated via localized linearizations. We present two control theorems, one using what we call a “global” approach (akin to traditional backstepping), and a “local” approach, our main result, where backstepping is again used but the control law is an interpolation of local control terms. An aircraft wing rock regulation problem with varying angle of attack is used to illustrate and compare the two approaches.     

Stability robustness of networked control systems with respect to packet loss

This paper is concerned with stability analysis of discrete-time networked control systems over a communication channel subject to packet loss whose behavior is modeled by an i.i.d Bernoulli process with a packet dropping probability bounded by a constant. A necessary and sufficient condition for stability is obtained. A packet dropping margin is introduced as a measure of stability robustness of a system against packet dropping, and a formula for it is derived. A design method is proposed for achieving a large margin subject to a constraint that the system has a set of prescribed nominal closed-loop poles.     

Decentralized adaptive coordinated control of multiple robot arms without using a force sensor

This paper presents a distributed adaptive coordinated control method for multiple robot arms grasping a common object. The cases of rigid contact and rolling contact are analyzed. In the proposed controller, the dynamic parameters of both object and robot arms are estimated adaptively. The desired motions of the robot arms are generated by an estimated object reference model. The control method requires only the measurements of the positions and velocities of the object and robot arms, but not the measurements of forces and moments at contact points. The asymptotic convergence of trajectory is proven by the Lyapunov-like Lemma. Experiments involving two robot arms handling a common object are shown.