Silicone-coated polyimide films deposited by surface dielectric barrier discharges

Hybrid dielectric barrier discharges are investigated for plasma generated on the surface of a dielectric layer, where two conducting electrodes of high voltage and ground are formulated on the upper and bottom surfaces. Using a flexible thin polyimide-film of a thickness ranging from 25 to 125 μm, a plasma is generated with a voltage of about 1 kV and a frequency of 40 kHz.However, the surface of the dielectric layer was etched through a chemical reaction involving plasma oxygen radical species, and thus the polyimide films failed readily, resulting in dielectric breakdown within short operating time ranging from a few minutes to several tens of minutes,based on the film thicknesses of 25 μm and 125 μm, respectively. These plasma erosions were prevented by coating the polyimide surface with a 25 μm thick silicone paste. The siliconecoated film surface was then reinforced remarkably against plasma erosion as the organic polymer was vulnerable to chemical reaction of the plasma species, while the inorganic silicone exhibited a high chemical resistance against plasma erosion.     

Optical diffraction gratings embedded in BK-7 glass by low-density plasma formation using femtosecond laser

The optical embedded diffraction gratings with the internal refractive index modification in BK-7 glass plates were demonstrated using low-density plasma formation excited by a high-intensity femtosecond (130 fs) Ti: sapphire laser (λp=790 nm). The refractive index modifications with diameters ranging from 400 nm to 4 μm were photoinduced after plasma formation occurred upon irradiation with peak intensities of more than 1×1013 W/cm2. The graded refractive index profile was fabricated to be a symmetric around the center of the point at which low-density plasma occurred. The maximum refractive index change (Δn) was estimated to be 1.5×10-2. Several optical embedded gratings in BK-7 glass plate were demonstrated with refractive index modification induced by the scanning of low-density plasma formation.     

PURIFICATION AND CHARACTERIZATION OF POLYPHENOL OXIDASE FROM POTATO: I. PURIFICATION AND PROPERTIES

Polyphenol oxidase (Isozyme I) from potato was extracted and purified with ammonium sulfate, cation-exchange (Bio-Rad Bio-Scale S2) and Sephadex G-100 column chromatography. The enzyme was purified 11.8 fold resulting in a specific activity of 250.3 units/mg. Optimum pH of the enzyme was 6.6. Optimum temperature of the enzyme was 40C and its half-life was 0.8 min at 70C. The K_mfor catechol, pyrogallol, 4-methyl catechol, caffeic acid and L-DOPA were 4.11 mM, 0.61 mM, 0.78 mM, 0.50 mM and 32 mM, respectively. However, monophenols such as tyrosine, p-cresol and 1-naphtol did not show any activity. Data for V_max/K_m which represents catalytic efficiency show that 4-methyl catechol has the highest value. The molecular weight of the active enzyme was 86,000 Da, composed of two identical subunits. The number of Cu²⁺ ions bound was found to be 2 per enzyme molecule.     

Effects of honing treatment on AIP-TiN and TiAlN coated end-mill for high speed machining

The objective of this work is to compare the tool performance of TiN and TiAlN coated carbides end-mills deposited by an arc ion plating (AIP) method, using honing treatment to polish the cutting edge surface sleekly. The curve of surface roughness versus honing time showed a rapid improvement initially and thereafter became steady, manifesting a saturation effect. The optimal honing time related to surface roughness was determined to be approximately 20 s. As the surface roughness increased, the critical loads reduced. At an average surface roughness (Ra) of 0.028 μm, the highest critical loads of TiN and TiAlN coating layers were 98 and 114 N, respectively. Tool performances of uncoated and coated tools were conducted under high speed machining (HSM) of AISI D2 cold-worked die steel (62 HRC). Consequently, the TiAlN coated end-mill using honing treatment showed excellent tool life under HSM conditions.     

Microstructure comparison of ZK60 alloy under casting, twin roll casting and hot compression

The microstructures of ZK60 alloy under conventional direct as-casting (DC),twin roll casting (TRC) and twin roll casting followed by hot compression (TRC-HC) were analyzed by optical morphology (OM),electron backscatter diffraction (EBSD) and X-ray diffraction (XRD).The deformation condition of hot compression is 350 ℃,0.1 s?1.The microstructural evolution under TRC-HC deformation followed by annealing at different temperatures and time was discussed.The results show that TRC provides more modified microstructure compared with DC.Twins are found in TRC processing;dynamic recrystallization (DRX),shear bands and twins are found in TRC-HC.A short annealing time has little effect on hardness,while during a long time annealing,it is found that low annealing temperatures increase the micro-hardness and high temperature decreases it.     

Fatigue crack in large-scale tubular joints for offshore structures

Tubular members have been used for constructing offshore structures. Large-scale fatigue tests of welded tubular K-joints under the balanced in-plane bending brace were carried out to investigate the fatigue behavior of API 2W Gr.50 steel produced by POSCO. The experimental results were verified by numerical approaches and compared with the IIW, DnV RP-C203 and API RP 2A-WSD design curves. The test results based on the hot spot stress were in agreement with the design curves. The SCF factor for tubular K-jo...     

Surface effects of hybrid vibration-assisted femtosecond laser system for micro-hole drilling of copper substrate

The ultrafast laser based hybrid machining system was studied and a novel approach was demonstrated to improve laser machining quality on metals by vibrating the optical objective lens with a low frequency (500 Hz) and various displacements (0-16.5 μm) during a femtosecond laser machining process.The laser used in this experiment is an amplified Ti:sapphire femtosecond (10-15 s) laser system that generates 100 femtosecond pulses having an energy of 3.5 mJ/pulse with a 5 kHz repetition rate at a central wavelength of 790 nm.It is found that both the wall surface finish of the machined structures and the aspect ratio obtained using the frequency vibration assisted laser machining are improved compared with those derived via laser machining without vibration assistance.     

甲烷/空气预混合气在定容燃烧室内的燃烧试验

为研究进气温度、进气压力、当量燃烧比、射流引燃、压燃(自燃)等对甲烷燃烧的影响,以提高点燃式天然气发动机的性能,在定容燃烧室(CVCC)内进行甲烷/空气预混合气的燃烧试验,通过火焰高速摄影和气体压力测量等手段,获取试验结果并进行分析.试验发现,在燃烧室内安装带通孔的横隔板后,有利于加快火焰传播速度、提高燃烧峰值压力和燃烧的稳定性,在某些试验条件下,下燃烧室会出现混合气压燃(自燃)现象.     

Fuel combustion test in constant volume combustion chamber with built-in adaptor

Combustion tests of pre-mixture of methane and air in constant volume combustion chamber(CVCC) have been carried out by means of flame propagation photo and gas pressure measurement,the effects of CVCC body temperature,intake pressure of pre-mixture of methane and air,equivalence ratio and location of the built-in adaptor have been investigated.The whole combustion chamber can be divided into two parts,i.e.the upper combustion chamber and the lower combustion chamber,by the built-in adaptor with through hol...