Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

Theoretical model for flash generation

Reduction of flash generated in a gas vent is of great concern for manufacturers of electronic parts. The present study proposes a theoretical model for flash generation through consideration of flow characteristics in a gas vent. The model predicts the factors controlling flash, i.e., material parameters such as zero‐shear viscosity, crystallization temperature, thermal conductivity, and heat capacity, and process parameters such as injection and mold wall temperatures, packing pressure, and the clearance of a gas vent. On the other hand, we measure the amount of flash generated in the molding of poly(phenylene sulfide) (PPS) composites containing glass fiber and spherical fillers (CaCO₃ or Al₂O₃). Flash reduces with decreasing size of spherical fillers. These experimental data are successfully interpreted using the flash model. Polym. Eng. Sci., 45:198–206, 2005. © 2005 Society of Plastics Engineers     

The significance of urinary N-acetyl-beta-D-glucosaminidase for predicting early stage diabetic nephropathy

We studied urinary N-acetyl-beta-D-glucosaminidase (NAG) in the early stage of diabetic nephropathy in 27 non-insulin-dependent diabetes mellitus (NIDDM) patients with a microalbumin level below 20 mg on 24-hour urine sample. Microalbumin and NAG excretion were measured in 24-hour urine samples collected on three separate occasions within seven days of admission. Creatinine clearance was determined simultaneously. There was a significant negative correlation between the creatinine clearance and 24-hour urinary NAG (r = -0.38, p < 0.05). Elevation of urinary NAG may indicate decreased renal function during early stage NIDDM nephropathy.     

Thermal response in thermal energy storage material around heat transfer tubes: effect of additives on heat transfer rates

The effects of carbon-fiber chips and carbon brushes as additives on the thermal conductivity enhancement of phase change materials (PCMs) using in latent heat thermal energy storage are investigated experimentally and numerically by considering the wall effect of the additives. The carbon-fiber chips are effective for improving the heat transfer rate in PCMs. However, the thermal resistance near the heat transfer surface is higher than that for the carbon brushes. As a result, the overall heat transfer rate for the fiber chips is lower than that for the carbon brushes. Consequently, the carbon brushes are superior to the fiber chips for the thermal conductivity enhancement under the present experimental conditions. The carbon brushes are moreover applied to the packed beds of particles to overcome their low thermal conductivity in chemical heat pump/storage. The carbon brushes essentially improve the heat transfer characteristics in the packed beds, though the thermal resistance is observed because the particles obstruct contact between the fibers and the heat transfer surfaces.     

A study of suppression of vapor explosions by adding inversely soluble polymers

The mechanism of the suppression of vapor explosions by adding inversely soluble polymers in water is studied. Vapor explosion experiments and quench experiment are conducted using a silver test piece. Polymetric solution (polyethylene oxide), of concentrations from 0 to 500 wppm, whose normalized viscosity (by water) varies from 1.00 to 2.00, is used. No vapor explosion is observed in the aqueous polymer solution at a concentration higher than 200 wppm. Quench experiments using the silver test piece submerged in the polymer solution and water are performed in order to examine the stability of film boiling. The suppression of the vapor film collapse is attributed to the precipitation of polyethylene as a gel around the vapor film. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(4): 297–306, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10037     

Inhibition of natural killer cell cytotoxicity by cell growth-related molecules

Certain MHC class I molecules on target cells are known to inhibit the cytotoxic action of NK cells. By using monoclonal antibody (mAb) Cho-1, we have found inhibitory non-MHC class I cell surface molecules that are noncovalently-associated with 200 kDa and 40 kDa antigens. Poly I-C-induced rat NK cells were not cytotoxic to rat fetus-derived fibroblast WFB cell line. In contrast, NK cells were cytotoxic to H-ras oncogene-induced transformants of WFB, W14 and W31. FACS analysis indicated that mAb Cho-1 reacts with WFB, but not with W14 and W31 cells. Thus, this antigen may disappear concomitantly with cell growth and transformation. Cho-1 antigens were also expressed on other NK-resistant lines, such as mouse BALB3T3 fibroblast, EL-4 lymphoma and human fibroblast HEPM. However, they were not expressed on NK-sensitive mouse YAC-1 and H-ras transformant (Brash) of BALB3T3 cells. Furthermore, treatment of target cells with IFN-gamma clearly induced the cell surface expression of Cho-1 antigens, and conferred a resistance to NK cytolysis on target cells. These data strongly suggest that Cho-1 antigen expression may correlate with target cell susceptibility to NK cells. Indeed, treatment of NK-resistant WFB as well as HEPM cells with F(ab')2 fragments of mAb Cho-1 resulted in the acquisition of susceptibility to NK cytolysis. Cho-1 antigens may be novel molecules that regulate the NK resistance of cells.     

