Scalability and performance of an agent‐based network management middleware

Rapid growth of computer network sizes and uses necessitate analysis of network application middleware in terms of its scalability as well as performance. In this paper we analyze a distributed network management middleware based on agents that can be dispatched to locations where they can execute close to the managed nodes. The described middleware operates between the network protocol layer and the application layer and uses standard TCP protocol and SNMP probes to interface the network. By aggregating requests from many users into a single agent, our system allows multiple managers to probe problem areas with minimal management traffic overhead. We discuss and quantify the benefits of the described middleware by implementing real‐time network managers using our system. The main result of this paper is a comparison of scalability and efficiency of our agent‐based management middleware and traditional SNMP‐based data collection. To this end, we measured traffic in both real and simulated networks. In the latter case, we designed, used and described here a method of separating simulated application flow into separate subflows to simplify design of simulations. Copyright © 2004 John Wiley & Sons, Ltd.     

On the computation of conjugacy classes of Chevalley groups

In this paper an algorithm is presented to determine the number of semisimple conjugacy classes for a given centralizertype for the Chevalley groupsSL _n(q) andSU _n(q). Moreover we give the exact number of regular semisimple classes of this groups and a summary of results on the generic classnumber of exceptional Chevalley groups of adjoint type.The first author acknowledges financial support by a grant of the Deutsche Forschungsgemeinschaft     

Hilfsmittel zum Auffinden einer ersten Gestalt beim methodischen Konstruieren: Gestaltbeeinflussung durch die Verwendung physikalischer Effekte

Zusammenfassung Ziel des Teilvorhabens, über das hier berichtet wird, was es, für eine Auswahl von physikalischen Effekten eine Zuordnung von gestaltbeeinflussenden Merkmalen auf sehr abstrakter Ebene zu erreichen und damit eine n?here Charakterisierung der Wirkfl?chen und Wirkr?ume zu erreichen die zur Umsetzung eines physikalischen Effektes notwendig sind. Die hieraus resultierenden Ergebnisse sind dem Abschlu?bericht zu entnehmen [1]. Weiterführende Themen, die basierend auf den vorliegenden Erkenntnissen bearbeitet werden, haben zum Ziel, die wesentlichen und entscheidenden Parameter einer Konstruktionsaufgabe zu erkennen und zukünftig zielgerichtet L?sungsvarianten zu erstellen, um somit für eine Neukonstruktion sinnvolle L?sungsfelder sehr frühzeitig abzugrenzen.     

Minimum spanning trees made easier via multi-objective optimization

Many real-world problems are multi-objective optimization problems and evolutionary algorithms are quite successful on such problems. Since the task is to compute or approximate the Pareto front, multi-objective optimization problems are considered as more difficult than single-objective problems. One should not forget that the fitness vector with respect to more than one objective contains more information that in principle can direct the search of evolutionary algorithms. Therefore, it is possible that a single-objective problem can be solved more efficiently via a generalized multi-objective model of the problem. That this is indeed the case is proved by investigating the computation of minimum spanning trees.This work was supported by the Deutsche Forschungsgemeinschaft (DFG) as part of the Collaborative Research Center Computational Intelligence (SFB 531) and by the German-Israeli Foundation (GIF) in the project Robustness Aspects of Algorithms.     

Microcalorimetry for characterization of film formation and cure of coatings and adhesives

A new microcalorimeter with eight parallel channels using robust, low cost sensors for characterization of coatings and adhesives is described and first experiments on coatings and adhesives are presented. The calorimetric sensors are based on thin glass plates (20 mm × 20 mm, thickness 150 μm) with heater and thermocouple sputtered on the surfaces (calorimetric active area of about 9 mm²). The setup allows heating and cooling experiments as well as isothermal measurements in the temperature-modulated mode with up to eight sensors in parallel. The measured quantities are the real (C^′_p) and imaginary part (C^″_p) of the complex heat capacity (), the related absolute value of the heat capacity () and the heat flow . An industrial computer (NI PXI system) with specific software for calibration and data recording controls the electronic components. Sensors can be embedded in a temperature controlled oven (heating and cooling by Peltier elements) or alternatively in a climatic cabinet with controlled temperature and humidity.

