Conceptual damage-sensitive features for structural health monitoring: Laboratory and field demonstrations

The use of damage-sensitive features to evaluate structural condition or health is a very critical aspect of structural health monitoring. The purpose of this paper is to investigate the potential of two different damage-sensitive features for detecting damage. Different damage scenarios are simulated on a large-scale laboratory structure and a three-span highway bridge for demonstration. The features presented in this paper are the modal flexibility-based deflection and curvature both of which are obtained directly from dynamic properties. In the literature, flexibility associated with mode shapes and mode shapes curvatures have been mostly explored. In this study, multi-input–multi-output dynamic data are used to obtain modal flexibility, which is a close approximation to the actual flexibility. A main novelty is that the curvature is calculated from the deflected shapes using the modal flexibility as opposed to using modal vectors. In this paper, the theory of the methodology is explained and then experimental studies and results are presented. For the experimental studies, the laboratory specimen and the three-span bridge were gradually damaged. It is shown that both deflection and curvature are conceptual and physically meaningful features for damage detection and localization. The issues and the requirements for these features to perform successfully are also presented.     

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO2 for no reduction by NH3

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO₂ for NO reduction by NH₃ was examined in a fixed-bed flow reactor. The deactivation of the catalyst was strongly dependent on reaction temperature. At high reaction temperatures over 300°C, the catalyst did not lose its initial activity up to 50 h of operation, regardless of SO₂ feed concentration from 500 to 20,000 ppm. However, at low reaction temperatures near 250°C, apparent deactivation did occur. Changes in the physicochemical properties such as surface area and sulfur content of deactivated catalyst well correlated with catalyst activity, depending upon reaction temperatures. The deactivation was due to pore blocking and/or filling by deactivating agents, which plugged and/or filled the pores of catalyst. The deactivating agents deposited on the catalyst surface were presumed to be (NH₄)₂SO₄ and/or (NH₄)HSO₄ from the results of TGA and ion-chromatography measurement.     

Ultrahigh molecular weight polyethylene with improved crosslink density,oxidation stability,and microbial inhibition by chemical crosslinking and tea polyphenols for total joint replacements

Highly crosslinked ultrahigh molecular weight polyethylene (UHMWPE) stabilized by vitamin E (VE) is widely applied in artificial joints as the bearings. Despite the approval, there is a discord that VE lowers the crosslinking efficiency, limiting its use at high concentration. In this work, we aim to obtain highly crosslinked and oxidation resistant UHMWPE through the conjunction of tea polyphenol and chemical crosslinking. We hypothesized that highly incorporated tea polyphenol with multiple reactive sites can ameliorate crosslinking efficiency of chemical crosslinked UHMWPE in comparison to VE. Epigallocatechin gallate (EGCG) as representative tea polyphenol was incorporated into UHMWPE at high concentration (2–8 wt%), followed by chemical crosslinking with 2 wt% organic peroxide. Unlike VE/UHMWPE blends as the control, chemical crosslinking achieved an increasing trend in crosslink density of EGCG/UHMWPE blends with increasing antioxidant concentration. High concentration of EGCG also enhanced the oxidation stability of UHMWPE. Intriguingly, EGCG endowed UHMWPE with an excellent antimicrobial property, which was inefficient in VE/UHMWPE. Cell viability was hardly affected by the high loaded antioxidant and peroxide. The chemically crosslinked UHMWPE blended with EGCG is proved to be a reasonable, cost effective and realistic alternative for use in artificial joints.     

单翼迷宫式滴灌带抗热氧老化性能的影响研究

单翼迷宫式滴灌带产品新国家标准中增加了氧化诱导时间（OIT）,这对产品的抗热氧老化性能提出了要求。本文从滴灌带配方出发,讨论了产品原料与其OIT的料效关系,结果表明,防老化母料的加入比例对滴灌带的OIT影响最大,增加其比例可增大滴灌带的OIT;高密度聚乙烯（PE?HD）的加入比例对滴灌带的OIT影响大于线性低密度聚乙烯（PE?LLD）和低密度聚乙烯（PE?LD）的加入比例,增加PE?HD比例、减小PE?LLD和PE?LD比例可增大滴灌带的OIT;PE?LD的加入比例对滴灌带OIT的影响最小,在配方设计时应综合使用比例合理的PE?HD、PE?LLD、PE?LD以满足滴灌带良好的加工和其他性能要求;防老化母料中稳定剂比例不应随成本而减少,稳定剂比例增大时,滴灌带的OIT增大;通过对滴灌带的熔体质量流动速率（MFR）、炭黑含量及OIT指标测试,得出滴灌带MFR和炭黑含量与其OIT无明显的相互变化关系。     

Trimetallic PtCoFe Alloy Monolayer Superlattices as Bifunctional Oxygen‐Reduction and Ethanol‐Oxidation Electrocatalysts

A synthesis strategy for the preparation of trimetallic PtCoFe alloy nanoparticle superlattices is reported. Trimetallic PtCoFe alloy monolayer array of nanoparticle superlattices with a large density of high index facets and platinum‐rich surface are successfully prepared by coreduction of metal precursors in formamide solvent. The concentration of cetyl trimethyl ammonium bromide plays a vital role for the formation of a monolayer array of nanoparticle superlattices, while the size of nanoparticles is determined by NaI. The prepared monolayer array of nanoparticle superlattices is the superior catalyst for oxygen reduction reaction as well as for ethanol oxidation owing to their specific structural and compositional characteristics.     

Three-dimensional macroscale assembly of Pd nanoclusters

Construction of macro-materials with highly oriented microstructures and well-connected interfaces between building blocks is significant for a variety of applications. However, it is still challenging to confine the desired structures. Thus, well-defined building blocks would be crucial to address this issue. Herein, we present a facile process based on 1.8 nm Pd nanoclusters (NCs) to achieve centimeter-size assemblages with aligned honeycomb structures, where the diameter of a single tubular moiety is ～4 μm. Layered and disordered porous assemblages were also obtained by modulating the temperature in this system. The reconciled interactions between the NCs were crucial to the assemblages. As a comparison, 14 nm Pd nanoparticles formed only aggregates. This work highlights the approach of confining the size of the building blocks in order to better control the assembly process and improve the stability of the structures.

Open image in new window

     

Energy-saving manufacturing technology for high-strength metal products

The use of heat-strengthened blanks to manufacture cold-deformed rebar and high-performance bolts permits the elimination of some operations in the production process, with corresponding energy savings. The complete research cycle includes the development of the technology, formulation of the documentation, and industrial trials.