Molecular Dynamics Study of Radial Corrugation in Carbon Nanotubes

Molecular dynamics simulations of multiwalled carbon nanotubes under hydrostatic pressure are performed to elucidate the novel class of radial buckling in the systems. It is revealed by all-atom simulations that the initial circular cross section transforms into a flower-like wavy configuration at critical pressure on the order of hundreds mega pascals or less. This kind of radial buckling, called radial corrugation, originates from the competition of the three relevant energies in the system: in-plane strain energy, van der Waals interaction energy between adjacent tubes, and out-of-plane bending energy. Their possible consequences for physical properties of carbon nanotubes are also discussed.     

Advanced synthesis for monodisperse polymer nanoparticles in aqueous media with sub-millimolar surfactants

Highly monodisperse polystyrene nanoparticles with mean diameters of less than 100 nm are synthesized via aqueous emulsion polymerization using an amphoteric initiator (VA-057) in the presence of sub-millimolar concentrations of anionic surfactant. Since the net charge on the initiator is almost zero at neutral pH, the resultant latex particle size is mainly determined by surfactant adsorption. Polymerizations were performed in the presence of a range of anionic surfactants with differing critical micelle concentrations (CMC) by varying the concentrations of surfactant, initiator and monomer, and also the ionic strength. Sodium dodecyl benzene sulfonate (SDBS), sodium hexadecyl sulfate (SHS), and sodium octadecyl sulfate (SOS) have relatively low CMCs and so enable formation of highly monodisperse nanoparticles at relatively low (sub-millimolar) surfactant concentrations, C_S (i.e. below the CMC in each case). Empirically, it was found that the particle number, N_p, and coefficient of variation of the particle size, C_V, were strongly dependent on the C_S/CMC ratio: N_p increased almost in proportion with the square of this ratio, while the C_V exhibited a minimum at approximately C_S/CMC = 0.20. Higher ionic strength reduced the particle size, which is consistent with the above relationship because the addition of salt lowers the CMCs of ionic surfactants. Polymer latex particles produced using such formulations form highly regular, close-packed colloidal arrays.     

好氧/厌氧污泥对17β-雌二醇的降解特性

采用好氧、厌氧交替运行的污水处理厂的活性污泥处理内分泌干扰物17β-雌二醇（E2）,分别考察了好氧和厌氧条件下,污泥对E2及其降解中间产物——雌酮（E1）的去除效果,同时考察了污泥混合液中碳源和氮源对E2降解的影响。结果表明,在好氧条件下,活性污泥对E2、E1均有很好的降解效果,E2的未检出时间均在70 min左右,E1的未检出时间均在110 min左右,添加碳源和氮源对E2的降解速率无显著影响。厌氧污泥对E2和E1的降解速率远小于好氧活性污泥的,添加碳源对E2、E1的降解有一定的抑制作用,而添加氮源可以促进对E1的降解,但对E2降解的影响较小。好氧条件下活性污泥对E2的降解符合一级反应动力学方程;厌氧条件下,特别是有NO3^--N存在的条件下,污泥对E2的降解不符合一级反应动力学。     

Pore distribution effect of activated carbon in adsorbing organic micropollutants from natural water

Adsorption isotherms of organic micropollutants in coexistence with natural organic matter (NOM) were analyzed to evaluate the impacts of pore size distribution of activated carbon (AC) on the competition effects of the NOM. Single solute adsorption experiments and simultaneous adsorption experiments with NOM contained in a coagulation-pretreated surface water were performed for four agricultural chemicals and three coal-based activated carbons (ACs) having different pore distributions. The results showed that, for all the carbons used, the adsorption capacity of the chemicals was reduced distinctly in the presence of NOM. Such a reduction was more apparent for AC with a larger portion of small pores suitable for the adsorption of small organic molecules and for the agricultural chemicals with a more hydrophilic nature. Ideal adsorbed solution theory (IAST) incorporated with the Freundlich isotherm expression (IAST-Freundlich model) could not interpret the impact of NOM on the adsorption capacity of the chemicals unless a pore blockage effect caused by the adsorption of NOM was also considered. By taking into account this effect, the adsorption isotherm of the chemicals in the presence of NOM was well described, and the capacity reduction caused by the NOM was quantitatively assessed from the viewpoints of the site competition and the pore blockage. Analytical results clearly indicated that pore blockage was an important competition mechanism that contributed to 10-99% of the total capacity reductions of the chemicals, the level depended greatly on the ACs, the chemicals and the equilibrium concentrations, and could possibly be alleviated by broadening the pore size distributions of the ACs to provide a large volume percentage for pores with sizes above 30 A.     

