Effect of sand and clay fouling on the shear strength of railway ballast for different ballast gradations

Ballast contamination by fine materials such as sand and clay in railway track at arid regions is an important issue that causes track instability problems and settlement due to reduction of shear strength of ballast. In this paper, the results of direct shear box test conducted on clean ballast, sand-fouled ballast and clay-fouled ballast for different ballast gradations are reported and discussed. For this purpose, three different fouling amounts according to fouling index are added to clean ballast. Test results show that by increasing the fouling percentage, the ballast shear strength always decreases both for sand and clay fouled ballast. However, the amount of shear strength reduction is low at high normal stresses. Clay contamination has more adverse effect on the shear strength of ballast compared with sand contamination. Also, the results of tests for evaluation of gradation effect on shear strength of fouled ballast which are conducted on various gradations according to American Railway Engineering and Maintenance-of-Way Association, show that the maximum particle size as well as uniformity coefficient affect the shear strength of ballast. Also, an empirical equation is presented to observe the effect of ballast gradation on reduction of shear strength with regard to amount of fouling material and normal stress.     

Effect of processing method on vitamin profile,antioxidant properties and total phenolic content of coconut (Cocos nucifera L.) sugar syrup

Coconut (Cocos nucifera L.) sugar is a more nutritious alternative sugar source as compared to sugar palm (Borassus flabellifer) and sugarcane (Saccharum officinarum L.). This work was aimed to investigate the browning index (BI), vitamin profile and antioxidant properties of coconut sap sugar syrups, which were produced by different processing methods: rotary evaporation (RE), microwave evaporation (ME) and open-heat evaporation (OHE). The results obtained showed that coconut sugar syrup produced by RE-60 contained high antioxidant activities [DPPH (36.71%) and ABTS (34.84%), TPC (299.87 mg per 100 g sample) and FRAP (3.74 mm )]. These values were slightly lower than those of ME and OHE. Coconut sugar syrup (RE-60) also contained higher amounts of vitamin C (1587.27 mg L⁻¹), vitamin B1 (97.44 mg L⁻¹) and vitamin B3 (19.84 mg L⁻¹) compared with those of ME and OHE coconut sugar syrups. RE-60 was the best method to produce coconut sugar syrup in a shorter time with lower browning index and higher vitamin contents.     

Coherent control of symmetric and asymmetric diffraction grating via relative phase

ABSTRACT

We present a theoretical model to realize the symmetric and asymmetric diffraction grating in a four-level atomic medium. The proposed atomic medium follows a double lambda configuration where four fields interact with it. We get control over symmetric and asymmetric behavior of the diffraction grating by manipulating the relative phase of the fields. Interestingly, the symmetric and asymmetric diffraction grating become prominent when the vortex beam is used instead of the plane wave. Enhanced first, second, and third-order diffraction gratings are achieved via the vortex beam. Further, we find control over asymmetric diffraction gratings by the relative phase of the fields. Coherent control of asymmetric diffraction grating in negative and positive diffracted angles is also achieved via the relative phase.     

Soret and Dufour effects between two rectangular plane walls with heat source/sink

This study addresses the thermo‐diffusion and the diffusion‐thermo phenomena in a semi‐infinite absorbent channel whose walls are contracting/expanding, with heat source/sink effects. The governing partial differential equations with suitable boundary conditions are transformed to a system of dimensionless ordinary differential equations. An analytic solution of the problem has been found using a technique called homotopy analysis method (HAM). HAM gives consistently valid answers to the problem over an extensive variety of parameters and also provides better accuracy. To validate the analytical results, a comparison has been presented with a numerical solution calculated by using the parallel shooting method. The effects of dimensionless parameters, that is, deformation parameter, Reynolds number, Soret and Dufour numbers, and heat source/sink parameter on the expressions of velocity, temperature, and concentration profiles are analyzed graphically to understand the physics of the deformable channel. It has been noted that the velocity across the channel is higher for the expanding channel, as compared to that for the contracting channel. Also the Soret and Dufour number increases the temperature of the fluid, and decreases the concentration. The temperature profile has an increasing behavior in the case of heat source, and a decreasing behavior in the case of heat sink.     