The method has been applied successfully to monitoring of film formation of aqueous polymer dispersions (styrene-acrylate copolymer) and curing of coatings.     

XPS investigation on AISI 420 stainless steel corrosion in oil and gas well environments

The corrosion behaviour of 13Cr-martensitic stainless steel (AISI 420) was investigated in CO₂-H₂S-Cl^– environments typical of oil and gas wells under different CO₂ and H₂S partial pressures. The corrosion tests indicated that the AISI 420 steel was highly corrosion resistant to CO₂-induced phenomena (general corrosion and carbonate S.C.C.), while in the H₂S environment a high S.S.C.C. (Sulphide Stress Corrosion Cracking) susceptibility and high corrosion rates were found. Moreover, CO₂ in CO₂-H₂S-Cl^– systems inhibited general corrosion and S.S.C.C. phenomena by favouring the formation of a protective film. By means of X-ray photoelectron spectroscopy (XPS) the chemical nature of the films grown on AISI 420 in different environmental conditions was investigated and the following statements were drawn out:

Dynamic light scattering and ultrasonic investigations during the cure reaction of an epoxy resin

Brillouin scattering (BS), photon correlation spectroscopy (PCS), and ultrasonic (US) measurements were conducted to study the curing process of diglycidyl ether of bisphenol A with butane-1,4-diol at a curing temperature of 100°C. The experimental techniques probe the primary glass-rubber transition during the curing reaction. The primary relaxation time τ obtained from the BS and US velocity and absorption increases with curing time and hence the BS experiment measures τ at earlier stages of cure than the US experiment. The relaxation times at a different extent of reaction and for different measuring temperatures are consistent with BS, US, PCS, and DSC measurements and conform to a single reduced Vogel–Fulcher–Hesse–Tamann equation. Furthermore, the US experiments show evidence of secondary relaxations in the epoxy system.     

Rheological and dielectrical characterization of melt mixed polycarbonate-multiwalled carbon nanotube composites

A series of composites of polycarbonate (PC) with 23 different contents of multiwalled carbon nanotubes (MWNT) was produced by melt mixing using the masterbatch dilution method. In dielectric measurements, AC conductivity and complex permittivity data obtained in the frequency range between 10⁻³ and 10⁷ Hz at room temperature indicated the electrical percolation threshold at about 1.0 wt%.

The dynamic mode melt rheological measurements for the same samples at eight temperatures between 170 and 280 °C showed a visible change in the frequency dependence of dynamic moduli and the absolute value of the complex viscosity |η*| particularly at low frequencies. In literature these changes are sometimes related to so called ‘percolation threshold concentration’. Applying this picture to our experimental data we have to assume that the percolation threshold is strongly dependent on the measurement temperature. It changes from about 5 to 0.5 wt% MWNT by increasing the measurement temperature from 170 to 280 °C, respectively. This temperature dependence cannot be explained by a classical liquid-solid transition but may be related to the existence of a combined nanotube-polymer network.     

The Integration of Vacuum Brazing into Heat Treatment - A Progressive Combined Process

The continuous constructive challenge to improve the functionality and efficiency of components always results in higher demands on production engineering, against the background of the generally increasing cost pressure. In many cases, you will just succeed in producing competitive and innovative products by combining and coupling of different procedures to an independent (hybrid) technology. The use of hybrid procedures for metal joining and heat treatment of metallic materials finds more and more industrial fields of application. Modern vacuum lines with integrated pressurized gas quenching are considered high-performance and flexible means of production for brazing and heat treatment tasks as well in the turbine industry as in the mould making and tool manufacturing industry. In doing so, the heat treatment is coupled with the brazing cycle in a combined process so that the brazing temperatures and soak times are adapted to the necessary temperatures and times for solution heat treatment and austeniting. This user-oriented article describes on the one hand examples of brazing of turbine components, but above all the practical experience from the plastics processing industry, where the requirement for a high-efficient cooling of injection moulding dies gains more and more importance.The combined procedure “Vacuum Brazing and Hardening” offers plenty of possibilities to produce mould inserts with an efficient tempering system in an economic way.