Feasibility of high performance in p-type Ge1−xBixTe materials for thermoelectric modules

GeTe is a promising candidate for the fabrication of high-temperature segments for p-type thermoelectric (TE) legs. The main restriction for the widespread use of this material in TE devices is high carrier concentration (up to ∼ 10²¹ cm⁻³), which causes the low Seebeck coefficient and high electronic component of thermal conductivity. In this work, the band structure diagram and phase equilibria data have been effectively used to attune the carrier concentration and to obtain the high TE performance. The Ge_1−xBi_xTe (x = 0.04) material prepared by the Spark plasma sintering (SPS) technique demonstrates a high power factor accompanied by moderate thermal conductivity. As a result, a significantly higher dimensionless TE figure of merit ZT = 2.0 has been obtained at ∼ 800 K. Moreover, we are the first to propose that application of the developed Ge_1−xBi_xTe (x = 0.04) material in the TE unicouple should be accompanied by SnTe and CoGe₂ transition layers. Only such a unique solution for the TE unicouple makes it possible to prevent the negative effects of high contact resistance and chemical diffusion between the segments at high temperatures.     

Compositional Dependence of Normal Spectral Emissivity of Molten Cu-Fe Alloy

Metallurgical and Materials Transactions B - Normal spectral emissivity of molten Cu-Fe alloy with different compositions was measured at the wavelength of 807 nm using an electromagnetic...     

A generation method of artificial fluctuation data of wind power output considering smoothing effect

To use realistic wind power fluctuation data is important in simulating frequency change of power systems. It is well known that the smoothing effect must be taken into account when generating the artificial wind power output. Therefore, this paper proposed a new method to generate fluctuation waveform considering smoothing effect based on random number to fulfill the correlation among multiple sites and autoregression model. The effectiveness of the proposed method was tested by using practical wind speed data measured in Tohoku district.     

High permittivity BaTiO3 and BaTiO3-polymer nanocomposites enabled by cold sintering with a new transient chemistry: Ba(OH)2∙8H2O

Cold sintering process (CSP) offers a promising strategy for the fabrication of innovative and advanced high permittivity dielectric nanocomposite materials. Here, we introduce Ba(OH)₂?8H₂O hydrated flux as a new transient chemistry that enables the densification of BaTiO₃ in a single step at a temperature as low as 150 °C. This remarkably low temperature is near its Curie transition of 125 °C, associated with a displacive phase transition. The cold sintered BaTiO₃ shows a relative density of 95 % and a room temperature relative permittivity over 1000. This new hydrated flux permits the fabrication of a unique dense BaTiO₃-polymer nanocomposite with a high volume fraction of ceramics ((1-x) BaTiO₃ – x PTFE, with x = 0.05). The composite exhibits a relative permittivity of approximately 800, at least an order of magnitude higher than previous reports on polymer composites with BaTiO₃ nanoparticle fillers that are typically well below 100. Unique high permittivity dielectric nanocomposites with enhanced resistivities can now be designed using polymers to engineer grain boundaries and CSP as a processing method opening up new possibilities in dielectric materials design.     

A design and simulation tool for ground source heat pump system using energy piles with large diameter

Calculation of the underground temperature resulting from heat injection/extraction into/from ground heat exchangers (GHEXs) with hourly variation is one of the most noteworthy challenges to address when simulating and designing a ground source heat pump (GSHP). In order to overcome this challenge, the authors introduce a method to calculate the underground temperature, by considering heat injection/extraction into/from GHEXs with hourly variation. The method applies the superposition of the infinite cylindrical source (ICS) solution and the infinite line source (ILS) solution to calculate the temperature change due to heat injection/extraction into/from the considered GHEX and other neighboring GHEXs, respectively. The calculation method also considers heat injection/extraction from GHEXs with different heat injection/extraction rates and is able to accommodate GHEXs with large diameters such as energy piles. The calculation method was evaluated by applying it to calculate the temperature variation of the heat carrier fluid in a GSHP system with energy piles.