Detection of hypervascular hepatocellular carcinoma by using spiral volumetric CT: comparison of US and MR imaging

BACKGROUND: Most hepatocellular carcinomas (HCCs) are hypervascular and arise in the liver with chronicity. Spiral volumetric CT (SVCT) is a new rapid-scan technique that offers whole-liver scanning during the arterial-dominant phase. The main aim of the present study is to evaluate the detectability of hypervascular HCC with SVCT as compared with ultrasonography (US) and magnetic resonance (MR) imaging. METHODS: Forty-three hypervascular HCCs in 512 patients with chronic liver disease were examined with US, precontrast SVCT, postcontrast SVCT during the arterial-dominant phase (CT-ADP) and during the equivalent-phase (CT-EP) noncontrast MR imaging and angiography including SVCT during arteriography and arterial portography. Angiographic and follow-up findings were used as the gold standard if the lesion was not confirmed histologically. RESULTS: The sensitivity was 61% with precontrast CT, 84% with CT-ADP, 58% with CT-EP, 70% with US, 72% with MR, and 95% with the combination of these five modalities. Five HCCs (12%) were detected with only CT-ADP. The vascularity of HCC was correctly evaluated as hypervascular in 38 nodules (88%) with the combination of precontrast CT and CT-ADP. CONCLUSIONS: We suggest that the combination of precontrast SVCT and CT-ADP is an essential modality to screen for HCC in patients with chronic liver disease. CT-EP did not contribute to the detection of hypervascular HCC.     

Effect of cation structure on the electrochemical and thermal properties of ion conductive polymers obtained from polymerizable ionic liquids

Several onium cations having vinyl group formed ionic liquids after coupling with bis(trifluoromethanesulfonyl)imide. These monomers were polymerized, and the relation between onium cation structure and properties of thus polymerized ionic liquids was investigated. The polymerized ionic liquid having ethylimiadzolium cation unit showed the highest ionic conductivity of around 10⁻⁴ S cm⁻¹ at 30 °C among the obtained polymers reflecting the lowest glass transition temperature of −59 °C. These polymers were thermally stable and their decomposition temperatures were about 350 °C. The ionic conductivity of the polymerized ionic liquids decreased by both the addition of lithium bis(trifluoromethanesulfonyl)imide and the polymerization in the presence of cross-linker. However, the polymerized ionic liquid having 1-methylpiperidinium cation structure showed good lithium ion transference number of 0.43 at room temperature.     

Polymerization of 2-dibutylamino-1,3,5-triazine-4,6-dithiol on wire during friction process

2-Dibutylamino-1,3,5-triazine-4,6-dithiol (DB) and a mixture of DB and triallylisocyanurate (TAIC) were used as a lubricant during steel wire drawing due to a dry process. DB gave a polymer film with 180 nm in thickness to wire surfaces during the wire drawing. The polymer film had a disulfide structure on the backbone and contained a small amount of DB monomer and olygomer. Molecular weight and polymer weight increased with the drawing rate. The mixture of DB and TAIC gave mainly a three-dimensional polymer film with 225 nm in thickness to wire surfaces during drawing. The polymer film insoluble in THF had mono and disulfide structures and contained a small amount of linear polymer, DB, and TAIC. Such tribological polymerizations are estimated as follows: DB produces dithiyl radicals on a nascent surface formed during drawing and in the presence of oxygen and heat. The dithiyl radicals were polymerized by coupling with each other to give disulfide bonds or added to allyl groups in TAIC to give monosulfide bonds. It is concluded that this technique should be possible to use for unifying metal processing and surface treatment. © 1995 John Wiley & Sons, Inc.     

Separation of Polyvinyl Chloride from Plastic Mixture by Froth Flotation after Surface Modification with Ozone

Selective modification by ozonation for the surface of polyvinyl chloride (PVC) was evaluated to separate PVC from the other plastics, polyethylene terephthalate (PET), polycarbonate (PC) and polymethyl methacrylate (PMMA), with almost the same density as PVC by the froth flotation process. Ozonation could selectively decrease the contact angles of flexible PVC from 87.5 degrees to 68.4 degrees and rigid PVC from 90.3 degrees to 66.9 degrees, whereas little decreases in the contact angle were observed for other plastics. This would be due to the replacement of the chloride group on the surface of PVC, into hydrophilic functional groups; carbonyl, carboxyl and ester group. The PVC was successfully separated from the other plastics by the froth flotation process after the selective surface modification by ozonation.