Al-Ga-Mn-Ca-Cu合金电极碱性体系电化学性能

通过熔铸、压延、退火等一系列工艺制作了新型Al-0.017Ga-0.885Mn-0.038Ca-0.048Cu (wt.%)阳极合金，并通过了EIS、极化曲线分析研究了其在不同浓度NaOH溶液中的腐蚀行为和电化学性能。结果表明，随着NaOH浓度的增加，合金阳极的自腐蚀速率在逐渐增加，Al-0.017Ga-0.885Mn-0.038Ca-0.048Cu合金在4mol/LNaOH溶液中的腐蚀速率增长速度明显降低，放电电压在电流密度为120mA/cm2下仍能维持在1 V左右，阳极能量密度也最高，达6.056kW?h/kg，更适合不同电流密度下的连续恒流放电。且合金的恒流放电和EIS结果与腐蚀特性吻合较好。     

Study on effect of diverse air inlet arrangement on thermal management of cylindrical lithium-ion cells

Lithium-ion cells are preferred in the electrical powertrain due to high-power density, compactness, and modularity. In real driving conditions, the cells undergo discharge rates as high as 4 C resulting in high heat generation affecting the performance. To obtain the maximum performance the pack construction and thermal management of cells are crucial parameters. In our work, air-cooled technique with diverse air inlet and staggered scheme with a two-channel partition approach for thermal management of the cylindrical lithium-ion cells are studied in computational fluid dynamics. The simulation model is validated with experimental results. The obtained results demonstrate that the cells in the dual-directional air inlet arrangement had low maximum temperature difference among and within the cells and required least fan work. This arrangement required least fan work to generate optimal air inlet velocity of 2 m/s for 1, 2, and 3 C and 4 m/s for 4 C discharge rates. There is a reduction of 50% and 33% fan work for 3 and 4 C discharge rates, which are the majority operating points. Also, it shows that the temperature uniformity within the cells has improved. The results of this study can used to optimize parameters for designing an enhanced thermal management system.     

Effect of CoFe2O4 mole percentage on multiferroic and magnetoelectric properties of Na0.5Bi0.5TiO3/CoFe2O4 particulate composites

Na_0.5Bi_0.5TiO₃ (NBT), CoFe₂O₄ (CFO) as well as particulate composites containing different mole percentages of NBT and CFO were synthesized by the solid-state sintering route and characterized for their ferroelectric and ferrimagnetic hysteresis loops, magnetostriction and magnetoelectric (ME) output. The mole% of CFO was found to influence the ferroelectric and ferrimagnetic hysteresis loops as well as magnetostriction and piezomagnetic coefficients which in turn had a significant effect on the magnetoelectric voltage coefficient. The highest magnetoelectric voltage coefficient (α) of 0.5 mV/cm/Oe was recorded in (65) NBT–(35) CFO composite.     

A Note on Moments of Gamma Order Statistics

Previously quadrature approximations were developed to determine the moments of a distribution of the response of a multivariable function when each of the variables is a random variable from a normal distribution. The error was shown to be of the order of the sixth power of the standard deviations of the random variables, but a more useful bound is desired in applied work. Only limited success has been achieved in this direction. It is shown that the best approximating distribution is a Beta distribution of the first kind with β₂ equal to 3 and mean, variance, and β₁ obtained by quadrature, where β₁ and β₂ are standard measures of skewness and kurtosis, respectively. A parametric study of the function X = C_o (a _o, ± y ₁ ± y ₂ ± … ±y_n ) ^m + b _o where the y_i all have the same standard deviation, σ, is conducted both analytically and by quadrature. The mean and variance obtained by quadrature are essentially exact in the range of interest. It is shown that for a large range of σ the above distribution is both a good approximation and a much better approximation than either a normal approximation with the same mean and variance or a linear approximation. The example also shows that the β₂ obtained by quadrature is a poor indicator of the precision of the quadrature approximation.     