Microfluidic Spinning of Cell‐Responsive Grooved Microfibers

Engineering living tissues that simulate their natural counterparts is a dynamic area of research. Among the various models of biological tissues being developed, fiber‐shaped cellular architectures, which can be used as artificial blood vessels or muscle fibers, have drawn particular attention. However, the fabrication of continuous microfiber substrates for culturing cells is still limited to a restricted number of polymers (e.g., alginate) having easy processability but poor cell–material interaction properties. Moreover, the typical smooth surface of a synthetic fiber does not replicate the micro‐ and nanofeatures observed in vivo, which guide and regulate cell behavior. In this study, a method to fabricate photocrosslinkable cell‐responsive methacrylamide‐modified gelatin (GelMA) fibers with exquisite microstructured surfaces by using a microfluidic device is developed. These hydrogel fibers with microgrooved surfaces efficiently promote cell encapsulation and adhesion. GelMA fibers significantly promote the viability of cells encapsulated in/or grown on the fibers compared with similar grooved alginate fibers used as controls. Importantly, the grooves engraved on the GelMA fibers induce cell alignment. Furthermore, the GelMA fibers exhibit excellent processability and could be wound into various shapes. These microstructured GelMA fibers have great potential as templates for the creation of fiber‐shaped tissues or tissue microstructures.     

Numerical computation of two-loop box diagrams with masses

A new approach is presented to evaluate multi-loop integrals, which appear in the calculation of cross-sections in high-energy physics. It relies on a fully numerical method and is applicable to a wide class of integrals with various mass configurations. As an example, the computation of two-loop planar and non-planar box diagrams is shown. The results are confirmed by comparisons with other techniques, including the reduction method, and by a consistency check using the dispersion relation.     

Effects of water chemistry and potential distribution on electrochemical corrosion potential measurements in 553 K pure water

The effects of water chemistry distribution on the potential of a reference electrode and of the potential distribution on the measured potential should be known qualitatively to obtain accurate electrochemical corrosion potential (ECP) data in BWRs. First, the effects of oxygen on a platinum reference electrode were studied in 553 K pure water containing dissolved hydrogen (DH) concentration of 26–105 μg kg^?1 (ppb). The platinum electrode worked in the same way as the theoretical hydrogen electrode under the condition that the molar ratio of DH to dissolved oxygen (DO) was more than 10 and that DO was less than 100 ppb. Second, the effects of potential distribution on the measured potential were studied by using the ECP measurement part without platinum deposition on the surfaces connected to another ECP measurement part with platinum deposition on the surfaces in 553 K pure water containing 100–130 ppb of DH or 100–130 ppb of DH plus 400 ppb of hydrogen peroxide. Measured potentials for each ECP measurement part were in good agreement with literature data for each surface condition. The lead wire connecting point did not affect the measured potential. Potential should be measured at the nearest point from the reference electrode in which case it will be not affected by either the potential distribution or the connection point of the lead wire in pure water.     

Microstructure of Interfacial Region Between Cold-Sprayed Copper Coating and AlN Substrate Coated with Sputtered Titanium and Copper

Cold spraying has been developed as a high-quality coating technique. In this article, copper is deposited on an AlN substrate coated by the sputtering of titanium and copper at a low pressure of less than 1.0 MPa, making this approach suitable for a wide range of engineering applications. In order to understand the adhesion mechanism at the atomic scale, the interfacial regions are carefully observed in thin foil samples from the cross sections of the specimens with a HREM. We find a unique wavy boundary between the sputtered titanium and the sputtered copper. It is assumed that the shear-instability phenomenon occurs due to the cold-spraying process and influences the adhesive strength. Furthermore, the cold-sprayed copper particles are connected directly without any oxidation layer due to the appearance of new metallic surfaces during the impact process. The TEM data clearly reveal the phenomena and mechanisms related to the impact of powder sprayed on the substrate.     

Structure and properties of poly(vinyl alcohol)/κ‐carrageenan blends

Blends of a commercial atactic poly(vinyl alcohol) (a‐PVA) derived from vinyl acetate and κ‐carrageenan were prepared by mixing the aqueous solutions of both samples. Blend films prepared by casting were transparent. In the DSC curves of the blend films, the endothermic peaks shifted to lower temperature with an increase of the content of κ‐carrageenan. The Young's modulus and the strength at break increased with an increase of the content of a‐PVA. As the standing temperature of the blend solutions decreased, the gelation region increased also at high content of carrageenan. In the amorphous regions of blend films, a‐PVA and κ‐carrageenan were miscible. © 2001 Society of Chemical Industry