MHD mixed convection of a Cu–water nanofluid flow through a channel with an open trapezoidal cavity and an elliptical obstacle

In the current work, numerical simulations are achieved to study the properties and the characteristics of fluid flow and heat transfer of (Cu–water) nanofluid under the magnetohydrodynamic effects in a horizontal rectangular canal with an open trapezoidal enclosure and an elliptical obstacle. The cavity lower wall is grooved and represents the heat source while the obstacle represents a stationary cold wall. On the other hand, the rest of the walls are considered adiabatic. The governing equations for this investigation are formulated, nondimensionalized, and then solved by Galerkin finite element approach. The numerical findings were examined across a wide range of Richardson number (0.1 ≤ Ri ≤ 10), Reynolds number (1 ≤ Re ≤ 125), Hartmann number (0 ≤ Ha ≤ 100), and volume fraction of nanofluid (0 ≤ φ ≤ 0.05). The current study's findings demonstrate that the flow strength increases inversely as the Reynolds number rises, which pushes the isotherms down to the lower part of the trapezoidal cavity. The Nu_avg rises as the Ri rise, the maximum Nu_avg = 10.345 at Ri = 10, Re = 50, ϕ = 0.05, and Ha = 0; however, it reduces with increasing Hartmann number. Also, it increase by increasing ϕ, at Ri = 10, the Nu_avg increased by 8.44% when the volume fraction of nanofluid increased from (ϕ = 0–0.05).     

Assessment of technological attributes of autochthonous starter cultures in Turkish dry fermented sausage (sucuk)

The study aims to evaluate the technological properties of autochthonous strains (Lactobacillus sakei S15, Lactobacillus plantarum S24, L. plantarum S91, Pediococcus pentosaceus S128b and Staphylococcus carnosus G109) in Turkish dry fermented sausage (sucuk). After 24 h of fermentaPtion, all lactic acid bacteria strains reduced the pH to below 5.0, while the pH in the control group was above 5.3. The number of lactic acid bacteria strains reached 10⁸–10⁹ cfu g⁻¹ during fermentation. Staphylococcus carnosus G109 remained at the inoculation level of 10⁶ cfu g⁻¹ during ripening. Lactobacillus sakei S15 as mono-culture showed higher TBARS values compared to other strains. The control group had the lowest L* value and autochthonous strains caused no significant difference for a* value. According to principal component analysis results, most volatile compounds were positively correlated with the group containing only L. sakei S15.     

Effect of Messaging Model on the Reliable Data Transfer Latency in a Fog System

Journal of Network and Systems Management - IoT applications have become a pillar for enhancing the quality of life. However, the increasing amount of data generated by IoT devices places pressure...     

New local binary pattern approaches based on color channels in texture classification

Multimedia Tools and Applications - In this paper, four novel, simple and robust approaches, which are left to right local binary patterns (LBPLL2R), top to down local binary patterns (LBPT2D),...     

Hemocompatibility,cytotoxicity, and genotoxicity of poly(methylmethacrylate)/nanohydroxyapatite nanocomposites synthesized by melt blending method

The aim of this study was to show the hemocompatibility, cytotoxicity, and genotoxicity of nanocomposites that were synthesized with different molecular weights of poly(methyl methacrylate) (PMMA) and different concentrations of nanohydroxyapatite (nHAp). Different techniques to characterize the nanocomposites were used. The cytotoxicity and genotoxic effects of the polymers and nanocomposites on human lymphocytes were determined by acid phosphatase assay, viability test, and comet assay. Moreover, hemocompatibility test was performed. It was found that all of the PMMA/nHAp nanocomposites are highly hemocompatible and biocompatible, none of the nanocomposites showed a cytotoxic effect, and nHAp addition decreased the genotoxicity.     

Wind turbine speed control of a contactless piezoelectric wind energy harvester

ABSTRACT

Wind turbine control is an important task to make the electricity generation secure in terms of energy demand and machine safety. It also yields to control the desired power level and optimized energy because of the assignment of turbine speed. The contactless piezoelectric wind energy harvester (CPWEH) used in this study has three piezoelectric layers located around the shaft with 120 degrees apart and they are buckled by the magnetic force without any physical contact. The superiority of this device is to generate energy for low wind speeds such as 1.5 m/s. However, for high speeds, high total harmonic distortions (THDs) govern the waveforms, thus controlling the turbine speed becomes necessary for optimizing the output power. Encouraged by this, a small low inertia dc generator is coupled with the wind turbine, and the generator terminals are connected to a resistor through a power switch to generate a braking torque that opposes to wind speed direction. By controlling the switch properly, turbine speed is ensured to remain within a certain band, which accordingly prevents the turbine from rotating very fast at damaging wind speeds. Several experiments are performed on the developed CPWEH with/without the presented control scheme which prove the existence of promising performance of our proposal.     

Effect of Ti amount on wear and corrosion properties of Ti-doped Al2O3 nanocomposite ceramic coated CP titanium implant material

Al₂O₃ and Ti-doped Al₂O₃ nanocomposite ceramic coatings were prepared by using a sol-gel dip-coating process. Corrosion and wear resistance of Al₂O₃ ceramic coatings in relation to Ti amount were carried out using pin-on-disk tribotester, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). Surface characterizations before and after the corrosion and wear tests were investigated by the scanning electron microscope (SEM) and X-ray diffraction (XRD) and hardness analysis. The results of corrosion and wear tests exhibited that the corrosion and wear resistance of nanocomposite ceramic coatings became better than uncoated samples. Also, corrosion and wear resistance of nanocomposite ceramic coatings improved with Ti doping content increased.     

Refinement of primary carbides in AISI DC 53 cold work tool steel by thin section copper permanent mould casting and water atomization

In this study, as alternative methods to conventional production methods involving thin section copper permanent mould casting (fast solidification) and water atomization (rapid solidification) of AISI DC 53 cold work tool steel have been investigated. Thin slabs obtained by copper mould casting was homogenized at 1150 °C for one hour and then hot rolling was be applied. After hot rolling, conventional heat treatment have been applied to thin slabs. The same heat treatment procedure have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. In order to investigate also the effect of rapid solidification on AISI DC 53 tool steel, steel powder was produced by water atomization technique. Experiments have revealed that thin steel slabs in permanent copper mould and rapidly solidified tool steel powder by water atomization have a more refined primary M₇C₃ carbides than commercially available steel.