Investigation of functional core-rim composite part production by inserted powder injection moulding

In this study, the use of Cu and Ni interlayers have been investigated for functional core-rim composite part production with WC-Co 9?wt-% feedstock/steel. For this purpose, different experiments have been performed and joining condition, shear strength and microstructure of the intermediate region have been examined. It has been found that AISI 4340 insert/WC-Co have been joined and 85.8?MPa shear strength achieved, but high speed steel insert has not joined. Moreover, it has been determined that better results are obtained with Ni interlayer. Under the same conditions, when the 40?µm Ni interlayer has been used between AISI 4340 core and WC-Co rim, shear strength has been increased approximately twice and has been 162.7?MPa.     

Mechanochemical sulfidization of a mixed oxide-sulphide copper ore by co-grinding with sulfur and its effect on the flotation efficiency

Mechanochemical sulfidization of a mixed sulfide/oxide copper ore by co-grinding with sulfur and additives including Mg(NO₃)₂ and Fe(NO₃)₃ salts and iron, aluminum and magnesium powders was investigated for the first time. Also, the influence of sulfidization during the wet-milling process was examined on the separation efficiency and recovery of copper in detail. The results demonstrated that co-grinding with sulfur solely had the best flotation performance at the value of 0.5 wt.% and it was attributed to the possible existence of S-O bonding on copper oxides surfaces. In addition, adding magnesium nitrate salt, magnesium powder, iron nitrate salt and aluminum powder as additive associated with 0.5 wt% sulfur into ball milling caused the flotation improvement at the amounts of 0.2 wt%, 0.2 wt%, 0.5 wt% and 0.5 wt%, respectively. Also, the effect of grinding time and sulfidization pH with 0.5 wt% sulfur solely was determined and pHs of 7.5 to 8.5 gave the best results. The highest recovery (75.76%) and separation efficiency (63.44%) were achieved at pH of 7.5 and 8.5, respectively.     

Preparation of hydrophobic flat sheet membranes from PVDF-HFP copolymer for enhancing the oxygen permeance in nitrogen/oxygen gas mixture

In this study, poly(vinilydene fluoride-co-hexafluoropropylene)(PVDF-HFP) was used for preparation of hydrophobic membranes using non-solvent induced phase inversion(NIPS) technique. PVDF-HFP copolymer with concentrations of 10 wt% and 12 wt% was prepared to investigate the effect of polymer concentration on pore structure,morphology, hydrophobicity and performance of prepared membranes. Besides, the use of two coagulation baths with the effects of parameters such as coagulant time, polymer type and concentration, and the amount of nonsolvent were studied. The performance of prepared membranes was evaluated based on the permeability and selectivity of oxygen and nitrogen from a gas mixture of nitrogen/oxygen under operating conditions of feed flow rate(1–5 L·min~(-1)), inlet pressure to membrane module(0.1–0.5 MPa) and temperatures between 25 and 45 °C. The results showed that the use of two coagulation baths with different compositions of distillated water and isopropanol,coagulant time, polymer type and concentration, and the amount of non-solvent additive have the most effect on pore structure, morphology, thickness, roughness and crystallinity of fabricated membranes. Porosity ranges for the three fabricated membranes were determined, where the maximum porosity was 73.889% and the minimum value was 56.837%. Also, the maximum and minimum average thicknesses of membrane were 320.85 μm and115 μm. Besides, the values of 4.7504 × 10~(-7) mol· m~(-2)· s~(-1)· Pa~(-1), 0.525 and 902.126 nm were achieved for maximum oxygen permeance, O_2/N_2 selectivity and roughness, respectively.     

Vibration control of laminated truncated conical shell via magnetostrictive layers

Abstract

In this study feedback control is applied to control the free vibration response of an isotropic truncated conical shell embedded with magnetostrictive layers. Classical shell theory is applied to derive the shell vibration equations. The results are derived based on the Galerkin method and the results are compared with published results and the results of finite element software in order to determine the accuracy of using method. The influence of several parameters such as the thickness of magnetostrictive layers, control gain, length and radius of the large edge of the shell on the vibration suppression of fundamental frequency is determined.