A review of the antioxidant potential of medicinal plant species

Some researchers suggest that two-thirds of the world's plant species have medicinal value; in particular, many medicinal plants have great antioxidant potential. Antioxidants reduce the oxidative stress in cells and are therefore useful in the treatment of many human diseases, including cancer, cardiovascular diseases and inflammatory diseases. This paper reviews the antioxidant potential of extracts from the stems, roots, bark, leaves, fruits and seeds of several important medicinal species. Synthetic antioxidants such as butylated hydroxytoluene (BHT) and butylated hydroxylanisole (BHA) are currently used as food additives, and many plant species have similar antioxidant potentials as these synthetics. These species include Diospyros abyssinica, Pistacia lentiscus, Geranium sanguineum L., Sargentodoxa cuneata Rehd. Et Wils, Polyalthia cerasoides (Roxb.) Bedd, Crataeva nurvala Buch-Ham., Acacia auriculiformis A. Cunn, Teucrium polium L., Dracocephalum moldavica L., Urtica dioica L., Ficus microcarpa L. fil., Bidens pilosa Linn. Radiata, Leea indica, the Lamiaceae species, Uncaria tomentosa (Willd.) DC, Salvia officinalis L., Momordica Charantia L., Rheum ribes L., and Pelargonium endlicherianum. The literature reveals that these natural antioxidants represent a potentially side effect-free alternative to synthetic antioxidants in the food processing industry and for use in preventive medicine.     

Macroscopic properties of liquid-solid circulating fluidized bed with viscous liquid medium

Experiments were conducted in a liquid-solid circulating fluidized bed to study the effect of liquid viscosity and solids inventory on pressure gradient, critical transitional liquid velocity, onset average solids holdup, axial solids holdup distribution, average solids holdup and solids circulation rate in circulating fluidization regime with riser operated in fixed inventory mode. The results indicate that critical transitional liquid velocity decreases with increase in liquid viscosity. The onset average solids holdup, on the other hand, increases with increase in either auxiliary liquid velocity or solids inventory. The variation of axial solids holdup distribution, average solids holdup and solids circulation rate with liquid viscosity when solid inventory was 0.15 m was dissimilar with either 0.25 m or 0.35 m solid inventory. Correlations were proposed for estimating the average solids holdup and are satisfactorily compared with experimental values.     

A stable subgridding algorithm and its application to eigenvalueproblems

In this paper, a new and stable subgridding algorithm is proposed for three-dimensional problems which provides subgridding in both space and time. The concept of an equivalent-circuit representation and a novel leapfrog time integration scheme is used to ensure that the algorithm is stable and efficient. Practical applications of this algorithm in the characterization of arbitrarily filled dielectric resonators are reported     

Identification of 130 kDa cell surface LDL-binding protein from smooth muscle cells as a partially processed T-cadherin precursor

Atypical cell surface lipoprotein-binding proteins of 105 kDa and 130 kDa are present in membranes of vascular smooth muscle cells. We recently identified the 105 kDa protein from human aortic media as T-cadherin, an unusual glycosylphosphatidylinositol (GPI)-anchored member of the cadherin family of cell adhesion proteins. The goal of the present study was to determine the identity of 130 kDa lipoprotein-binding protein of smooth muscle cells. We applied different approaches that included protein sequencing of purified protein from human aortic media, the use of human T-cadherin peptide-specific antisera, and enzymatic treatment of cultured cells with trypsin and GPI-specific phospholipase C. Our results indicate that the 130 kDa protein is a partially processed form of T-cadherin which is attached to the membrane surface of smooth muscle cells via a GPI anchor and contains uncleaved N-terminal propeptide sequence. Our data disclose that, in contrast to classical cadherins, T-cadherin is expressed on the cell surface in both its precursor (130 kDa) and mature (105 kDa) forms.     

A new correction procedure for calibrating dental caries frequency

The incisors and canines and the premolars and molars show differential resistance to cariogenic factors. The anterior teeth have a lower caries frequency than the posterior teeth. However, these tooth classes are lost differentially in postmortem stages due to their anatomical structures. This differential postmortem tooth loss distorts proportions between the anterior and posterior tooth classes. The disproportionality can affect the calculation of total caries prevalence. In this paper, we propose a new calibration procedure which removes this disproportionality and call it the proportional correction factor. For this procedure, the caries rates of anterior and posterior teeth are corrected by multiplying the anterior teeth by three-eighths and the posterior teeth by five-eighths. These fractions are derived from the human dental formula which contains three anterior and five posterior teeth by side. The correction factor is more effective if the proportion of anterior to the posterior teeth is extremely distorted. When this procedure is used with the caries correction factor, it provides a useful way to approach to an almost true caries prevalence.     

Design of an Ideal Grain-Refiner Alloy for Al-7Si Alloy Using Artificial Neural Networks

An ideal grain refiner has been designed for Al-7Si alloy by performing sensitivity analysis of trained artificial neural network (ANN) model. An ANNs model has been developed for solving these complex grain refinement phenomena in Al-7Si alloy. The model predictions and the analysis are well in agreement with the experimental results and existing metallurgical facts. Uncertainty in predictions helped in finding a new phenomenon at lower addition levels of grain refiner.